New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Update on needing help on what to order next

Posts

Re: Update on needing help on what to order next

#26

Not so weird Ron

Tony Wilkins

The only hesitation I have is that we're going to have to move this winter (if all goes well) and I'm not wanting the weight on our move. Plus it's an odd experience to unpack wood carefully wrapped in paper by Army movers.

Re: Update on needing help on what to order next

#27

Re: Tormek Question

david weaver

Here's what I've had, just offering my opinion before you dump a lot of money:

1) a ryobi grinder

2) a baldor grinder (that's the thing I actually use)

3) a viel belt grinder (I torched the ao smith fan motor that drove it)

4) a kalamazoo belt grinder (still use that, too, but not nearly as much as the baldor)

5) an 8" wet wheel grinder (gave it to a friend)

6) a tormek supergrind (gave it to a friend)

7) various coarse stones

It's my opinion that you shouldn't get a tormek this early on. There are a lot of shops that have dry grinders, but there aren't many that have dry grinders and folks don't use them. There are also a lot of shops that have tormeks, and there are a lot of tormeks that don't get used much because they aren't as convenient.

As much of an indulgence as the baldor grinder was, it is only the same price brand new as an older tormek is used. You will find a lot of people who gush about tormeks. Often, they are people who have bought them recently. That group of gushers will much less often include people who have been working wood for a long time, which should tell you something.

Re: Update on needing help on what to order next

#28

Re: Tormek Question

cstanford

Tormek.... Stu..... spells doom. What about wood? What about clamps? Turning tools? Carving tools? Hinges? Drawer pulls? Locks? Screws? Other assorted hardware? Sundry supplies? Solvents? Paints? Shellac? Varnish? Decent drawer pulls for the average chest of drawers will set you back at least $200 unless you buy cheap crap from a big box store. For God's sake don't build something entirely by hand and then hang cheap Chinese hardware (Rockler cr*p) on the thing.

This is an expensive hobby. Better get a pencil out and start adding. It takes more than tools to build and deliver something, whether to a customer or to your own living room.

Re: Update on needing help on what to order next

#29

Michael Donaldson

I've had military movers pack up

Michael Donaldson

For me before. Not only did I have carefully wrapped wood, they also carefully wrapped up a garbage can...with the garbage still in it. Are you INCONUS? because if you are, you can move some of your stuff yourself (like your wood, tools, etc.), then just make sure that what the movers take is less than your weight limit, Even if you only move one pound, you get reimbursed for the rental truck and gas, regardless of weight. I had to do that on my separation move (still in progress), and it has definitely paid off.

Re: Update on needing help on what to order next

#30

What I ended up with...

Tony Wilkins

...these:

LN #5

Couple of LN chisels to see if I like

Router Plane

LV Small Plow

LV Medium Shoulder Plane

David Charlesworth Chisel technique DVD

I'm going to get a coarse water stone (thinking Gokumyo-Ryu 300) and a flattening stone when I hear back from Stu.

Re: Update on needing help on what to order next

#31

Milestone completed!

Wiley Horne--So. Calif.

You did well. Have you picked the wood yet?

Wiley

Re: Update on needing help on what to order next

#32

Walnut

Tony Wilkins

I have some nice 8/4 walnut that I've sawn the legs out of and will probably resaw for the top to book match it together. I already had some 4/4 that I've got the 'sides' ready to go out of. That should give me all I need for the shaker table plus some left over. I've got a board of cherry 4/4 that I haven't decided what to do with yet.

I'll probably order some 8/4 hard maple to do the moxon vise out of (per the plans from Benchcrafted).

Depending on how it goes with the shaker table I might make another one. I'm trying to stay in the 'hand tool friendly' domestic woods - walnut, cherry - but I might get some mahogany to play with.

From there I'm going to go through the projects in Tom Fidgen's book. I had started with the intent to do the shop tool projects out of Jim Tolpin's book but the wood I got turned out not to be straight grained enough. I figure with the wood I'm getting for these other projects that I should end up with some good material to fit in those projects (straight edge, squares, etc).