Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Sioux drills

Posts

Sioux drills

#1

Sioux drills

Randy Johnson

>Within the last week I posted a question about the Grex ROS. In his reply, Bill Grumbine mentioned his drill named Sioux.

For those of you who do not already know it, Sioux is no longer making any of its small right angle drills. There are a few internet sellers who still advertise them, but both Packard Woodworks and Highland Hardware told me that they are no longer available.

What�s more, the nearly identical Milwaukee seems to be gone as well. That�s what I did have and I was just going to get another one. However, in trying to check prices before I made the trip to Richmond�s (IN) Lowe�s tomorrow I have discovered that nobody lists it anymore. Not even Milwaukee. It seems that the choices are down to one, DeWalt. That might not be so bad, because from the picture at Amazon it looks like the DeWalt lacks the venting towards the front of the drill that did such an excellent job of sucking in dust with the Milwaukee.

For the record, what killed the Milwaukee seems to be a bearing that seized on the shaft. Instead of the outside of the bearing remaining stationary it must have been spinning with he motor shaft and ate the plastic housing it rested in. I blew it out regularly while using it but it still had an incredible amount of gunk in it when I took it apart.

Re: Sioux drills

#2

Re: Sioux drills

Harry in Beautiful Downtown Kulpsville

>Another alternative is Harbor Freight. They sell a cheap right angle drill that isn't great but works. And, it is cheap enough to throw away when it dies.

I've also heard that replacing the bearings in any of these drills with sealed bearings will greatly extend their life. Never tried it and don't know any more about it but it does make sense.

Have a great Thanksgiving!

Re: Sioux drills

#3

Ellis Walentine

Thanks for the tip.

Ellis Walentine

>I'll have to pay attention to the dust-in-the-bearing situation with my Milwaukee. That thing cost too much to let go so easily. It's always something.

Ellis

Re: Sioux drills

#4

Neiko and Kawasaki drills

Doc Green

>Here are two different drills that have the angled head similar to the Sioux. Both appear to be "disposable." I don't really know anything about either of them.

Google "Neiko right angle drill" and "Kawasaki right angle drill" and you should find them quickly. Amazon has them.

~Doc

Re: Sioux drills

#5

Re: Sioux drills

D. Hansen

>Randy Milwaukee still makes the close quarter drill. It has a different grip but is the same drill. Souix was made by Milwaukee by the way. The front bearings on both are embedded in grease. The rear one though is not. That is the culprit. It can be replaced if the housing is not worn. I not only blow the drill out but cover the exhaust ports with the filter material Lowe's has for putting in your A/C heater floor vents. The sealed bearings for the rear can be found at Boca Bearing in Florida. They are a bit tricky to replace but can be done. By the way the new Milwaukee close quarter drill has a new model number and the housing looks more streamlined.

Re: Sioux drills

#6

Sears

Steve in NC

>Sears still has the Milwalkee listed for $117.00

Re: Sioux drills

#7

Re: Sioux drills

Randy Johnson

>I thought the Sioux and the Milwaukee I had looked a lot alike. Now I know why. Whatever I get to replace the Milwaukee I will try the filter idea. I hate to admit it, but I never would have thought of doing that.

Re: Sioux drills

#8

harbor freight disposable for 29.95

bob davis5098

>

Re: Sioux drills

#9

Re: Sioux drills

Nick Tuzzolino

>Not sure I follow. I just blew my Sioux out. Top ports were filthy, bottom ones not so. If the exhaust ports exhaust, how does covering them help?

Re: Sioux drills

#10

Jerry Louden

Re: harbor freight disposable for 29.95

Jerry Louden

>Been using the Harbor Freight drill for 5 years now and still going strong. Great little drill. Suppose it will go bad now that I have bragged about it. Murphy's law.

Happy Thanksgiving to you all.

Jerry

Re: Sioux drills

#11

Re: Thanks for the tip.

