New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

January- what are you working on?

Posts

Re: January- what are you working on?

#26

craigd

Re: Joint Stool

craigd

Thanks! Yes, rived. Neighbors down the street cut down a big oak and I snagged 2800# of it.

You are correct, I used the Alexander/Follansbee Make a Joint Stool from a Tree book as a guide.

Re: January- what are you working on?

#27

Re: Your new tapering jig...

William Duffield

Steve's jig is almost perfect, and a vast improvement over any I've seen or used before. This is described in Fine Woodworking Number 229, December 2012. Here's a photo of the man himself actually tapering a leg with his jig. If you want to build and use one, starting with the FWW article is essential.


My improvements are very minor.


I used an improved handle. I made a whole batch of these, and also use them on table saw push sticks, and the "boat" for my jointer. I have a few more laying around for future uses. The hang hole is not functional for this application. They're made from 1" thick tulip poplar. I attach them with 10 mm. Festool Dominos. I didn't like the first location I tried, but moving it over an inch or so was trivial.


I'm going to want to taper some pieces narrower and shorter than the typical table leg, so I made the end block moveable. It is held in place with Dominoes, so this is easily done. Note the warning marks on the end block. I find it very easy to forget that there is a screw sticking out the end I can't see. Ouch!


Steve anchors the knobs holding the adjustable fence with threaded inserts. I just can't make threaded inserts work in MDF, so I installed T-nuts from the bottom.

I also improved the sliding fence, although you can't see it in these photos, since I didn't get my first attempt right. It was a "Duh!" moment when I realized I had drilled the holes in the wrong piece of fixed fence, and the Festool clamps were dragging on the top of the sliding fence. I just redrilled the holes in the other side of the fence. The reason I use the Festool clamps is that they're light weight, don't take up much room, and I have less tendency to bump into them than if I use the F-clamps that Steve uses. And, I happen to already have a few of them.

When you include the new Bessey adjustable toggle clamp, as Steve does, it performs almost flawlessly, conveniently and safely. For mine, I provided an option to replace the Bessey with a home made holddown. This is mostly for illustrative purposes, as I have the Bessey and envision no real reason to use anything else, at least not for typically sized table legs. The Bessey's are pretty expensive, at around $20, and if you accidentally hit one with your saw blade, your SawStop brake would trigger, ruining the brake, the blade, the clamp, and your day.


Here's one more tip: When you put the jig away, clamp the loose part of the slide where you would put a table leg so you don't lose it.

Re: January- what are you working on?

#28

Re: Slinkies!!

Bruce McCrory

I got a feeder that hangs on a wire with a cool cone cap over the clear plastic seed bin. Guaranteed!! [Ya, Shurrr] For a week the rodents did back flips off the roof.

Then, one day it was spinning and flopping. A little stinker was inside the bin, looking at me. He pulled the roof up the wire and crawled in.

When we get rich we'll invest in slinkies and a pole model.

Right now, it's humming bird feeders. The Anna's stay all year (Seattle, WA). Squirrels seem to only guzzle sweet stuff in the summer.

Re: January- what are you working on?

#29

craigd

Re: Joint Stool

craigd

Thanks! White oak is just wonderful wood, I love it.

No, the top is one piece (sorta not really, it tapered more than I liked so I scarfed a wedge onto the bottom, it is the only glue in the stool). According to the Joint Stool book, if you need to make a two piece top, you just pin two pieces to the aprons.

I too, wondered about the the top shrinking but I guess it is small enough and QS oak so it works. Plus, the oak pins are amazingly pliable so they can bend and/or move the leg end grain. You can also pin into the middle of the aprons, which are free to flex. The stools stay together for hundreds of years so I don't think it is an issue.

Re: January- what are you working on?

#30

Trivits

Bill Tindall, E.Tn.

...or at least I think this is what you are talking about. I just frame a tile for these. I found some spectacular wildlife tiles in NZ and made some cherished 9x9" trivits. Wish I could find some more interesting ones. Saw some in a gallery but they wee $100!

Re: January- what are you working on?

#31

they are excellent to eat

Bill Tindall, E.Tn.

What is now subruban Egan MN was once corn fields and woodland patches and I spent many hours there thinning the population. My efforts have move to E. TN. With dumplings there is nothing better. Rabbits don't come close.

