New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Leg vise accessories

Posts

Leg vise accessories

#1

Leg vise accessories

Derek Cohen (in Perth, Australia)

Three accessories for those with a leg vise ...

I posted recently about the kitchen doors I am building ... 22 in all. They are all in Hard Maple, from rough sawn timber imported from the USA. As mentioned previously as well, all Shaker style to replace doors with raised panels from the existing kitchen built 20 plus years ago.


I've now completed 12 of the doors, and am in the process of assembling the rest ...


As I was clamping yet another frame to side of the bench, I decided that I had enough of fiddling with this process, and decided to modify my leg vise to make it more friendly. The problem was that the section of the bench facing the chop was lined in leather for added grip. This lifted the work away from the side of the bench, and, when clamped in the vise, the frame would rack. I had got by through shimming the gap. Of course, if I adjusted the frame, the bloody shim dropped out, and I would have to start all over again!

The first accessory was easy enough ... a shim that would not fall off the bench ...


The shim is the same thickness as the leather ...


Next ...

One of the big advantages of a leg vise is that one can clamp a door down one side. The problem is that the vise racks. Over time the vise will damaged. More immediately, it does not hold as firmly as when the full width of the face is used. The time honoured method for dealing with this is to have a deck of wooden cards that may be dropped in the opposing end. Something like this version, which is sold by Lee Valley ...


I did not want something that would be lying around. I have enough bits and bobs lying around already. Even the shim (above) is another item to lie around, and I shall have to come up with a better idea to replace it.

Well, I came up with an idea for the vise which I have not seen before, so it may just be original (I doubt that, but it is nice to imagine). This a simple depth stop for the outside of the chop.

This was built from Jarrah scrap. I found a thread that I could mortice into the wood. The hole for the thread was drilled with a brace and bit.

It was hard going. The bit was sharp and the threads were clean and designed for hardwood. But they were not going anywhere, even with much downforce. I recalled a tip that a fellow Aussie had posted on the Australian forum (and, indeed, had won a prize from Pop Wood magazine). It involved how to use a forstner bit with a brace. To do so, he drilled a pilot hole:

https://www.youtube.com/watch?v=j_unwqESVfA&feature=youtu.be

It occurred to me that this may work with the bit as well ...


Did it ever ..!


So here is the depth stop ..






Finally, all could be used together, and attaching and holding frames became a breeze ...


The third accessory? Well, have you not wanted to use the leg vise like an end vise, that is, to clamp boards across the bench? Like this ...


Obviously, on the bench are dogs like these ...


These are from Lee Valley. I cover the faces in leather to prevent marring sides (I do the same will all hold downs).

The other side is the leg vise chop, and that, too, has a dog sunk into it ..


These are also from LV, the "prairie dogs", which are spring loaded ..


When no longer needed, they are pushed into the chop and out of the way. Pop them up again when you choose ...


Lots of fun, but all useful.

Now, how do I build the shim into the bench?

Regards from Perth

Derek

Re: Leg vise accessories

#2

This interesting post.....

Bill Tindall, E.Tn.

........made me appreciate my Record steel vice :)

For example, to plane the edge of a frame like you have I slip it over the vice, activate the quick release to snug the frame , and turn the handle to secure it. It already has a dog for bench top clamping and clamping something long along the bench length is readily accomplished with a wooden screw clamp on the end opposite the vice which is secured to the bench with another clamp.

Re: Leg vise accessories

#3

Re: This interesting post.....

Derek Cohen (in Perth, Australia)

Hi Bill

When I built my current bench about 5 years ago, I decided on a leg vise as I viewed it to be ideal for edge jointing - quick to set up and with greater holding depth than the Record 52 1/2 I had on my previous bench. I have been very satisfied with the leg vise so far, but clearly there are pros and cons in every deal, and you will find some things a Record will do better, and vice versa.

The depth stop on the leg vise works very well to prevent racking when clamping on an edge. My old Record suffered from the same racking problem. In fact, I had to get rid of one about 10 years ago as it racked so much.