Jorge Castaneda~Downeast Maine

>Ellis,

A few years ago Terry Daniel told us about the sizing problem and suggested replacing the bearing with a better one, a search should bring it up. It is good info for people with the Milwakees.

Jorge

Re: Sioux drills

#12

Re: Sioux drills

D. Hansen

>Nick one side seems to be intake the other exhaust. I reverse the direction so maybe that is not correct. Anyway I just tape the filter material over the ports on both sides and replace them when they get dirty which is very frequent. Even though I run the drill for long periods I have never had it heat up with the filter in place which is one thing I worried about.

Re: Sioux drills

#13

Re: harbor freight disposable for 29.95------WebKi

Brian McKearney------WebKitFormBoundary+A8EzS8593K

>I agree with the votes for the Harbor Freight "disposable". I bought one of the premium Sioux drills that were sold by Craft Supplies and it was a great drill. Then it started to show signs of wear due to dust and I replaced it before it died with one of the "disposable" close quarters drills from Harbor Freight. I decided to keep the Sioux as a "premium" drill for my shop and now use the Harbor Freight exclusively for turning/sanding - works great and if it dies, then I would have gotten my money's worth because it's cheap!

I'd recommend spending less money on a cheap drill for sanding - works just as well and then you won't feel bad when it dies due to abuse from sanding dust.

My link didn't work, but I had the model ITEM 92956-1VGA from Harbor Freight that currently sells for $36.99.

Brian

Re: Sioux drills

#14

Katherine Kowalski

Re: Sioux drills

Katherine Kowalski

>I must say that all this talk about "disposable" tools is somewhat distressing and disheartening.

While it may be "cheap" to buy 10 or 15 drills from discounters, it is the environment that pays the price. Just think about what happens to all those thrown away drills -- they don't biodegrade very well...

The cost too is to our society -- if we keep buying "crap," the manufacturers will continue making it.

We're turners, craftsman. By our very occupation, we believe in using renewable resources. I, for one, believe in buying the very best tools for turning, and a higher quality incendiary tool, because it will last me a LOT longer than these so-called "disposables."

Before you shell out money for something you already know is going to break -- think about it. And think about the legacy you are leaving (and teaching) your children and grandchildren, your students, and all the rest of the folks you might inspire one day.

Re: Sioux drills

#15

Re: Sioux drills

Juergen

>My cheap Harbor Freight drill lasted longer than the $150 Sioux

Re: Sioux drills

#16

Re: Sioux drills

Dave Moore

>Katherine, in principle I agree a hundred percent.

The problem with these close quarters drills though is that they are not designed (none of them) for the beating woodturners subject them to.

Consequently it's not uncommon for a cheap "throwaway" to last as long and sometimes longer than a $150 model. (sometimes they last ten minutes too, but almost always the vendor will replace it)

On top of that, they are pretty much all made offshore, often in the same factory, regardless of "brand".

I love quality tools, I think most craftspeople do, but it's getting harder and harder to find them especially in the handheld powertool category.

To my knowledge there aren't any handheld units that are designed to handle what we want them for, electrical ones anyway, and even the pricey ones often blow up quite quickly.

It's a tough problem when paying the extra money doesn't ensure a significantly longer service life, and it's hard to be critical of anyone unwilling to do it.

I wish it was different, but it's not.

A shame, but there it is.

Re: Sioux drills

#17

Re: Neiko and Kawasaki drills

Bill Neddow------WebKitFormBoundary+w+uCg3oRve3I+f

>I find the Neiko drill last at least twice as long as the Sioux brand and is cheaper to buy new than it is to repair the Sioux.

The problem with the bearing in the Sioux has been known for years, yet through several "redesigns", the company has refused to address the problem. If they have lost the market for the tool -- they have brought it on their own heads. Here in Canada, the Sioux (Milwaukee) was way too expensive -- almost $250 with tax. I buy the Neiko for $60 -- less, if on sale.

