Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

It has begun...

Posts

It has begun...

#1

It has begun...

Thad Parker

>...the 70 year-old beast, my circa '39 J.A.Fay & Egan model 400 lathe, has begun to falter.

Investigating a noise, i discover the following:

the original belt has finally given up the ghost.

I can't attempt to dismantle it tonight, but my FIL told me when he gave me the lathe that he had done maintenance on everything except the belt/pulley b/c he could not figure out how to get to it.

Anyone know of a link-type belt I might replace it with?

~ Thad


img

Re: It has begun...

#2

Re: It has begun...

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>Finish the break, then post the dimensions, would probably make the work on this side easier.

Re: It has begun...

#3

belt size

Thad Parker

>30-7/8" long

1-1/2" wide (outside)

1-9/32" wide (inside)

approx 13/32" thick

number on the belt is: 2530V300 01

Re: It has begun...

#4

Re: belt size

Jeff Willaford

>Google belt 2530V300 01 Quite a few listings show up claiming that is a standard belt. You can check each one for the phone number to see if that particular belt is still available.

Re: It has begun...

#5

Re: It has begun...

Bob Ingram

>You can get replacement belts custom made. I used to have a shoe repair (lathe) machine that used that type of belt. I googled conveyor belts..... If that belt held up that long why throw out the baby with the bath water?

Re: It has begun...

#6

Re: It has begun...

Pete in Holland, MI

>If you live near a bigger city, look for an industrial belting company, power transmission supplier, or watch the area for an antique tractor club and one of their swap meets.

I have a Clipper style belt lacer if you find the material but can't find someone to lace it together.

Pete

Re: It has begun...

#7

Staples

Jorge Castaneda~Downeast Maine

>Thad,

Those belts are stapled , just thread a leather strip of the right dimensions and staple it together, look at the existing staple, if I remember correctly the belts are not very tight either.

Good luck

Jorge

Re: It has begun...

#8

Yes Jorge,

Thad Parker

>the belt fits quite loosely. I'm not sure I understand what you mean about it being stapled. Looking at it, I do not see anywhere that appeared stapled; at least not any stapling process I am familiar with.

I was hoping to be able to replace it with some kind of linked system, due to the apparent difficulty with gaining access to the pulley...but as stated in the original post, that is hearsay from my FIL.

Good to know it is still available though.

~ Thad

Re: It has begun...

#9

Re: Yes Jorge,

Bill Crommett

>Thad: If all else fails, look up a sawmill products supplier. That is where I got a new belt and stitching for my old South Bend Machinists lathe that used a flat belt.

Re: It has begun...

#10

In searching for replacement... *LINK*

Thad Parker

>...I came across a GoodYear pdf (linked below).

The original belt was "molded construction," but their footnote indicates molded construction belts were not made after '06.

I may be able to still find one, but would it suffice to use a "cut-edge construction" belt as a replacement?

~ Thad


GoodYear PDF on vs belts

Re: It has begun...

#11

Re: Staples

Joanne in Point Pleasant, PA

>Does it look like this? This is the belt on my 16" jointer. It is a wide belt with staple-like items on the ends and a thin solid plastic tube that goes through them (sort of like a hinge pin).


img

Re: It has begun...

#12

Roger in MO

Re: It has begun...

Roger in MO

>I have an engine lathe with a flat leather belt. The ends are held together with rawhide lace. I believe this was very common years ago.

I have a diagram of the lacing pattern which I'll be glad to send to you if you provide an address.

Roger in MO

Re: It has begun...

#13

nope

Thad Parker

>it looks like a standard constructed belt

Re: It has begun...

#14

That'd be great...

Thad Parker

>...can you email me so I can reply with my address?

~ Thad

Re: It has begun...

#15

Re: Staples

Jorge Castaneda~Downeast Maine

>Hi Joanne,

That is exactly what I remember from my technical school days. Yes the pin can be drawn out and the belt cleansed or oiled and then reassembled.

I am jealous, you have a 16" joiner! :o)

Looks like Thad's belt is a newer version...

Re: It has begun...

#16

Re: belt size

dick strauss

>Thad,

It looks like there is a cross refernce to Gates PN 98000521 on the following site. It also looks like they have your belt for sale. http://shop.limct.com/?page=shop/flypage&product_id=5746&category_id=61064f7b81acb4d096f29c24a379b1cd&PHPSESSID=f5ced4aa6a5e9ff3e2545f8569a1f42e

If not, it looks like a modern motorcycle or snowmobile drive belt. You may want to pursue this option as well.