Regards from Perth

Derek

Re: Leg vise accessories

#4

Re: Leg vise accessories

roger lance

Derek.....enjoyed your post.....and appreciated your observation about there being trade offs between competing products (vises) which is what I was referencing below regarding competing spokeshaves when I spoke about tennis racquets.

Like Bill, I'm using a Record and find that I only need "leather" on the chop to eliminate stock slippage/movement. Do you really need the additional leather on the bench face? If not, you'll have solved your shim issue.

Re: Leg vise accessories

#5

Re: Leg vise accessories

don stephan

Always a pleasure following another from Down Under (Richard Raffan is my favorite for turning instruction). Could you start incorporating some "Down Under" talk - expressions - to keep us on our toes?

Re: Leg vise accessories

#6

Nothing to do with Leg vise accessories

Derek Cohen (in Perth, Australia)

Could you start incorporating some "Down Under" talk - expressions - to keep us on our toes?

Grief Don, I make every effort to keep my phraseology clean! :)

There's a fun website to browse here: https://thingsaussieslike.wordpress.com/2011/09/16/no-2-vegemite/

Go for your life ...

... and goodonya

Derek

Re: Leg vise accessories

#7

Re: Leg vise accessories

TomD

Nice. Are those angles part of a mock-up or are you actually planing to share shop space with them. I couldn't do that to my bench, and they don't look all that strong. I do have a bag of them and used them to extend a bench for a metal lathe, worked great, but the whole bench was at a more pragmatic level, and not permanent, though parts of it are still there. :)

Re: Leg vise accessories

#8

Re: Leg vise accessories

Derek Cohen (in Perth, Australia)

Hi Tom

The steel angles are very strong. They are also invisible when viewed from the front or side of the bench.

Plus, it is not as though my bench lacks for metal. This is hinted at from the front ...


.. and then underneath you can see a chain system driving the parallel guide ..


If I find a better system that the vise depth stop, I will unscrew the steel angles and plug up the 4 small holes.

So far so good. :)

Regards from Perth

Derek

Re: Leg vise accessories

#9

Re: Leg vise accessories

Derek Cohen (in Perth, Australia)

Roger, the leather has helped prevent slipping.

I have temporarily glued on more leather along the side of the bench. However, I think that the fix will be to strip away all the leather and plane the side with a toothing blade to rough up the surface. When I built the bench (4 years ago now), it was finished with danish oil to waterproof it. This left a slightly slippery surface. I recognise now that the bench sides were not a good partner for the vise chop.

Regards from Perth

Derek

p.s. I liked the tennis analogy.

Re: Leg vise accessories

#10

The search for the magic stick......

roger lance

There is something in our culture....our psyche.....our mythology that says there are objects that possess mystical, magical powers that will grant its owner great power, adulation, success, etc etc. Everything from Excaliber to Robert Redford's bat in the Natural to Steve McQueen's car in Bullitt to Clint Eastwood's 44 magnum (the most powerful handgun in the world and will blow your head clean off) on and on. And, we go for it.....we buy into it.....marketeers have a field day playing us with this deception.

Back to wood tennis racquets for a moment.....remembering Rod Laver and his unusually well developed forearm......it was postulated that metal racquet frames allowed weaker players to hit a little harder without going through the efforts to develop as Laver had.....the tennis racquet market turned on that premise.....wood racquets lost marketability and metal took over.

I believe that there is some of this dynamic in woodworking/tools as well. There are clearly tools that are better than other tools.....but, sometimes the differences in things may only be marginal at best and without magical qualities.

Re: Leg vise accessories

#11

Re: The search for the magic stick......

kim

I used and loved wooden racquets for the first 40 years I played; but 10 or so years ago I bought a Head metal racquet. It is a wonder, has all the behavior I'd been waiting for, enhanced my control, speed, and power. So....there you go. :)

Kim

Re: Leg vise accessories

#12

Re: The search for the magic stick......

kim

Almost forgot, my tennis elbow disappeared with metal.

Re: Leg vise accessories

#13

Re: This interesting post.....

Warren in Lancaster, PA

I use a slanted leg vise, which is a Pennsylvania Dutch design. Large dogwood screw. Much easier than a quick release.

