Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Shopsmith lathe

Posts

Shopsmith lathe

#1

Shopsmith lathe

john lucas

I was reading an article this morning in Woodwork on Mark Lindquist. He started his career turning on a Shopsmith. I did also. Not trying to compare the two of us just wondering how may others started on one.

After owning one for about 5 years and still turning on one at my Dad's I'm convinced the lathe is the weakest part of that tool. The tailstock is way too flimsy and of course fixed in position since you have to move the headstock and headstock quill to tighten the work.

The minimum speed is too fast and the machine too light to handle the size work that they claim will fit on it. They do make a very expensive device to slow the work down. I'm pretty sure Rube Goldberg works for them as a consultant.

The tool rest support is the weakest part. It's cast aluminum and very thin. It chatters like crazy and is a pain in the but to adjust if you have to move it. You need an allen key to adjust the swinging and the height adjustment is the same as the table saw.

Still, I did a lot of work, mostly segmented, with that machine and it got me into this world.

I don't think I would be the woodworker that I am without it. I had a complete workshop in the back bedroom of a 2 bedroom apartment. I sealed off the door and had filters over the airconditioning return ducts. This room was 8 by 10 feet and I could cut up a sheet of plywood by myself using outrigger supports I built. I had the planer, jointer, bandsaw and belt sander attachments that all sat on a stand in the corner when not in use.

I told all of the neighbors that if they heard any noise to call and I would stop immediately. They never called. Even when running the planer. Maybe they were Deaf. Although we did hear a really strange crashing noise one night and went to check on it. The neighbors had set up bowling pins and were bowling in their hallway. OK this wasn't necessarily on the good side of town. It was in LA as John Jordan says. That's Lower Antioch for those outside Nashville.

Re: Shopsmith lathe

#2

Re: Shopsmith lathe

Charles Watson

I did my first turning on one, and also first used it in a closed off room in the house.

It's still in my shop and since it gets used rarely, it's looking for a new home.

Re: Shopsmith lathe

#3

Re: Shopsmith lathe

john lucas

It's a great boring machine. I had to drill holes in the ends of 6 foot columns. They had to be square and I was heading to Atlanta to visit my Dad anyway so I took the columns. We clamped them to the table and extension table and used the quill feed to drill the holes. A 2 minute job. To do that at home I would have had to hand drill them and use some sort of jig to keep it square. Drilling into endgrain by hand isn't fun.

Re: Shopsmith lathe

#4

Steven Antonucci

not a shopsmith, but a craftsman monotube...

steven antonucci

Perhaps the easiest lathe in the world to exceed capacity on (you just put wood on it...), I'm not really sure if I took up turning or lathe repair. The headstock and tailstock were never aligned, so I was always turning multi- centered work (and made it really hard to make pens that fit right, since they were ovals).

When I sold the lathe, it was the happiest day of my life. Sadly, I "upgraded" to the other Crapsman 15" lathe, which seemed like it was going to be huge, but turned out to be even worse than the monotube. It made so much noise that I needed to wear earmuffs to use it. Owned it for less than a year before going to my current Nova. My Nova is still all OEM, except for the knockout bar that I lost...

I tell folks that it's not the lathe, but the turner... but in retrospect, you can't polish a turd. I wonder what the world's best piece ever made was on a Shopsmith? Or an old Craftsman mono?

Do you have any pics from back in the day?

Steve

Re: Shopsmith lathe

#5

Re: Shopsmith lathe

Don at Central Illinois

The main reason I bought my Shopsmith was for the lathe and the first thing I used after delivery. Didn't take long to realize it was not a lathe. Still sitting in the shop using it as a drill press for pens. Would like to sell it, but don't want to 'give' it away either.

Re: Shopsmith lathe

#6

Re: Shopsmith lathe

Phil Powell

Yup my start was on an old Shopsmith too. I bought for next to nothing, used

it as a table saw, drill press and a lathe. Wasn't much good at anything. When

we moved to Tn I gave it away. Really don't miss having it around.

Re: Shopsmith lathe

#7

Re: Shopsmith lathe

Fred Bearman

I started with the Shopsmith, still have it, along with my Jet Mni. Have given some thought to possibly upgrading to the new digital power unit (DVR). Not that I'll ever fit the category, but I've seen an awful lot of good work come off from Shopsmiths - I believe that Doug Stowe (flatwork - beautiful boxes, several books) started with the Shopsmith.

Fred Bearman

Port Huron, MI

Re: Shopsmith lathe

#8

Re: Shopsmith lathe

Ray Carson - Lawrenceville, NJ

I too started my woodworking on a Shopsmith. I only did one turning and honestly couldn't tell you what it was. I look back on my Shopsmith days and think, WOW !!! I actually had two SS's. One was my grandfather's that I inherited. It was old and really worn out. So I sold it. The other I inherited from my brother (took over the payments) because he lost interest in woodworking. He bought it to start a credit line. I sold that one through the early days of eBay to a military guy in Fredericksburg, VA.

I think the SS is a decent tool for an occasional woodworker / hobbyist. Most people I've spoke with say that they sold theirs after their skill level increased and the machine no longer fit their needs. This too was my case. My skills got better and changing the machine between tasks was a pain. I had to think 3 steps ahead so that changing the machine would fit into the project.

My 2 cents worth,

Ray :)

Re: Shopsmith lathe

#9

Re: Shopsmith lathe

bill Crommett

I have a different story about the Shopsmith. Mine is a model B from the early 50 s, and has served me well over the years. One thing a Shopsmith does that cannot be done with another lathe is when I turned a laminated three in. X six foot long railing for my daughters boat. It is now a dedicated disk sander that has been a life saver when doing segmented pieces.

