Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Oneway Vari-grind jig

Posts

Oneway Vari-grind jig

#1

Oneway Vari-grind jig

Ray Binnicker

>OK, I've read the instructions, I've watched the free video at their web site and I still don't understand how/why/when/ you adjust the leg on this thing. I "picked" a location and it seemed to sharpen pretty good. But, there has to be a reason for all the different slots to place this leg.

Help.

Ray Binnicker

Re: Oneway Vari-grind jig

#2

Re: Oneway Vari-grind jig

Jim Pugh, Elyria, OH

>Ray, I believe the adjustments are so you can set up your jig to grind the tool the way you want it. After that you will seldom move it. Mine stays between the second or third notch (mark in my case) and I only move the leg if I'm experimenting with a grind.

Re: Oneway Vari-grind jig

#3

Re: Oneway Vari-grind jig *LINK*

tek-Brunswick, Ohio

>By changing the angle of the leg you vary difference between the nose angle and the angle on the side grind. Many turners use one angle for bowl gouges and a different angle for spindle gouges. I use the same angle for both. I only need to set the nose grind by sliding the arm. Turners have different grinds they swear by. I think it is mostly what you are used to. If you stick to the common angles for gouges, around 40 deg for spindle gouges and around 55 degrees for bowl gouges you should be fine. An angle that is too acute, say less than 35 degrees, is hard to control. An angle that is too obtuse, Say more than 65 degrees, may not cut as cleanly or quickly. A common mistake is to have the side grind at to acute of an angle. Here is a link to Doug Thomson's sharpening instructions for the wolverine jig. It is a good all around setting for a tarting point. If you can get your hands on the AAW sharpening DVD it explains a lot very clearly.


Thomason Sharpening

Re: Oneway Vari-grind jig

#4

Re: Oneway Vari-grind jig

Ray Binnicker

>Thanks guys. I wish Oneway had been a little clearer with the instructions. I'm going to the link you gave and then back to the shop.

Ray Binnicker

Re: Oneway Vari-grind jig

#5

Re: Oneway Vari-grind jig

Rick Allen

>If you can get someone to give you a little hands on instruction you will be an expert in less than 30 minutes. Most local woodturning club members would be happy to show you have to sharpen using the Oneway jig.

Re: Oneway Vari-grind jig

#6

Oneway Vari-grind jig: Set leg at 23 degrees

Jerry Hall

>Kirk DeHeer,an instructor at Craft Supplies, wrote and article in the Winter 2006 AAW Journal (I think) on setup and use of the jig. Very well done. The most striking recommendation was to set the leg at 23 degrees and forgetaboutit. He stated this comes closest to mimicking a well done hand grind by the pros, maintaining a side angle that about equals the nose angle. He demonstrated at Portland.

I have been surprised that there has been no discussion of his recommendation, and would like to see some. I have been using it for several months and like the results and the simplicity. I don't think a new turner can go wrong with this approach. He also includes a nice setup jig for repeatable bevel angles. You can buy a single copy of the journal from the AAW, but double check the volume number.

Re: Oneway Vari-grind jig

#7

Re: Oneway Vari-grind jig: Set leg at 23 degrees

john lucas

>There will also be a good tip on setting up the Oneway system in the next issue of American Woodturner.

Re: Oneway Vari-grind jig

#8

Confusion re angles

Dinyar Chavda

>What always confuses me is how the angle is meant to be measured--is it from the horizontal, or is it from the vertical. I have to consciously think about it every time someone talks about these angles.

In fact, if you look at the Thompson link mentioned by tek, in the chart, the bowl and spindle gouge angles are measured from the horizontal, while the scraper is from the vertical! Why?

