Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A break from the steel discussions...

Posts

A break from the steel discussions...

#1

A break from the steel discussions...

John in NM

Here's what I finished up this weekend. Pics are so-so, I left my camera at work so these were taken with an ancient flip phone.

Stock is for a copy of a Winchester model 92 that came with a really crappy stock. I had the end of a black walnut board that looked a bit like French walnut, so I saved it for this project.




I finished sanding last night and dipped it in linseed oil, followed by Bill's burnt umber stain - in this case I just rubbed a little of the artist's oil paint into the still wet linseed.

Re: A break from the steel discussions...

#2

Nice!

Bill Houghton, Sebastopol, CA

How do you lay out the work? And are those stocks symmetrical, or do you have to know if your customer is shooting right- or left-handed, and adjust as needed?

Re: A break from the steel discussions...

#3

Re: A break from the steel discussions...

David Weaver

Nice..are you making a matching foreend?

Re: A break from the steel discussions...

#4

Fascinating, John

Joe shelton

And beautifully done, too.

How intricate is the inletting at the receiver?

Do you get to test fire it after the installation?

Thanks for posting this.

Joe

Re: A break from the steel discussions...

#5

Thanks!

John in NM

This is for one of mine, so I do get to test fire it... repeatedly :D

Inletting isn't too bad really. Tricky part about it is that there's an upper and lower tang so there is a lot of test fitting to get a good fit between them without being too loose.

Re: A break from the steel discussions...

#6

Yes....

John in NM

But that is a bit further out. Not sure yet what to do about the channel for the magazine tube - its a funny size so going to be hard to find a bit that will cut it.... I could drill it, but its pretty hard to drill something like that straight - at least for me it is :D

Re: A break from the steel discussions...

#7

Re: Nice!

John in NM

This one is symmetrical, so left vs. right hand won't matter.

Layout isn't too bad, you just need a couple reference surfaces, like building furniture or pretty much everything else. You cut the inletting first and make sure the metal fits, then scribe to the metal and sneak up on the scribe lines.

Shaping is the fun part though, that and finishing.

Re: A break from the steel discussions...

#8

Scrumptious block of walnut!

Wiley Horne

John,

Thanks for posting! Did you pattern that stock to the original Winchester, or is it customized to a pattern you prefer?

Wiley

Re: A break from the steel discussions...

#9

Looks like the original!


Re: A break from the steel discussions...

#10

Re: Scrumptious block of walnut!

John in NM

Its patterned after the one that came off it, more or less. These copies were made in Brazil, and the stock shape is pretty good, but the comb is a lot higher than the original Winchester pattern. I cut it down a bit, but I probably could have done more cutting without harming the looks any. I just hate cutting off more nice wood!

Re: A break from the steel discussions...

#11

Re: A break from the steel discussions...

Bruce, a MN Galoot

Very nice work, John! The hand work makes that a challenging job. There’s a guy who works out at the gym we go to who refurbishes guns and builds stocks from scratch, hand checkered, too. He uses English and Turkish walnut blanks that can run more than $1K.

Re: A break from the steel discussions...

#12

Re: A break from the steel discussions...

John in NM

None I've ever made can support that kind of wood price! Nothing like a stock blank to make wood pricey :D I think I've paid maybe $200 for a blank, but for a full size one I can usually get 2 sets of the ones I sell.... Though I have paid a lot for maple burl slabs, but I can usually get 3-4 sets out of those.

Its a lot of fun though :D

Do you still want a Sandvik chisel? That was years ago, but I finally duplicated most of my sizes, so I could spare you one. What size would be good?

Re: A break from the steel discussions...

#13

Very nice job.


Re: A break from the steel discussions...

#14

Re: Yes....

david weaver

I couldn't really provide much helpful talk without having something to copy in hand. I'd bet the neatness of the work inside the forearms probably varies a lot by era and manufacturers, but I figured you'd remake it given how lovely the stock...well, stock stock? is. It'll embarrass the fore part of the stock.

I've had pretty good luck with things like you're talking about with patternmaker's gouges and specialty scrapers (as in, if the grain lifts when you pare it, you can just square up the front of a gouge and scrape it instead. It's slow work combined with some decent double cut files, but it's safe).

Re: A break from the steel discussions...

#15

Re: A break from the steel discussions...

Frank D. in Montreal

Very nice job! You may have said this, but how do you do the chequering? Can'T wait to see it mounted with a finish.

Re: A break from the steel discussions...

#16

Re: Yes....

John in NM

I have a piece for the forend from the same board. It doesn't have the nice stump figure as I recall, but it is still a pretty piece of wood.

Here is the basic shape to make:


That round longitudinal cut at the bottom is the tricky bit. I typically do these with a milling machine and a ball cutter, but this one is a weird size, between 5/8 and 3/4, for which there is no readily available bit. Probably I will either use an oversize one or delete the overhanging part and just use a ball nose cutter and then scrape to fit by hand.

The rest of the forend is easy. Beyond that round channel, the hardest part of making one is getting the length right.