I love to buy good tools. But, in this case, the quality of manufacture did not match the price.

Re: Sioux drills

#18

Re: Sioux drills

Nick Tuzzolino

>Darryl: Now I get it. Thanks for the reply and many thanks for the tip.

Nick

Re: Sioux drills

#19

Re: harbor freight disposable for 29.95------WebKi

Jeff Brockett

>I have had good luck with the same harbor freight right angle drill and the cheap air powered harbor freight dril ($19.99 on sale!)

Re: Sioux drills

#20

Re: Sioux drills

Bill Grumbine (Kutztown PA)

>Since my name was invoked here...

I have owned my Sioux drill for about seven or eight years now. I have a reputation for being hard on things. I don't abuse them (most of the time) but because of my size, stuff just wears out faster. This is true for anything one might care to name. Tools fall into that category. I can exert "normal" pressure and have something break, where the same thing would last another person for years.

I write all this to set up the picture. I use my Sioux drill pretty hard. I blow out the dust when I think about it. But in all the years I have owned it, I have only had one problem, and that was the switch breaking a few months after I bought it. They replaced it under warranty, and it has been running strong since. There is no hint of bearing problems with it that so many others have described. Maybe I got a bad one?

Katherine, I agree with you that we are to be good stewards of what we have. But when people write "throw away", it is because a HF drill costs about the same or less than fixing the bearings on a more expensive drill. It is unfortunate that things have gotten that way. In my classes, I recommend the cheaper drill to start. It is not like anyone buying it for this type of work needs a precision chuck with little runout. In fact, runout might help! But even with all that, when my trusty Sioux breaks, I will most likely pay up to have it fixed. It has been a good tool, and I hate to toss a tool with a good record in favor of an unknown quantity (or quality!).

Re: Sioux drills

#21

Wayne K

Re: Sioux drills

Wayne K

>I too love quality tools. I buy quality tools when I am going to use them for what they were designed to do. Drills are designed to drill holes, not long periods of sanding bowls and getting filled with wood dust.

I too use a harbor freight drill to fill with wood dust. I cannot bring myself to abuse and destroy a quality tool such as a millwaukee, by sanding with it for long periods of time.

Re: Sioux drills

#22

Re: Bill- I twice paid for a Sioux drill....

Jamie Donaldson

>...repair, and both times it was returned to the "authorized" repair facility for repair damages. The second time I was showered by wire shavings as the armature wrappings shredded, so unless I can repair items like bearing replacement myself, I don't send many tools out. This only adds to the replacement/repair dilemma, because competent repairmen are few and far between in many areas these days.

Re: Sioux drills

#23

Re: Sioux drills

Barry Irby

>It seems to me the problem is poor Engineering. For this drill and many of the things we buy. If they were designed to be simple to repair and simple to deconstruct we could repair them until it was no longer practical and then return them to the manufacturer for deconstruction. If they could reclaim the materials out of the item economically, would that likely be the raw materials for the next thing they want to build?

Of course, using a drill as a sander is clearly abusing the tool, asking it to do something not considered by the designer.

Re: Sioux drills

#24

Re: Bill- I twice paid for a Sioux drill....

Bill Grumbine (Kutztown PA)

>Wow Jamie, that's rough! Like I wrote, mine has been pretty much trouble free, and the main reason I sent it out was it was still under warranty. It even came back with a seal on it with the date and a number or something to show that it was opened by a factory authorized dealer and not by me.

Re: Sioux drills

#25

Re: Sioux drills

Randy Johnson

>The main reason I started this thread was that I thought you probably used yours at lot more than most people and that it spoke volumes for the quality of Sioux drills. That�s why I considered it first as the replacement for my Milwaukee. I was disappointed that it is no longer available. I figured that if it was that reliable it wouldn�t be getting replaced very often and people who have them now might not notice the disappearance from catalogs. It was kind of a �heads up� post.

That, and I really enjoyed your play on words.