New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

How to re-handle a peavy question

Posts

How to re-handle a peavy question

#1

How to re-handle a peavy question

Bill Tindall, E.Tn.



This was the first inexpensive log roller I have seen at a local flea market. I did have to remove a broken handle, accomplished by putting the point in the camp fire. I will mount the billet to be turned into a handle vertical at the drill press and drill the pilot hole for the point.

The question is how to drive in the point without damaging its end?

Re: How to re-handle a peavy question

#2

Re: How to re-handle a peavy question

John in NM

Make a couple blocks with 45 degree blind cuts so that when clamped together you have a square hole smaller than the shaft of the point. Screw the blocks together so you can pound on them rather than the point.

Re: How to re-handle a peavy question

#3

Re: Or the right way might be like a hammer

TomD

When you want to put a hammer head on, you don't hit the hammer head, you press the head on, then you invert and whack really hard on the opposite end, on the shaft. The inertia of the head is such that you pound the handle through it. It confuses people because they feel that with the head hanging off the end of the handle, and hammering it in the direction of the ground, it ought to fall to the ground but it is set on the handle instead.

The same would work here, you insert the metal pike, then pound with a really large hammer on the end of the handle. if you have the correct clearance for the parts the pike will be set into the handle. Thinking 4 pound sledge in one hand, whack on the dangling handle with held in the other hand.

Or you can just shove the pike into some really hard end grain, and hammer away.

Re: How to re-handle a peavy question

#4

The physics is not favorable

Bill Tindall, E.Tn.

In the case of a hammer (or ax or splitting maul, ) the head is heavy and the handle is not. When the handle is whacked it accelerates into the head. The head, because it is heavy, is slower to accelerate and doesn't catch up with the handle instantly. The result is that for an instant the handle is moving faster than the head. As a result it gets driven into the head.

For the mathematically inclined F=mA (force equals mass times acceleration). Rearranging, A = F/m. Force is the whack. Bigger m, less A. The result is the heavy hammer head doesn't accelerate as fast upon whacking and appears nearly stationary as the handle is driven into it.

In my case the spike weighs but a tiny fraction of the handle. The force pushing the spike into the handle will not be zero, but it will be vastly less than the hammer situation. Never-the-less, I'll give it a try.

Re: How to re-handle a peavy question

#5

Jack Guzman from Maine

Re: How to re-handle a peavy question

Jack Guzman from Maine

I watched a youtube video on making a homemade peavey . In it the guy simply twisted it into the predrilled hole with a wrench on the square sides of the point. There wasn't alot of detail. I searched for "homemade log peavey"to find the video.I don't imagine it needs to be overly snug,that point doesn't receive alot of stress in use.---Jack

Re: How to re-handle a peavy question

#6

If you really want the last word... *LINK*

John in NM

You could ask these guys :D

They were across the river where I used to live in Maine.


Bangor Peavey

Re: How to re-handle a peavy question

#7

Re: The physics is not favorable

William Duffield, on the Cohansey

Drop the end of the handle on a rock or anvil, repeatedly. The handle and head stop more quickly than the spike, so it's driven in. You might want to cut the handle a little long, and after you've driven the spike in, cut off the damaged end of the handle.

Alternately (or before using the above strategy) you could clamp the spike in a vise, heat it with a torch, and burn it in.

Re: How to re-handle a peavy question

#8

Such a deal

Bill Tindall, E.Tn.

I could buy one from these guys for $85.

I spent 2 hours at the flea market finding a broken one. 1 hr struggling to remove broken handle. 1 hour to make camp fire to burn it out (credit 1/2 hr for the steak cooked on camp fire). Half hour rummaging to find a handle blank. 4 bd ft of 12/4 oak $20. 1.5 hour to turn handle. 0.5 hr to derust the metal and paint it (estimated, not painted yet). Well that's more than minimum wage, OK for retirement.


Re: How to re-handle a peavy question

#9

Re: Such a deal

John in NM

Don't forget shipping costs - about $30 I'd bet :D

Re: How to re-handle a peavy question

#10

Wow

Bill Houghton, Sebastopol, CA

I didn't realize that the peavey was that recent a design, nor that the company that first produced it still is. Amazingly nifty.

Re: How to re-handle a peavy question

#11

Re: Such a deal

Larry Barrett

They sell axe handles, too. Are you still looking for one?

Re: How to re-handle a peavy question

#12

Re: The physics is not favorable

TomD

I will be interested to hear how it works out, even if there are better ways ultimately. I have two such project, one almost identical to yours, and the other the tool without a pike.

My thought is that the relative weight of the head and the handle are not that relevant. What counts is that the spike has considerable weight, so it should seat into the hole so long as the hole is correctly shaped, which might be a trick. The fact that the handle is heavy doesn't mater, it is like an immovable object meeting an irresistible force, which isn't so great, except in this case there is a hole.

Practically I wonder if I could hold a peavy and hit it hard enough, but if I could, it should work. Sorta like it doesn't make that much difference if a person or an arrow are moving at 200 ft/sec at the moment of impact, it is still going to hurt.