Re: A break from the steel discussions...

#17

checkering

John in NM

When I do it (rarely) I use my dad's old set of Dem-bart cutters. They are basically just handles with tiny sections of a file that can be swapped on the handle. Some are single V and some are 2x or 3x V's at various line per inch spacings. I have a few that have 2x V's but one is smooth and the other cuts, for working in a line without overcutting the line before that is the reference.

There was a company that made power checkering heads in Deming NM, not too far from where I live, but they went out of business maybe 10 years ago. It was undoubtably a sole proprietor who either retired or passed away, as the market is very small these days. They turn up on ebay often enough, but I don't do enough checkered work to justify the cost (usually $1k or so). Checkering by hand is more fun I think, but then I don't have to make $20 an hour doing it - probably $.50/hour the way I do it!

More often I stipple finish textured grips. I make one in particular where that is the traditional look. Its what you see on Anschutz target rifles if the term doesn't bring up a picture for you. I never could find acceptable tooling for that, so I made my own (and the first was a hand tool too :D )

Re: A break from the steel discussions...

#18

Thanks Brian


Re: A break from the steel discussions...

#19

Re: not hand tool friendly!!

david weaver

That design doesn't look hand tool friendly!!

Not sure how they make it at the factory (tube size notwithstanding), but I can't imagine how one would make that by hand without oversizing it for stability and final sizing it down.

Re: A break from the steel discussions...

#20

Sure isn't...

John in NM

I doubt those were ever made by hand. I've drilled holes like that before, so you could do it with a brace if you used a really big chunk of wood and then cut the barrel channel to match.

In a factory, a lot of those long cuts are made with something similar to a horizontal mill - that is how I would do the barrel channel on that piece for example, gang together about 6 cutters with spacers on a long arbor and do 6x at once. But that round hole has to be done with something like a router or perhaps they did drill it. I'll look closely at one when I get back to the shop (likely a couple weeks) and see what I can tell from tool marks.

Re: A break from the steel discussions...

#21

Re: watching someone at gibson do necks

david weaver

Reminds me of watching people in the gibson factory work. Making a guitar neck isn't difficult, but it takes some time. Maybe an hour to get the contour right end to end and scrape the neck so you can pick it up later and make sure all of the curves are faired properly.

But, then you watch the gibson factory (before they went to CNC) and there's some dude or dudette with roughed out blanks and they contour the neck on the end of a belt grinder with coarse sandpaper. It's an operation that would take at least several dozen necks to get an acceptable result with but, they're doing one after the other quickly and the result is really nice.

I'd bet there's some fixture that drills those foreends horizontally and then a bunch of other fixtures that it fits on after that (drill rather than mill only because it's cheaper).

I would puzzle over making something like that, but in the end would drill the hole by hand with a visual guide in an oversize billet and then size it square, mark the ends and cut the waste out nearly to size with a rip saw while it was still square and then profile the outside. It would take a LONG time, and you have to have a good day to do it all right. It could take an afternoon, and it would still be something needing a rest so that you could look at it with fresh eyes the next day.

I'm sure the factory has a process that doesn't require the operator to have a good day. I'd love to see it. I'll bet it was somewhat low tech (but efficient) until recently.

Not having a bit size to do it is pretty hard to work around, though, and it may take two or three tries not to overcut a line.

Re: A break from the steel discussions...

#22

Homebrew horizontal drill maybe?

Wiley Horne

Hi John and all,

Just out of curiosity, I dropped a Milwaukee 1/2” ‘Holeshooter’ drill into my LV twin-screw vise:

https://www.flickr.com/photos/78661951@N07/48082841568/in/album-72157708940252281/

Amazingly, the drill has parallel surfaces on handle and body (it doesn’t look like it). It dropped it perfectly solid. A blank could be jigged to run straight into the drill. Could make a heading from each end if blank square and true.

Just a thought. John’s rifle got me looking up Sako, though they’re very different.

Wiley

Re: A break from the steel discussions...

#23

I've done something like that...

John in NM

But with a lathe and the tool rest to steady the work. Not sure that your set up wouldn't work vastly better :D

I've seen lathe setups with a power head on each side of the work, aligned to one another, and a moving carriage in between to push the work into each bit. That way you could drill two holes and have them come close to lining up without a big setup headache - but you had the headache of dedicated machines sitting around :D

Re: A break from the steel discussions...

#24

Re: I've done something like that...

Bruce, a MN Galoot

The engineer/gun restoration acquaintance of mine that I mentioned to you roughs out his stocks with a Bridgeport knee mill and a 2d CNC.

I suspect you could drill that hole with your drill press if you have a table that rotates.

Re: A break from the steel discussions...

#25

Re: I've done something like that...

John in NM

I'm thinking I will just size it up a little and use my mill with a standard ball cutter - basically how your friend does it.

The forend is secured by front and rear caps, so it really doesn't need to be a super snug fit. I could always backfill by waxing the tube and pouring 5 min epoxy into the gap if I later found it crucial to get a tight fit.