Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Sanding Sealers

Posts

Sanding Sealers

#1

Sanding Sealers

Dave Gelnett

I have read that using a sanding sealer can dull the pop of the natural wood since it has some additive which can give the wood a slight haze appearance.

If this is true then what should I use since some wood has a very open grain and applying a lacquer finish can give a lot of tiny holes which takes forever to fix and forever is a very long time.

I would think thinning down shellac and using it as a sanding seal would work but my understanding is that shellac has a short shelf life. My one or two bowls a month would not be very practical.

Thanks

Re: Sanding Sealers

#2

Mike Mills

Re: Sanding Sealers

mike mills

I do use thinned shellac (2 parts DNA to one part shellac) as a sanding sealer.

For very porous wood (like oak) I take a different approach. I just coat the piece full strength and don�t worry about lap marks, minor runs, etc. I wait until it is just tacky (15-20 minutes) and dampen a towel with DNA. Then with the lathe running I give it a good rub down. The DNA re-melts the shellac almost immediately. The excess shellac is forced into the pores. I let it dry a few minutes again and rub with 4-0 steel wool on the lathe. If you still have open pores repeat but I would give it a few hours between the full strength.

Usually one application is enough.

I think shellac should have a shelf life of about a year if it is premixed, less if you mix it yourself.

Re: Sanding Sealers

#3

Re: Sanding Sealers

Dave Gelnett

Thanks Mike, so you buy the shellac pre mixed from the store?

Re: Sanding Sealers

#4

Re: Sanding Sealers

Bill Jacksonville, NC

If you want a lacquer finish, why not use lacquer sanding sealer. You can buy a commercial lacquer sanding sealer or used thinned lacquer.

Shellac flakes mixed with alcohol said to have a shelf life of six months. That can vary a bit based upon weather and humidity. Some Zinsser products not all claim a 3 year life, again that can vary a bit.

Lacquer & Shellac sanding sealers do add more depth to look and feel of top finish without masking wood.

Re: Sanding Sealers

#5

Jesper, Denmark

Re: Sanding Sealers

Jesper, Denmark

We have an ongoing discussion/experimentation on the subject of sanding sealers and bowl finishing here in DK in a local turning forum.

The base recommendation is to use a 1 lb cut of blonde shellac as a sanding sealer. That is 4 oz. of flakes to a quart of alcohol or 2 oz to a pint. If you use dewaxed shellac, you don't have to filter it.

The discussion on the shelf life and ease of dissolving the flakes center around the water content in the available DNA, which has 5-7% water. I have found a local source of Bioethanol in quart bottles. Since the bioethanol is produced as a fuel additive, it cannot be used as such with the 5% water content. So the bioethanol has had the water removed.

Normally, in my 40�F cold shop, it takes a few days for the shellac to dissolve in regular DNA. With the bioethanol, only 24 hours or so.

If ones concludes that the water has some effect on the shelflife of the mixed shellac, then the shelf life with the bioethanol should be better. In any case, the cost is relatively small, $3.00 for a quart of the bioethanol, so if you mix a small enough amount to last you 6 months, it's no big deal if you have to throw some away and make a new batch.

Re: Sanding Sealers

#6

Re: Sanding Sealers

Dave Gelnett

Is the Bulls Eye Shellac made be Zinsser any good? I saw it at the hardware store already made up. I read the label and was trying to make sure there was no wax but never saw the word wax in print. Went on line and the only talk about wax is on their sealer product but nothing on the can of just shellac.

Re: Sanding Sealers

#7

Mike Mills

Re: Sanding Sealers

mike mills

The Bulls Eye is the same brand I buy. You can buy the flakes and mix it yourself but I can't see any cost savings and does add the time and mess.

As other said you could also use lacquer and lacquer thinner. I'm just used to working with shellac and the smell of the thinner is not nearly as bad to me. Lacquer is fine over the shellac also.

Re: Sanding Sealers

#8

Chuck Jones - West TN

Re: Sanding Sealers

Chuck Jones - West TN

Jesper,

That is a good and thorough explanation and agrees with everything I have learned elsewhere... except if my shop was 40F, I'd build a fire or go to the house. :)

Re: Sanding Sealers

#9

Re: Sanding Sealers

fgvanatta

Zinnser's Bull's Eye shellac is great; their SealCoat is even better because it is dewaxed. It is dated on the top and has a 3 year shelf life.

Frank

Re: Sanding Sealers

#10

Jesper, Denmark

Re: Sanding Sealers

Jesper, Denmark

The shop is only 40� when I'm not out there doing something. There is an air handling unit, heated with hot water from the house hydronic system, which gets it up to a working comfort temperature in about 10 minutes.

The ceiling is insulated as well as the walls, so the uninsulated attick above is essentially at the same temperature as the outside - currently around 18