Re: How to re-handle a peavy question

#13

Re: The physics is not favorable

TomD

I'm pretty lucky, but some things just don't work for me. I can't travel down the hwy with a canoe loosely tied on my roof, flapping around, I have to have everything perfect, and even so there is a chance of taking out a schoolbus load of childred. Likewise, that whole thing about burning something into a hole, always looks good when other people do it, but for me, I think i would just end up with a critically weakened handle. Though this would be the one to try since the ferules are normally pretty massive.

Re: How to re-handle a peavy question

#14

burning experience, you are right on

Bill Tindall, E.Tn.

I tried this burning thing with a medium sized lathe skew that had considerable heat capacity. Heated with propane torch with blade in the vice. Drove on the handle. It began to smoke, then a puff of smoke and a ball of flame shot out of the handle, filling the shop with smoke.

With the huge heat capacity of this spike, the opportunity for a repeat performance is favorable. Clearly, burning on a handle is a delicate balance of just enough heat. I don't intend to ever try it again. Better to drill a hole the diameter of the tang thickness, drive on the handle and fill gaps with filler strips epoxied in.

Re: How to re-handle a peavy question

#15

The easier way...

John in NM

Is to protect the point of the spike and drop it point down on the ground. The mass of the handle and hook are much greater than the point, so they will not decelerate as rapidly as the point will when dropped on a hard surface. Same concept as the one you related earlier, the thing is that you always have to set it up to decelerate the low mass part first, causing the higher mass part to drive the parts together.

Re: How to re-handle a peavy question

#16

Re: If you really want the last word...

William Duffield

I have a timberjack made by those guys.

Re: How to re-handle a peavy question

#17

Re: burning experience, you are right on

William Duffield

I've only handled files with the burn-in method. They have a much smaller tang. I had lots of smoke but no fire.


Re: How to re-handle a peavy question

#18

Re: Epoxy and Filler Strips

William Duffield

Instead of filler strips to fill the gaps between the tang and the handle hole, why not just add colloidal silica to the epoxy mix, pour it into the hole and then drive the spike in? I think the silica filler should be as strong as, or even stronger than wood strips, and definitely easier to "fabricate."

Re: How to re-handle a peavy question

#19

Re: How to re-handle a peavy question

Bob Hackett

It has been my experience that you can drill the handle to be a light press fit for the spike and then drop the head onto the handle and align it as you see fit. You then drive the spike into it`s socket using a hardwood block so as not to damage the spike. (I`ve also seen a brass mallet or drift used to drive the spike in but that is not kind to the brass). Once you drive the spike in place it will tighten up the head somewhat. Final driving of the handle onto the head will also tighten the grip on the spike.

PS- The spike will either be soft steel or wrought iron, either way a file will easily dress out any damage caused to the tip either during assembly or during use.

Re: How to re-handle a peavy question

#20

Re: Wow

Kevin French

We were at the spot yesterday were Joe got his got his idea for the Peavy. He was on the bank near the 'Cribworks' on the West Branch of the Penobscot River in Maine. He saw the men in the water using 'Swing Dingles', went home made the Peavey in his shop, brought it back, everyone loved it, he made many more, BUT never patented it.

Re: How to re-handle a peavy question

#21

What is the spike used for?

Bill Tindall, E.Tn.

I occasionally worked at a small unmechanized mill and logs were rolled with an assortment of peaveys or cant hooks, what ever was closest. They both rolled logs equally well. The spike must have a purpose but I never discovered it.

Re: How to re-handle a peavy question

#22

craigd

Breaktime is over!


Re: How to re-handle a peavy question

#23

Re: What is the spike used for?

Bob Hackett

It is my understanding that the peavey is a more modern evolution of the cant hook. Cant hooks were originally just a long, relatively straight rived out length of wood that was morticed and drilled thru for the hook, which is the real heart o this tool. As you might have guessed once folks began sawing out handles instead of riving them these tools needed added reinforcement so a forged or cast assembly was devised to allow mass produced handle blanks to be fitted and used with success.

This is the most plausible story I have yet to hear from the "campfire historians" I meet who still use these tools and ponder such things during the long Maine winters.

As for the spike, this supposedly was added as a way to appease the workers who moved onto dry land after spending time out of the water working with spiked tools like pikes and pickaroons. You had to use a little bait if you wanted to entice someone to pick up, buy and put to use a heavy clanking metal monstrosity that was bound to be more trouble than it was worth. :D

Re: How to re-handle a peavy question

#24

Re: How to re-handle a peavy question

Jim Pugh

Bill, presuming that the wooden shaft will have a pilot hole in it, why not drive the point in using a long pipe clamp?? Put a piece of tape on the point shaft so you know when you are home.

Re: How to re-handle a peavy question

#25

will give it a try

Bill Tindall, E.Tn.

It may be the jaws of clamp will not be long enough. The handle is 2 3/8 at fat spot, but easy to try.

I suspect that what will work is to place point on a seasoned hickory log section and bash the end of the handle. As someone pointed out the fit does not have to be so tight that excessive force should be required.