Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Resaw fence for logs

Posts

Resaw fence for logs

#1

Resaw fence for logs

Jim K in Trappe PA

>I started turning a few months ago and have learned that wood is free, especially if you have a chain saw and a bandsaw (I do). I also learned that you better be realllllly careful sawing logs on a bandsaw.

Well I needed to cut a cherry log that I picked up, and decided to put together a quick resaw fence. I got the idea that if I used a 24 inch pipe clamp somehow, at least I could grip the log very tight without putting lag bolts in it. Here's what I came up with. In reality, it is not a fence, but a stability guide, as I ran it through by eye. Worked pretty well.


img

Re: Resaw fence for logs

#2

Re: Resaw fence for logs

joaz hill

>Looks like a great idea! What are the white holders attached to the plywood??

I suppose you could attach an extension to the saw table to make it more stable and less chance of rolling off the table. If you did that you could make the base of the jig wider.

This is great .. a lot safer then some of my past (dangerous) attempts in past.


img

Re: Resaw fence for logs

#3

They are aluminum brackets

Jim K in Trappe PA

>that are sold by Pony, the manufacturer of the pipe clamps. I think I bought them in Woodcraft or maybe even Sears about five years ago.

Re: Resaw fence for logs

#4

One more thing...

Jim K in Trappe PA

>It is more stable than it looks. The log is the center of gravity, so the small footprint of the fence-base is not holding the log, it is acting more as an outrigger.

I feed the log through the blade by pushing the log with one hand, and have the other hand on the fence keeping it firmly sliding along the table. Once it gets 98% through, I move the log-hand to support the piece that I cut off.

Re: Resaw fence for logs

#5

Re: Resaw fence for logs

EagleS.C.

>I do essentially the same thing with a sled for my BS and a short Bessy clamp.

The foot of the clamp rides on the fence of the sled.

Best part is the plastic jaws won't harm the blade.

It is an odd ball clamp no match.

I bought it to use as a "holder" when I was making some arched top doors for some cabinets on a router table and starting pin.

If it gets screwed up,it's only a Bessy.

I have plenty of Cabinet masters.

Re: Resaw fence for logs

#6

Re: Resaw fence for logs

MP Wall

>I think its a great solution to the problem of bandsawing round logs and that you should send it in to the AAW and Woodturning magazines.

MP Wall

Re: Resaw fence for logs

#7

Thanks, good idea! I will.

Jim K in Trappe PA

>

Re: Resaw fence for logs

#8

Article in Fine Woodworking...

David

>had a set up with similar features, and I built one a while ago. Was also briefly mentioned in their 25th Anniversary Issue that featured some of the great tips and jigs that have been shown in the magazine. It utilized the slot that is on most of the band saw platforms these days. This really helps to keep the cut straight. The band saw I use is very old, and I had to make some other arrangement for keeping the log in line as the platform, clamp and log is pushed through the blade. Great minds think alike, I guess.

Re: Resaw fence for logs

#9

From FWW

Dominic Greco at home in Richboro, PA

>

Your version reminds me of a cross between the one featured in American Woodworker (August 2000, Issue #81) and that shown in Fine Wood Working's 25th Anniversary Issue (Winter 2000/2001, issue #145)

I made FWW's version back a couple of years ago. It worked OK and was used several times. But I found that it's design didn't allow enough for blade drift. It was also a pain hefting those logs up to the height of the bandsaw table!

Then I found that I could do just about the same operation by splitting the log down the middle with a chainsaw and using a "industrial strength" resaw fence.

See ya around,

Dominic


img

Re: Resaw fence for logs

#10

Thanks for the references.

Jim K in Trappe PA

>I'll take a look.

Jim