Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Tool Rack

Posts

Tool Rack

#1

Tool Rack

Kelly in Port Orchard

I have a small shop and want to keep all my turning tools handy and I need plans for a rack. Does anybody have plans on one that will have wheels so I can roll it around. Since I have a fairly small shop, I don't want it to take up too much floor space. If you have plans or pictures of one, please share it. I'm one of those people that can follow plans or duplicate a picture, but have trouble drawing up plans from scratch. I can't even draw a straight line without a ruler. I have seen some that are mounted below the lathe, but I can't do that; so I want one that is a "stand alone" and on wheels. Thanks to all and hope you all have a great 2011.

Re: Tool Rack

#2

Re: Tool Rack

Dick Wilson

Kelly, I had an old Atlas table saw. The only good parts were the table top and the stand. Top is now a router table and the stand is now my movable tool standw/wheels. I attached boards around sides with holes for the tools. Handy work surface for tools in use, etc. I put a piece of plywood inside and use for storage of extra tools. Hope this helps.

Re: Tool Rack

#3

Re: Tool Rack

Ralph Lindberg

Kelly, I don't have photo's but if my description doesn't make sense get a hold of me and you can come over and look.

I have a single height rolling tool chest, entirely drawers. In these drawers are the piece parts, drive centers, live centers, different chuck jaws, all the extras I need near the lathe. I picked it up on close-out at Lowes

On top is a piece of 1inch MDF (Kingston Lumber). Setting on that are several clusters of 7 pieces of ABS Pipe. Some are 1-1/2 inch pipe, one is a set of 2 inch. These are to hold the chisels, point up. To keep the clusters in place, there is a small round plug of wood, glued to the MDF. The center of each cluster fits down over the plug (they are glued to the plug also). This keeps the chisel clusters from falling off when I move the chest.

I also have some open room on the top.

PS, If you are member of OPCAAW, I'm the guy that Larry sent the note out for the retirement party on Monday

Re: Tool Rack

#4

Re: Tool Rack

Galen Vetterick

Check your email.

I ask the same question before and I saved the photos of the lathe tool stands posted for me.

Some really good ideas.

I think someone later said they used the wheeled stand from an old gas grill.

Sorry I did not save them under the persons name to give them credit.

Re: Tool Rack

#5

George Taylor

Tool carousel on rolling tool chest

George Taylor

A couple months ago I built this to go on top of the tool chest I go from one of the big box stores.


George

Re: Tool Rack

#6

Re: Tool Rack

Todd Nebel

Hi Kelly, I recently built this stand/tool holder for my lathe and chisels. I ended up using the table next to me more than the holder for the chisels. What I found was when I'm turning I want to quickly grab and put down my tools, even taking the time to carefully place them on the rack or in a tube just wasn't working for me. My suggestion would be to have a multi-purpose table (maybe on wheels) that you can have close by during turning and then a safe place to store your tools when not in use. I carefully lay my chisels in the top drawer when not using the lathe.

Todd


img

Re: Tool Rack

#7

here's what I use- A craftsman tool cabinet

john lucas

I rigged up a way to put the tools on a rack on the outside of it. All of my faceplates, chucks, etc are inside.


Re: Tool Rack

#8

Re: here's what I use- A craftsman tool cabinet

Peter Lamb

John, you clearly don't have enough tools!

Nice storage system,

Re: Tool Rack

#9

Re: here's what I use- A craftsman tool cabinet

john lucas

You never have enough tools. There's more on the wall behind this unit and the second drawer has all of my hollowing tools.

Re: Tool Rack

#10

Re: here's what I use- A craftsman tool cabinet

Kelly in Port Orchard

Thanks to everyone with their suggestions and pictures. I got a lot of good ideas. Like John said; we never have enough tools or clamps. For Christmas this year, I just told everyone to either give me a "gift card" for the local wood store and buy me some clamps. Thanks again.

Re: Tool Rack

#11

Alan Zenreich

Re: Tool Rack

Alan Zenreich

I purchased a Harbor Freight stool and decided that I really didn't like the cushion. So I repurposed the frame and turntable mechanism into a lathe tool holder.

I added a plywood top, shelf and some casters. Then I affixed various diameters of PVC pipe to the top. So far the turntable has been working out very well for me.

I don't have any problem with the sharp bits of the tools pointing up. I approach the tools carefully, with the respect they deserve.

There's still room to add some more tubes, and I'll likely drill some holes on the bottom shelf wings for more toys, errr, tools.

I hope you find this useful.



Re: Tool Rack

#12

Re: Tool Rack

Todd Nebel

I recently added to my organization with a wall mounted tool holder for the small pieces that get lost under shavings on the table.


img

Re: Tool Rack

#13

Roger in MO

Re: Tool Rack

Roger in MO

I keep my tools on a sheet of plywood hinged to the front leg of my lathe. When not in use, it swings in front of the lathe. Not pretty but it works for me.

Roger in MO.

Re: Tool Rack

#14

Re: Tool Rack *LINK*

Mike Brazeau

I made this combination of stand and carousel about 8 years ago and am still very happy with it. See details at link in Tools & Jigs album. Simple box construction with some good drawer slides.

Image Hosting by PictureTrail.com

Also have a project oriented stand there.


The Joy of Wood

Re: Tool Rack

#16

Re: Tool Rack - tools

bernie feinerman

Alan - I noticed in your tool rack a few tools similar to the Warren "Nano" hollowing tools.

How do you like them? Do you feel they are worth the $$$?

Re: Tool Rack

#17

Re: Tool Rack

Carole Valentine

I adapted this $40 microwave cart. The racks on the sides are mounted with french cleats so they can be swapped out if I chose and each rack stores additional tools, centers, drill chucks, etc. There is a shelf inside the cabinet as well where I store tool rests, posts, chucks, etc.

Re: Tool Rack

#18

Alan Zenreich

Re: Tool Rack - tools

Alan Zenreich

Bernie,

Yes they are the Nano tools. I like them a lot. I got the original set then added a couple of handles and the round cutter.

Very nicely made and great for small hollow forms.