Do you think I may have inadvertently come up with something new for the AAW to debate (a la the proper name for the roughing gouge)? :-)

Re: Oneway Vari-grind jig

#9

Re: Confusion re angles

john lucas

>If you use the rough out gouge for turning bowls do you measure the angle from the handle line or from the bent tang line. :)

Re: Oneway Vari-grind jig

#10

Re: Confusion re angles

Doug Thompson near Cleveland

>Confusing isn't it. Like measuring a bowl gouge is it the flute width or diameter... That's the way things are.

The scraper is sharpened on a platform, it's easier to discribe as a 20 degree angle ( tilt the platform 20 degrees ) then to say it's a 70 degree angle. Tell your friends you use a 70 degree angle on your scraper. It's not a lie but it sure sounds crazy.

Now the skew is a included angle... Hummm

Re: Oneway Vari-grind jig

#11

Re: Confusion re angles

Dinyar Chavda

>Doug:

I didn't comment about the skew, as I can understand that being an included angle, but why does one go from the horizontal to the vertical when going from 60 (for the gouge) to 70 degrees (for the scraper)? Oh well, one more instance to repeat the mantra of Vinnie Barbarino!

D

Re: Oneway Vari-grind jig

#12

Re: Oneway Vari-grind jig

Doug Thompson near Cleveland

>tek thanks, the leg angle is very hard to discribe and if it's not close the grind might not work as well. Oneway allowed me to photograph my jig (full size) now a person can place their jig on the picture to set the leg angle.

I can not say enough about the Oneway wolverine it works so well BUT for my own personal tools I freehand the grind. Go to the Buckeye meeting this month if you need a good laugh, with all the talk about the perfect nose and side angle I'll show everyone it doesn't matter. Close enough works just fine. I remove the bevel on a 36? grit wheel. If I don't get nervous it can be done in 20 seconds. This is my first club demo.

Re: Oneway Vari-grind jig

#13

Re: Confusion re angles

Doug Thompson near Cleveland

>I really don't know why it's like that... only our turning fore-fathers know for sure. Hopefully someone can chime in with a reason.

Re: Oneway Vari-grind jig

#14

Doug Demo *LINK*

Gordon Seto

>Doug is going to demo at our Club on full size cowboy hat and thin wall turning at out next meeting. The demo is scheduled for 3 hours. He promised to show all the details. It will not rushed through like a rotation at the symposium.

I think he may have his Thompson tools available also. This is your chance to examine the best value tools in person.

Demo details:

Buckeye Woodworkers & Wood Turners

3rd Saturday August 18th morning at 9:30

Usually members arrive at around 9 for donut and coffee.

Visitors are welcome.

You can find the detail at:

http://bwwt.org/

Gordon


BWWT

Re: Oneway Vari-grind jig

#15

Ditto on the Kirk DeHeer article. Should be

david

>madatory stuff for any turner who doesn't sharpen freehand. Try it--you will like it.

Re: Oneway Vari-grind jig

#16

Re: Confusion re angles

Arch

>Hi Dinyar.

You confused? I can't believe it. Probably just another of the ups downs and sideways of woodturning and a rose by any other name, etc. BTW, shouldn't the purists call the tool a spindle _smoothing gouge? Altho in my case, the blank often ends up rougher than before. :)

Arch

Re: Oneway Vari-grind jig

#17

Re: Oneway Vari-grind jig

Mark Kauder, Phenix City, AL

>I noticed that everyone is talking about the angle on the Jig, but there are two other measurements that have to be constant if you are all going to talk about what Jig angle to use.

The other dimentions are the distance of the back of the pocket that the jig goes into from the face of the grinder wheel, and the distance that pocket is from the centerling of the grinding wheel.

Example, set the jig to where you want it, now move the pocket it sets in, in or out from the grinder an inch or two.

My understanding is, that the distance that the pocket is from the grinding wheel set the side/wing angles, and then after that, adjusting the angle on the Veri-grind will establish the nose angle.

Maybe I am missing something.

Mark

Re: Oneway Vari-grind jig

#18

Re: Oneway Vari-grind jig

Mark Kauder, Phenix City, AL

>OH, OH, OH. Third dimention - distance of the tool extended from the Jig. That must also remain constant.