About that six foot long railing: I removed the tailstock and bolted it to the shop wall, then blocked the rest of the machine back far enough to get my 6 ft long blank mounted. Things were a little whippey, but with a jack-built steady rest I got-er done.

Re: Shopsmith lathe

#10

Cut my turning teeth on a Shopsmith lathe

Mike Foster

I got started woodworking using a Shopsmith, including turning. I have to say that I made a lot of nice furniture using it. I also started my turning journey with a Shopsmith. My most prominent memory of turning with it was following the lathe as it danced across the floor with an out of balance blank. I probably pushed the limits of what it could, or more likely should, have done. I didn't really know any better at the time. I started my venture into segmented work on it for the same reasons that John mentioned.

I really miss the horizontal boring. That is one thing it did that was really nice, and hard to duplicate short of a dedicated machine.

I just read an article in Fine Woodworking about getting started in woodworking. The author made the case to start with smaller power tools that you can afford. They are adequate enough to enable you to do nice work. They also allow you the opportunity to figure out what you really want in a better power tool. I couldn't agree more. I did a lot of really nice woodworking with that machine, but I couldn't wait to replace it with real tools. Switching between modes became really annoying after a while.

Re: Shopsmith lathe

#11

Re: Shopsmith lathe

Jim Pugh

I also did my first 'turning' on a Shopsmith. Didn't have a clue what I was doing but used their tool set and their sharpening jigs. I also bought the speed reducer to bring the minimum speed down from 750 rpm. Did a couple of interesting staved umbrella stands on it for an acquaintance. Used it for other things as well but never used it for a table saw as I had a good Unisaw for that. Don't regret buying it and it served it's purpose at the time.

Re: Shopsmith lathe

#12

Bill Blasic

Re: Shopsmith lathe

Bill Blasic

The new Shopsmith is using the DVR motor from Teknatool.

Bill

Re: Shopsmith lathe

#13

Re: Shopsmith lathe

john lucas

Bill When you said DVR I assumed it was a motor and shaft like the Nova DVR. It apparently has a separate motor because it mentions belt drive. I assume it's a motor and controller similar to our current Variable Frequency drives and 3 phase motors. That's cool. It was needed on that machine. I had to clean my mechanical variable speed 3 times during the years I owned it.

Re: Shopsmith lathe

#14

Best Tools I ever owned.....

Barry Irby

Shop Smith and the Craftsman mono tube lathe, both tools beyond compare.

I bought the lathe when I was in high school and turned a lot of stuff on it. Many years later my son learned to turn on it. He was turning like a maniac and I was scrounging feverishly for wood. Went to a place where they made log cabin type houses hoping for some cut offs for him to turn. Guy and a Shop Smith that his buddy had soft there twenty years earlier. He tried over and over to sell it to me. I finally said "How much?". $20, I'll take it. Brought it home, cleaned it up, got it running, and painted it. Put it in the paper and sold it the first day for $400 cash and hundreds of dollars worth of stuff in trade. Used the Cash to buy a lunch box planer that I enjoy most days I am in the shop. Still using the Air compressor, sand paper, and clamps that came in the trade. Best part was that he had fifty or more blocks of hardwood that were roughly square and did not know what they were for, so he through them in. (Got those turning blocks I started looking for, In a second hand way)

Then I put the Craftsman lathe in the paper and sold it for m,ore than I paid for it thirty years before. Best tools ever. Never made anything on the Shop Smith, not the first cut. Wonder if it worked?

Re: Shopsmith lathe

#15

Steven Antonucci

That may be the best Craftsman story ever

steven antonucci

If it isn't some kind of fishing story...

When guys bring old lathes into the club. they can't give them away. I see them pack in, and then pack back out. I always thought I wanted a Shopsmith about 20 years ago, but I am glad it never came to be...

S

Re: Shopsmith lathe

#16

Re: That may be the best Craftsman story ever

john lucas

I almost bought a Craftsman round tube lathe. A gentleman had passed away and had the lathe in the paper. I went to his house. His widow showed me the lathe and some very worn short tools. He had made a living making bowls. There were bowls everywhere, most about 8" in diameter and 3" deep. It was mounted on a wooded table in a small shed and based on wear on the floor he spent a lot of hours there. It had 3 speeds, too fast, really fast, and probably light speed. I passed it up because I found an old cast iron Jay-line lathe that I was able to rebuild.

Re: Shopsmith lathe

#17

Re: Shopsmith lathe

fgvanatta

I started turning on a ShopSmith, and I still use it for larger turnings that won't fit on my Jet.

On the speed issue: get a speed reducer and you can get down to 100 rpm.

On the tool rest issue: the new Universal Tool Rest is fantastic, even if it is so heavy that it takes 3 men and a small dog to get it on the lathe. :D

As for the tailstock: I haven't found a solution for that. If anyone has one, I would be anxious to hear about it.

The ShopSmith is very versatile as a lathe, with the speed reducer, variable speed drive, and the fact that you can use it for reverse turning (off the back end).

Despite the knocks everyone likes to throw at it, I'm happy with this machine and use it constantly as a table saw, sander, drill press, bandsaw, and lathe. The only thing I found unsuitable about it is trying to use it as a router - it isn't fast enough.

Frank

Re: Shopsmith lathe

#18

Re: That may be the best Craftsman story ever

Barry Irby

It's not a fish tale. What I left out of the story is that at the time I tried to sell the Craftsman lathe I had somehow accumilated four lathes. The Craftsman monotube, an old Rockwell "school" lathe, a Delta Steel bed lathe, and a Nova DVR. I listed all of them in the paper except the DVR. The Craftsman sold the next day for $80, which was indeed more than I ahd paid for it. I offered it at the turning club meeting and someone shouted "Boat Anchor". There was NO interest in the other two and we ended up giving them away, one to a friend of mine and the other to a friend of my son.