Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Cachunk cachunk

Posts

Re: Cachunk cachunk

#26

Re: Cachunk cachunk

Rick Allen

>What a beautiful hunk of wood.

You need to get past 200 rpm. If you can get that thing spinning closer to 400 rpm it will reduce very fast.

I have balanced blanks on coke bottles to find the balance point of a hunk like that. If you can find the balance point on each end you should be able to increase the speed.

Longer wings on that tool will help also.

Cutting towards the center instead of along the length sometimes helps.

Good Luck

Re: Cachunk cachunk

#27

Ellis Walentine

I'll give it a try. Thanks!

Ellis Walentine

>

Re: Cachunk cachunk

#28

Re: Hand Held Bandsaw

Ron in Drums PA

>The nice thing about this tool is, while it is mounted on the lathe, you can whittle away to your heart's content. (power off of course)

Re: Cachunk cachunk

#29

How about a chain saw?

Jorge Castaneda

>Ellis, spin that thing slow and wit a deft touch your chain saw will do short work of it.

Just in case don full panoply.

Jorge

Re: Cachunk cachunk

#30

Ellis Walentine

Re: How about a chain saw?

Ellis Walentine

>I don't have an electric chainsaw, and I don't think I'll be firing up my Homelite in the shop. (The Husky is in for repairs.) One of the main reasons I didn't chainsaw it to shape in the first place is that I can barely lift this sucker. It would be nice if I could chainsaw it while it is on the lathe. Maybe this is my excuse to buy an electric saw.

Thanks Jorge.

Ellis

PS, I take it you run the piece backward... or at least saw it from the other side of the lathe.

Re: Cachunk cachunk

#31

Re: My big gouge...

John Lucas

>I agree. I don't take a big cut. The size of the gouge is more to limit vibration and fatique for me. I use a 3/8s most often for this but sometimes when trying to get rid of one or two protrusions it's easy to take too big a bite and the extra heft of the bigger gouge helps me keep it under control.

Re: Cachunk cachunk

#32

Re: I'll give it a try. Thanks!

Mike Nelson

>Uh...I'll give it a try.. ;)

Re: Cachunk cachunk

#33

Re: Cachunk cachunk

Stuart Johnson

>Use a bow saw, pruning saw to cut the high nubs or possibly a sawsall. The hand saws might not be a big a chore as one might think.

Re: Cachunk cachunk

#34

Re: Cachunk cachunk

robo hippy

>Well, for me, I would use the chainsaw to whittle it into basic shape, and then my Laguna to get it to better shape before turning. If you stand it onto the tailstock end, and scribe a circle around the center point, you can shave the edges with a good sharp ax (with an ax, you would want it sitting on the big end for proper grain orientation), a circular saw, or even a recptricating saw. Other than that, if you are going to turn it off, I would start at the tailstock end, and work my way towards the headstock. I find it easiest on convoluted pieces like yours to get a flat/smooth spot first, and then work my way down with arcing cuts, going from smooth to the rough. Are you planning on keeping any of the rough stuff in the final shape?

robo hippy

Re: Cachunk cachunk

#35

Re: Cachunk cachunk

Ed Karch

>Hi Boss,

I use a beard pattern Swedish carving axe. Choke up on the handle for good control and carve away.

Re: Cachunk cachunk

#36

Re: Cachunk cachunk

Bob Fawcett

>How about a sawzall with a long blade?

Must admit I never tried it for something like this.

I vote for the hatchet or chainsaw, but no one suggested the above (maybe for good reason).

Re: Cachunk cachunk

#37

Re: My big gouge...

bob davis

>do not use a gouge.. iuse one of thse oland type boring bars..5/8 steel with 1/4 hhs bit very large heavy handle until it is round..not much chunk..after it is round, then tne gouge..one can make one easily..larger version of ellsworth hollowing tool.

Re: Cachunk cachunk

#38

Re: I'd have considered that...

albertabob

>You might want to sleep on that thought Ellis.

Regards

Bob

Re: Cachunk cachunk

#39

Re: I'll give it a try. Thanks!

Hooligan

>Its easier, and safer, than anything else! Good luck with it.

Re: Cachunk cachunk

#40

I would use a power plane.

david

>

Re: Cachunk cachunk

#41

DANGER Will Rogers! *LINK*

Jorge Castaneda

>I mean Ellis,

All parts of TAXUS BACCATA, commonly called tejo are toxic, some parts more than others different parts of the tree contain various alcaloids, peek in here, it is in spanish but you will get the gist of it. The most toxic parts are the leaves, branches and seeds. So a lot of precaucions must be taken, but it turns very nicely.

Tejo trivia, the wood of the tejos of north west Spain were the prefered wood to make bows (arcos).

mis dos centavos

Jorge


TEJO

Re: Cachunk cachunk

#42

Re: DANGER Will Rogers!

Jorge Castaneda

>The link does not seem to work, this is the URL:

http://www.botanical-online.com/alcaloidestejo.htm

Re: Cachunk cachunk

#43

Steven Antonucci

Will Robinson = "Lost in Space"- Rogers=cowboy :-)

steve antonucci

>

Re: Cachunk cachunk

#44

Oops! : )

Jorge Castaneda

>

Re: Cachunk cachunk

#45

Ellis Walentine

Yes to the natural edge

Ellis Walentine

>I have already reversed the piece in the lathe, with a faceplate at the narrow end. If I am able, I would like to keep the top flared edge natural, without the bark, of course. The middle of the vase will be smooth, but with sapwood and/or holes where the trunk is deeply fissured.

I also have to think about how big to make the foot so the thing won't tip over. I've always been averse to this sort of stovepipe design, where the foot looks like it's welded to the surface it sits on, but I don't know a way around it for this vase, unless I make it larger in the middle and round it under at the foot.

Ellis


img

Re: Cachunk cachunk

#46

Re: Yes to the natural edge

Wayne Allen - Carson City. Nevada

>Ellis -- The shape that you have in the drawing would be a beautiful shape for this piece of wood. To keep this shape for this piece, I would leave a couple of inches of solid wood between the end of the lowest fissure and the bottom of the vase. Then I would hollow out the bottom and fill it with an appropriate amount of lead and the plug it with a piece of the same wood. (Rudi Osolnick candlestick method?) Tire weights heated with a simple MAPP torch and dripped into the hole work great. Absoultly and definitely post a picture when it's in progress and when it's finished. --Wayne

Re: Cachunk cachunk

#47

ebd

Re: German Spindle gouge? *LINK*

ebd

>Take a look at this Cutting Edge gouge (bottom of page)301-HS42H Forged Gouge 1-1/4" $65.99

The one you link to is not nearly as heavy. This one is forged from 3/8ths stock. I've been using one for years now and it is one of my go to tools. I use it for everything from roughing through internal cuts on bowls. My daughter's just learning to turn and it's her favorite tool. I'm buying myself another and getting her one for Christmas.


http://www.cuttingedgetools.com/Onlinecat.htm/WebCatalog/Spindle%20Gouge.html