Re: January- what are you working on?

#32

Re: January- what are you working on?

Bill Tindall, E.Tn.

"oh, and earlier today i taught my dad how to sharpen his chisels and plane irons. he's a long time power-tool only woodworker, but i'm slowly corrupting him."

discovering what a sharp tool can do will do the trick.

Grinder- presuming you have not had previous experience. They throw grits around the area. I have banished mine from the hand tool area. These grits find their way onto the surface of boards and do the job on a plane bottom, blade, etc.

Re: January- what are you working on?

#33

Re: Trivets

William Duffield

Yes, a trivet is what it is called. It has no internal heat source.

When I built mine (I should build some more, because they had been popular), my concern was that someone would decide that since the majority of it was ceramic that they could set a very hot pan on it, and I didn't want them to ruin the finish or even burn the wood. Therefore, a standard frame, with the tile recessed within it, was not an appropriate design. Of course, thinset and grout, like your plant stands, is appropriate. The trivets I've made, with the tile slightly proud of the wooden frame, and held in place with a few spots of hot melt glue, have held up well.


This one is purpleheart, with two 6" square handpainted tiles with scenes from Rye, Sussex, England. Overall dimensions are 6-3/4 x 16-1/2" x 1". Like a window, it appears a lot less complicated from the front. From the backside, you realize that stock in three different widths is necessary, and you see the application of beads of hot melt glue.


Tiny dovetails join the handles to the frame. The other joints are dadoed and pegged. I should have used mortise and tenon, but that was a long time ago.


Here's another one I designed and built. The customer chose the tile. The tile suggested the style of the frame, which is cherry, with inlay banding.


Let's just leave well enough alone the glaring misalignment of the inner stiles with the feet. It looked just right before I cut the rabbets. :\

Re: January- what are you working on?

#34

Re: January- what are you working on?

Sgian Dubh

This is my next project Bill. A speculative piece for an exhibition in Manchester, north-west England in May. It's a horizontal tambour fronted sideboard with a stack of five centrally located drawers behind the tambour, and some adjustable shelves either side of the drawer stack.

I haven't yet decided if I'll incorporate the horizontal running wavey line indicated in the drawing: the line shows the junction between a dark wood below the line and a white wood above, meaning two wood species would be joined to make up each stave of the tambour. Another option I'm considering is the use of a white wood for every tambour stave, eg, maple, and then dying each stave slightly differently so the colour goes from white at the centre to very dark at the outer limits. The S shaped centrally placed line merely indicates how the middle two staves are profiled to form a handle or pull for the fingers to get a purchase so that the tambour can be opened and closed.

All the internal woodwork, except for the drawer fronts will be white, maple or European sycamore for example. The drawer fronts and all the outer carcase will be cherry, with the exception of the aforementioned tambour staves.

There's a reasonable chance I'll cut some of the grooves and other profiles or mouldings on a CNC machine. I see no reason why not as the drawings are in AutoCAD, and I have access to AlphaCAM and a CNC machine. None of that sounds very 'Hand Tools' I'm afraid, but I've been wanting to try out some CNC work for quite a while. Slainte.

Photobucket

Re: January- what are you working on?

#36

Question

Bill Tindall, E.Tn.

Autocad is another leap I have considered but not taken. Never found an instruction manual I felt I could easily learn from. The case at hand leads to a question. For my taste had I drawn by hand the swell on the verticals they would have appeared (perhaps incorrectly) to be too much swell. Diddling with this facet of the design is difficult by pencil and paper and I always feel like I have just given up rather than reaching an optimum final result. Is optimizing something like the swell of the verticals something readily done in Autocad?

I would love to build stuff like this if only I cold design it. BTW, there is no shame in using CNC, especially when it leads to novel designs impractical to execute by other means. I recall the jaw dropping stuff some student was posting on the other Forum last year.

Post some progress pictures.

Re: January- what are you working on?

#37

Tile insertion

Bill Tindall, E.Tn.

Many tile have a slightly rounded edge. I leave the tile proud of the frame by this amount, be it a plant stand, trivet or table. Indeed, it effectively keeps the hot or abrasive stuff off the finish. I like the hot melt idea

Re: January- what are you working on?