Re: Leg vise accessories

#15

Re: The search for the magic stick......

Derek Cohen (in Perth, Australia)

Roger, it is all about feedback and connection.

I was a very serious tennis player in my youth. I often wondered where I'd be today if I had been playing after the pro years started. Unfortunately, I was already at university by then and had switched to squash as it was more convenient.

In both tennis and squash there were very noticeable differences in racquets (I used Dunlop Maxply. Not all were the same). I much preferred lighter heads since they responded to ground strokes and aided touch. Getting string tension right was yet another level. Power came from timing, not mass (which is the modern trend).

Rod Laver, Roy Emerson, and Ken Rosewall were my heros.

I had not thought about this area in years. Now I realise that there is a possible connection with my interest in hand tools ergonomics - why I am so interested in their feedback and balance .. touch.

Some of the racquets I experienced were heavy and dead. Some handtools (e.g. chisels) today feel the same way.

Does this make sense?

Regards from Perth

Derek

Re: Leg vise accessories

#16

Re: Slanted vs Vertical

Warren in Lancaster, PA

With a slanted leg vise a board may be held in the vise vertically without racking.

Re: Leg vise accessories

#18

Re: The search for the magic stick......

roger lance

Derek.....it makes sense to me.....finding the right racquet definitely involved feel, feedback, and ergonomics.....just like you've been talking about with hand tools.

When I began to get interested in tennis, Australians ruled.....then, Chuck McKinley began to come on.....and Stan Smith.....

Those were great days.....but over 40 years ago.....

Its good to know that we shared this interest.....tennis, in those days, was more than just a sport.....it was a code of conduct.....being respectful.....it was a good way to grow up.

Re: Leg vise accessories

#19

Now, that's certainly magical.....

roger lance

if a metal racquet could restore my hair......I'd get one.

Re: Leg vise accessories

#20

Re: Leg vise accessories

William Duffield

I don't see a picture of the business side of the leg vise jaw. Did you install a metal plate in it so the shim stop doesn't over time gouge the surface of the jaw?

Or is that jarra harder than brass? :D

Re: Leg vise accessories

#21

Re: Now, that's certainly magical.....

kim

Well, it's not just any metal racquet, it's a Head. I'd tried a Wilson metal some years before, but "all" it did was get rid of tennis elbow.

Kim

Re: Leg vise accessories

#22

You folks are undermining .....

Bill Tindall, E.Tn.

.....that well known proverb that it's the workman, not the tools. I fear you will be encouraging people to spring for that $XXX set of chisels and saw that "will" improve their dovetails.

BTW, is anyone doing woodworking? I spent the day fretting over selecting the perfect pieces of quartered ash for a cabinet and accomplished little else.

Re: Leg vise accessories

#23

Woodworking? Definitely.

Derek Cohen (in Perth, Australia)

Bill, I have completed 16 Shaker doors for the kitchen. After resawing and turning the 2" thick rough sawn Hard Maple boards into rails and stiles, there is the careful book matching for all the panels.

I think a furniture maker building kitchen doors must approach this differently from a kitchen specialist. We take so much more time in the task, while a kitchen specialist seems to zip along. How do they do it?

Regards from Perth

Derek

Re: Leg vise accessories

#24

Re: Leg vise accessories

Derek Cohen (in Perth, Australia)

I don't see a picture of the business side of the leg vise jaw. Did you install a metal plate in it so the shim stop doesn't over time gouge the surface of the jaw?

Or is that jarra harder than brass? :D

Hi William

I have not yet installed a metal plate to receive the bolt head. While some Jarrah is indeed as hard as some brass, the chop is holding up . I am deliberately letting it score the wood - slightly so far - before using the mark to insert an Australian cent on the spot - they went out of circulation some years ago. (Translation: I am too lazy/preoccupied with more important items to get to this at this stage :) ).

Regards from Perth

Derek

Re: Leg vise accessories

#25

Re: Woodworking? Definitely.

kim

They buy preassembled cabinets made of various inferior materials. Don't last too long.

Kim