Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Chainsaw cutting crooked Questions

Posts

Chainsaw cutting crooked Questions

#1

Chainsaw cutting crooked Questions

Barry Irby

I have a Stihl chainsaw and one of the chains cuts to one side. Can't MAKE it cut straight down through the log. What's going on? I had the chain sharpened by a local Hardware but it still cuts in a circle. Any suggestions?

Re: Chainsaw cutting crooked Questions

#2

Chuck Jones - West TN

Get a new chain

Chuck Jones - West TN

Probably your shortest path back to happiness is a new $20 chain. Several things can cause this, but I think the most common is uneven cutter wear... wear caused most likely by the store grinding some of the links too much, or at inconsistent angle.

Look closely at the top plates of the cutting links. They should all be pretty much the same length. If they aren't you might try re-filing some of the longer cutters, but most likely it will be pretty hard to make a big difference in it.

If you do see that there is a variation in the cutters, take it back to the store and get them to re-sharpen it.

This is one of the reasons I always file my own chains by hand.

Re: Chainsaw cutting crooked Questions

#3

Re: Chainsaw cutting crooked Questions

Scott Crumpton

If it's only the one chain that has a problem, it's likely that the teeth on one side have been sharpened down a little more than those on the other side or at a slightly different angle. Possibly the depth gauges may have been filed differently. Check the teeth and resharpen as needed to get the same geometry and length on both sides.

If more than one chain has the problem, your bar may need truing. One side of the rail may be worn down more than the other. Try flipping the bar over. You should flip the bar every time you change chains to equalize ware. You can file the bar level with a flat file or a special tool. Also, if a new chain can be wiggled from side to side in the bar groove, you may need to squeeze the groove closed a bit. This does need a special tool. The tools are available form Bailey's for about $25.

Re: Chainsaw cutting crooked Questions

#4

Re: Chainsaw cutting crooked Questions

robo hippy

Most likely a bad sharpening job. I hand file mine as well, and take the same number of strokes per tooth. Not really difficult. Just like sharpening your turning tools, takes a little practice to get the hang of it.

robo hippy

Re: Chainsaw cutting crooked Questions

#5

Re: Chainsaw cutting crooked Questions

Joe Herrmann

I had a similar problem and it turned out to be a problem with the bar.

Re: Chainsaw cutting crooked Questions

#6

Keith Tompkins

Re: Chainsaw cutting crooked Questions

keith tompkins

Hi Barry, If your other chains cut properly, the chain is probably the culprit. Your bar should be flipped over from time to time, and filed flat when ridges form. If the chain is the problem...take it back, but don't let them resharpen. There won't be anything left of it. Make them give you a new one.

Re: Chainsaw cutting crooked Questions

#7

Walt Bennett

But now you don't need a band saw!

Walt Bennett

Re: Chainsaw cutting crooked Questions

#8

Re: Chain

Mark Mandell - Gone Round In Jersey

Barry,

Look carefully at your chain's cutters from the top and from the front.

The cutter must have a sharp "beak" viewed from the top. It must also have a sharp angle where the top and side of the cutter meet.

If, in top view you find that you don't have a sharp point on all of your cutters, the chain needs to be reground.

If, however, you have cutters with the outside corner rounded as in example 2 in the attached pdf, the chain has been ruined, usually by running one side against an embedded rock or anything harder than the chain. In that case, the chain will never cut straight, so just pitch it.

If you've got sharp points on all the cutters, take a mic and carefully measure the length of the cutters on both sides. A chain, to run true, must be balanced, a few long or short cutters on either side will have you cutting curves in no time. Then check your depth gauge bars to make sure they are all even.

I got fed up with mower shops and the like blowing off sharpening chains. I bought a mid-priced chain grinder and do all my own and my friend's chains. I can also vary the grind depending on what kind of wood will be cut. I typically get 15-20 sharpenings on a chain as opposed to 4 or 5 from the shops, and my chains cut smoother and faster.

Lastly, I will dress the bar from time-to-time as mentioned. I don't, however, use a file; instead preferring the grinder. I use my Wolverine plate rest aligned dead center with the spindle, then just kiss one rail until the wear bur is gone, flip the bar end-for-end and do the other rail, then do the same on the other edge of the bar. Doing each rail this way negates any hollow grind from the round grind wheel. You can check your bar for true with a good try-square. Caution: Don't grind too close to your bar's nose and catch one of the sprocket teeth.

Re: Chainsaw cutting crooked Questions

#9

Rob Wallace

Re: Chain

Rob Wallace

Mark:

What brand/model chain saw sharpener did you get? It sounds like you're happy with it...

Rob

Re: Chainsaw cutting crooked Questions

#10

Re: Chain

bill Crommett

Reading this stuff makes me feel that I have been blessed with a reliable Stihl dealer who knows his stuff and doesn't gouge. $3.00 per chain for twenty years, and now only $5.00.

Re: Chainsaw cutting crooked Questions

#11

Re: Chain Grinder *LINK*

Mark Mandell - Gone Round In Jersey

Tecomec FL 136 (Italian)

It's precisely adjustable for both grind angles and the chain stop and clamp are rock solid.

When I bought it from Madsen's it was $230. Been more than 4 years and it has easily paid for itself in sharpening charges and chain wear. You'd have to call them for current pricing. 1-800-822-2808


Madsens

Re: Chainsaw cutting crooked Questions

#12

Re: Chainsaw cutting crooked Questions

Barry Irby

Its an honest to God Stihl chain on a stihl chainsaw. The other chain was cutting as it should until it got dull, so we put this one on the saw, thinking it was good, but it immediately started cutting in a curve. So I took three chains to a local hardware/Stihl dealer and had them sharpened, thinking they would correct anything wrong with the chain. I did not tell them about the problem, thinking it would automatically get corrected. They seemed a little sketchy on the sharpening, but at least hey were not heavy handed. I have had some others grind away about 25% of the teeth for no apparent reason.

I hand filed the chain on the other saw (Husky) after it got dull the next time and that went well.

Re: Chainsaw cutting crooked Questions

#13

Brad Vietje

Re: Chainsaw cutting crooked Questions

Brad Vietje

Barry,

I don't sharpen with the precision that Mark does, but usually when I have a chain that wants to cut curves, it's because one side hit something the other did not, causing one side to be dull while the other side is sharper. This could be from some grit or gravel stuck in the bark, or an embedded nail, bolt, or piece of wire fencing, depending on where the log came from.

The saw will cut a curve toward the dull teeth and away from the sharp ones. You could try hand sharpening just the teeth on the dull side -- usually does the trick for me.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Chainsaw cutting crooked Questions

#14

Re: Chainsaw cutting crooked Questions

Doug Trembath

A belt sander is just the ticket if you need to dress the bar. Keep it perpendicular to the belt surface, and gently guide it along until the guiding surfaces on each side of the slot are clean and smooth. Gently means don't take off too much meat, just finess it until it's smooth again.

Doug Trembath

Re: Chainsaw cutting crooked Questions

#15

Chain Grinder!! *LINK*

Mark Mandell - Gone Round In Jersey

The link is to a chain grinder I just saw on sale at Northern Tools. While I can't be sure from an internet add picture, this "looks" to be the same unit I have. If so, and is merely "private labeled", this is a great deal if you're doing your own chains.


NT Grinder

Re: Chainsaw cutting crooked Questions

#16

PS

Mark Mandell - Gone Round In Jersey

Had one PM that the Northern version was seen uc&p in a showroom, and a lack of rigidity was noted in the model's clamping fixture.

Caveat: The "apple" may have rolled somewhat further from the tree on this one, so guide yourself accordingly.