Mark

Re: Oneway Vari-grind jig

#19

Re: Oneway Vari-grind jig

Arch

>Hi Mark,

...and the fourth dimension is Time. The time it takes to adjust a sharpening jig, but no doubt it's worth it. Yep, some of my puns smell even worse than my others. Sorry. :)

Arch

Re: Oneway Vari-grind jig

#20

Re: Oneway Vari-grind jig

Gordon Seto

>"My understanding is, that the distance that the pocket is from the grinding wheel set the side/wing angles, and then after that, adjusting the angle on the Veri-grind will establish the nose angle."

Which changes which is not important, and they are just some of the variables in setting the Varigrind jig.

For the sake of argument: If we are just using the pocket (not using the Varigrind) when sharpening SRG and traditional grind bowl gouge, the distance of the pocket sets the nose angle. That is very close to setting the Varigrind at the top notch. There is no side grind. We move the pocket closer, the nose has a steeper angle. Every notch we move the leg towards the bottom, we can get a longer side grind. If we lock down the leg to the bottom position, we can get all the nose angles by moving the pocket in and out but they all have very long side grinds.

I know what I say is opposite to what the sharpening DVD said.

Just as I said, the terminology is useless. The only things that matter are the right combination for your style of using your tool.

I don't think there is a magic tool and grind that will fit every turner. Mike Mahoney, Stuart Batty and David Ellsworth are some of the best bowl turners. Richard Raffan, Nick Cook and Alan Lacer are skew masters. They don't even agree on the best tools and have the same grind. Probably none of them is setting the jig at 22.3776� or most are not using the jig at all; I doubt they would reach another level by doing so either.

Gordon

Re: Oneway Vari-grind jig

#21

Re: Oneway Vari-grind jig

Mark Kauder, Phenix City, AL

>Excellent comments.

Yes, I have mine set and use whatever that setting is for most of my gouges, and just never mess with it.

Above, Arch mentioned Time. Mostly in jest, but that is a factor. With all the same settings, you can change the shape if you over/under grind the tip, compared with the wings. The tip, with less metal in contact with the wheel, will generally grind away faster with a given pressure, than will the wings.

Mark

Re: Oneway Vari-grind jig

#22

Re: Confusion re angles

Dinyar Chavda

>Hi Arch:

You'd think that they would've called it a smoothing gouge as opposed to a roughing gouge, wouldn't you, just to make things clear?

Reminds me of the Archie Bunker episode, where Edith is trying to get Archie to eat some salad, on the grounds that it has roughage, which is good for him, and Archie's classic response: "Edith, at our age, we don't need roughage, we need smoothage!"

Re: Oneway Vari-grind jig

#23

One thing to remember....

TDaniel

>All that any of the sharpening jigs will do is give you a nose angle and a final side angle.....everything between these is "hand/eye" coordination. Another thing to remember is that the steeper the sides, the higher the cutting edge will be. If the cutting edge is higher than the equator of the tool you will have a tool that is highly prone to nasty catches. Basically, with high sides you can only cut with the nose of the tool.

Re: Oneway Vari-grind jig

#24

Re: No more confusing facts TD! Most...

Jamie Donaldson

>.. of us don't need to know all the exact heel and toe angles, and now you throw in an "equator" on a tool?? We can't change it, so don't worry about it- too much information!!!! ;-))))

Re: Oneway Vari-grind jig

#25

Re: Confusion re angles

Russ Fairfield

>Hey, I can remember when it was called a "Rounding Gouge" because its primary uses was to make square things round. That still makes more sence to me.

There is no confusion of the anglrs when we use the correct terminology. "Relief Angle" was the term that I learned to use when describing the angle of the metal that had been removed from the nose of the tool. "Tool Angle" was used to describe the angle between the surfaces that remained. I think the confusion comes because the words "relief" and "tool" are no longer used.