Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Oneway Vari-grind jig

Posts

Re: Oneway Vari-grind jig

#26

Re: One thing to remember....

Mark Kauder, Phenix City, AL

>T.D. What you say is true, but this is true of any gouge that has wings that go above the flute of the gouge. And true if you are cutting with the top cutting edge with the bowl gouge rolled to one side.

Mark

Re: Oneway Vari-grind jig

#27

Oh yes you can....

TDaniel

>When you sharpen a bowl gouge so that the sides are a steep angle it moves the cutting contact point higher. When the point moves above the centerline or equator problems arise. Remember, all parts of the gouge above the equator rotate right to left.....all parts below the equator rotate left to right. Whenever the tool hits some grain that it cannot cut do you want it to rotate into the wood or out of the wood? This is the basis of most catches. We have a choice; we can let the tool back out of a cut or we can let it dig in....the choice is ours.

Re: Oneway Vari-grind jig

#28

Re: Confusion re angles

eliot d

>You have every right to be confused about this. In every right triangle, there are two acute angles that are complements of one another, and turners often do not define which angle they are talking about. Talking about vertical or horizontal really doesn't help unless you know if you should picture the gauge itself in the vertical or horizontal position. I find the easiest way to think about it is to know that a perfectly square edge would be said, by woodturners,, to be a 90 degree bevel -- not a zero degree bevel. So, if someone is talking about a "steep" bevel, he means something closer square, e.g. 80 degrees. If you hear , say 20 degrees, that would be considered a quite shallow bevel , not at all close to the 90 degree square end. (Personally, I think the convention is backwards because I think a square-ended tool should be considered to be zero degrees; after all, you wouldn't have to grind away any metal!) I wonder what metal workers have to say about it.

Re: Oneway Vari-grind jig

#29

Re: Oh yes you can....

eliot d

>I find your post confusing when you talk about "rotating right to left" or "left to right". Are you thinking of a bowl? Inside or outside? Also,by "steeper" you should mean closer to a square;i.e. removing small amount of metal. Is that what you meant? Some turners might think that "steeper" meant more grinding, which is not what I think you meant. Almost certainly, for this kind of stuff pictures are best.

Re: Oneway Vari-grind jig

#30

Re: Confusion re angles

HarryB in Kulpsville

>Dinyar,

In the Stewart Batty and Mike Mahoney video they are quite specific in measuring the angle. It is measured from the flute and across the bevel. This works for everything but the skew and if I remember you feel the only time a skew should be used is for stirring paint! :o)

Re: Oneway Vari-grind jig

#31

Re: Oh yes you can....

TDaniel

>Steeper is a more acute angle. As the angle of the sides becomes more acute the cutting edge goes higher; once it gets above the centerline of the tool the cutting edge will rotate into the wood rather than out of the wood in the event that you hit tough grain. Remember, cutting is just like mowing your lawn.....if you get to the area above the field line of your septic tank you must take a lighter (narrower) cut or you will choke the mower down.....same way with the gouge. The gouge, if used properly, can rotate out of the wood when hitting the tough grain....used improperly it will rotate into the wood which will make a nasty catch. I go into the physics and geometry of this in my "Catch Free Turning" demo. It really does matter how the gouge is sharpened.

Re: Oneway Vari-grind jig

#32

My use of the skew

Dinyar Chavda

>Actually Harry, I've found that it is perfect (when laid down flat) for making the dovetail on the tenon for my Vicmarc chuck!

Re: Oneway Vari-grind jig

#33

Re: One thing to remember....

Charles Watson

>I tried the 23 degree setting on the vari-grind yesterday and it seems to give those steeper sides especially when compared to the Ellsworth grind. So, does that mean the 23 degree is not best? Hope to hear from others on their experience with the 23 degree.

I do know that I'm wearing out more gouges experimenting than I am sharpening from the wear of use.

Re: Oneway Vari-grind jig

#34

Re: One thing to remember....

Gordon Seto

>If the Ellsworth grind works for you and you are happy the results, there is no sense changing it. With a different grind, you change the gouge presentation angle to wood.

Don't make the mistake I did. After watching each professional demonstration, I change my grind to follow that demonstrator. Of course, I didn't get any improvement except my gouges were shorter.

I belong to two active Clubs and have been to several symposiums, I have seen quite a few nationally known professional demonstrators. I noticed they all have different opinions on their tools and grinds. Obviously they all work very well for each of them. Now I believe their universal magic bullet is practice.

Re: Oneway Vari-grind jig

#35

Mostly correct....

TDaniel

>A lot of the variety in angles is related to handle position. I use a low handle style and cut with the side of my gouge instead of the tip. I know others who do most of their cutting with the tip or nose of the gouge. If I were to make a hat I would use the tip for that project but for everything else I use the side. I have seen demos by some nationally known turners where it was obvious that their notoriety was from their end product and not their method or tool skills. That is what made the Gathering so much fun. We had an opportunity to try different ways of doing things as well as trying each other's tools. You get a bunch of turners together and somebody's gonna learn something!

Re: Oneway Vari-grind jig

#36

Re: Mostly correct....

Gordon Seto

>TD,

I totally agree with you. I think gouge grinds and the way to use the tool go hand in hand. My point was the whatever degree angle setting on the Varigrind jig was just a guide line.

With the help from Doug of Thompson tools, I have experimented with his "V" and "U" bowl gouges on grinding with Varigrind. Under identical settings, I see two very different side grind angles.

Someone said at Craft Supply classes, they have their jigs welded at the 23�. Obviously, that is an angle within usable range. But I believe the main reason for welding is to minimize their gouges wear in their class setting.

Trying out at gathering is much better than I watching. I can't imagine the good that will come from just changing the jig without even discussion on how to use the tool.

Gordon

Re: Oneway Vari-grind jig

#37

Re: My own setting on the ....

Jamie Donaldson

>...Wolvering jig is nothing close to 23 degrees, but more like the setting Doug Thompson illustrates on his jig. There are so many variables with this set-up that what works for one will yield quite different results for another. Don't practice grinding on a HSS gouge to explore grind angles- use a bolt or some other piece of scrap steel which has similar dimension to your gouge, then once you find the approximate settings reach for the real thing!

Re: Oneway Vari-grind jig

#38

Re: My own setting on the ....

Mark Kauder, Phenix City, AL

>Good points, Jamie. Especially about practicing on a cheap piece of steel.

Somewhere when I first got my Wolverine/Veri-grind, I read that the pocket of the arm should be 4" below the center of the grinding wheel, and 7" out from the front face of the wheel. The gouge should be 1.75"-2" out from the jig, and then make your adjustments. I did, and have not really changed them since. I even drilled a hole through the two adjustable plates, and put a small bolt through it so that I could always go back the that setting if I was to ever play around with it. And I don't much.

Mark

Re: Oneway Vari-grind jig

#39

Re: Oneway Vari-grind jig

eliot d

>I've recently been using the Ellsworth jig for all my swept back gauges. For those who use a Tormek, if you set the Turning Tool Setter to JS=4, alpha=55 degrees, and P = 55mm, you'll get the same grind on the Tormek. So a good way to sharpen is to use the Ellsworth jig to shape the tool and then switch to these settings on the Tormek to really get it sharp.

Re: Oneway Vari-grind jig

#40

Re: My own setting on the ....

George Van

>Good idea Mark, I am going to drill a hole in my Vari-Grind for a pin this morning!