Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Work holding survey-

Posts

Re: Work holding survey-

#26

Steven Antonucci

I use 1 1/4" concrete (Tapcon) screws

steven antonucci

They have the added benefit of countersinking into the face plates and leaving little piles of aluminum in every hole. If they can drill through concrete, they are going to be harder than the aluminum, no matter what grade it is. I run them in, then back them out, making sure that I haven't pulled the fibers up before redriving them.

If I look at the wood surface, you would imagine that it would leave a mark in the softer wood, but there never is one. I just tried a quick experiment with a piece that had a small ridge from a chainsaw cut, The far side was about 3/32" when I drove the opposite screw in, and I suspect that you are correct- the face plate probably didn't flex (I had some calipers and nothing changed dimensionally), but instead, the tapcon screw pulled so hard that it embedded the head of the opposite screw in even deeper.

Essentially, the screw used that little ridge as a leverage point to pull the high point down and since the low point couldn't move, the aluminum gave way in a game of rock, paper scissor (Steel screw beats aluminum by more than aluminum beats wood). I can post a picture of all of the aluminum shavings if you'd like to see them, but not tonight because I am sleepy.

If I tried this with a steel faceplate, it would snap the head off the screw if it didn't twist off first, since the screw wouldn't drill into the steel plate.

P.S. If you've never tried Tapcon screws, they are simply the best I've ever used. Nothing breaks them, the have a Robertson drive (square), and they are self drilling.

Steve

Re: Work holding survey-

#27

Leo Cuellar

In your opinion Wally...

Leo Cuellar

which species of wood is the best for a glue block? Us newbies need to know.

Thanks in advance,

Leo

Re: Work holding survey-

#28

Re: In your opinion Wally...

Wally Dickerman in Arizona

A fairly soft wood is best. Easier to part off. I use alder for a couple of reasons. Alder doesn't warp so it always had a flat true surface to make a good glue joint. I have a source for 4/4 alder lumber that is a full 1 inch thick.

Never use plywood or MDF. No strength and it might separate.

Wally

Re: Work holding survey-

#29

Jesper, Denmark

Re: Work holding survey-

Jesper, Denmark

I have three faceplates and two Stronghold Chucks.

I normally use the 4" Oneway faceplate for starting wet turning bowls and the chucks for everything else.

One chuck permanently has Jumbo Jaws mounted and the other usually the medium size jaws.

Re: Work holding survey-

#30

Leo Cuellar

Re: In your opinion Wally...

Leo Cuellar

Thank you Wally. I actually have a small stockpile from 1/2" to 2", have a friend who worked at a mill. Now I know what to use it for :)

Leo

Re: Work holding survey-

#31

Re: Work holding survey-

bill crommett from Seneca

I recently acquired a big , hardened by thirty years storage, maple burl that had to be cut down considerbly to fit on my big General. For such big stuff I like to use a big faceplate, and I found in the tool pile a new green 6 inch faceplate, unused-ever.

The interesting part is that two of us spent twenty minutes trying to mount the chunk on the spindle before we discovered that the reason the faceplate looked so new was that it was a left hand thread for outboard turning. Duuh !

Re: Work holding survey-

#32

Spence

Re: Work holding survey-

Spence

1 chuck and 1 faceplate

The chuck is the vic mark 120 with 3 sets of jaws. It was the main chuck I used on my old PM3520 and is now mounted on my Rikon mini. Talk about over kill?

The face plate is a 3" that came with the Rikon and I try to use it as much as possible to turn the outside of the blank and make it as light as I can before mounting it in the chuck.

Would love to use glue blocks but don't have the right kind of glue. All I have on hand is PVA and the only wood is really green cherry and some soaking wet crab apple. Don't think the Titebond would hold it safely.

Before the big disaster the count was 4 chuck and about a dozen different face plates...