#38

Re: Question

Sgian Dubh

AutoCAD isn't a particularly easy programme to learn. My skills are very basic even though I've been diddling around with it for a few years. The challenge I found was getting time to really concentrate on it for an extended period. I found recently that I could devote about a week of almost uninterrupted practice. That was the key for me in that it gave me the chance to more deeply embed in the memory the necessary steps you have to take to create a drawing. All the same, my skills are very limited as I said, and I can just about use it now for creating basic orthographic projections.

What I do like is the ability to copy, mirror and move objects once you've got one example of the thing right. For instance, those legs you asked about, once I'd got one as I wanted it all I had to do was use those commands just mentioned, ie copy, mirror and move. In actual fact what I did was draw just the left half of that front elevation I put in my post earlier, and then I simply mirrored it.

As to the curve of the leg I drew the 70 mm width of the blank, put in a horizontal line at an appropriate height that intersected the outside edge of the leg, and used the arc command to create a couple of arcs where that horizontal line intersected the vertical edge of the leg blank. After that there was a bit of trimming and deleting and the profile was done.

However, when I actually come to cut the wood I'll probably work full size and just bend a bit of thin stick around a couple or three carefully located pins to get the curve to create a jig. On the other hand, I might use the CAD drawing and transfer the profile into AlphaCAM and knock out the jig profiles on the CNC machine. I haven't decided which way I'll go yet. Slainte.

Re: January- what are you working on?

#40

Re: January- what are you working on?

Jim Richmond

I just got done making an oval Chippendale footstool with ball & claw feet so it was time to clean the shop and tidy it all up. Now I'm trying to complete the tail vise on my bench, make some mods to a platform bed, help a friend finish a doll dresser and chair her grandfather made her and get some time with some new tools before starting a guitar for a friend in the next month or so.

Re: January- what are you working on?

#41

Thanks gonna borrow design for SWMBO


Re: January- what are you working on?

#42

Re: Thanks gonna borrow design for SWMBO

William Duffield

I can provide you measurements directly from the purpleheart one, if you need them. The other one would be more difficult, but not completely impossible. Scantlings may be more useful to you than overall dimensions. In any case, you need to start with the tiles and build the frames to fit.

Re: January- what are you working on?

#43

Ha, better say that again

Bill Tindall, E.Tn.

"In any case, you need to start with the tiles and build the frames to fit."

Imagine my amazement to discover that "9" tile come in a nearly infinite variety of sizes. They can look like crap when resized because the rounded edge is gone (presuming your son in law has a tile saw).

Re: January- what are you working on?

#44

Ottoman to match a Morris chair.

Chuck Nickerson

The design is done and stock has been rough dimensioned.

The hard part is finding matching leather for the ottoman's cushion.

I'm also building out the interior storage for a toolchest.

Re: January- what are you working on?

#45

And they look even worse if he doesn't   


Re: January- what are you working on?

#46

Re: Question

jack curtis

For some strange reason I just don't get CAD programs, even Sketchup, and I was a software developer who got most everything else. So while I can muddle about in Sketchup, I never found it easy or clear to use. I've returned to drawing by hand.

Re: January- what are you working on?

#47

Re: Question

Sgian Dubh

There's no harm in "not getting" CAD in many ways Jack. It depends I suppose on what your needs are. I like drawing and sketching by hand, although I wish my skills were better-- time to practice those skills has always been a problem as is the case with many things. Still, if you use CNC machinery in your woodworking, as we do where I work, I think it's useful to have some knowledge of how to get the ideas out of your head, into a drawn format, and then on to the CNC machine that works the wood. AutoCAD does that through the link to AlphaCAM, but it's more difficult to get hand drawn sketches or drawings into a format the CNC machine understands. No doubt you are already aware of all that anyway. Slainte.

Re: January- what are you working on?

#48

Re: Trivets = 3 = flummoxed

Bruce McCrory

I am old school now!

When I was growing up, trivets had three feet--tri--like tripod. I guess dairies don't have three legged stools; but the plant pots in my yard use three pads. Most people spend 33% more than they should for ceramic pot feet.

It's not really very tricky to level a pot, or prevent rocking when it is on tri-pads. However, try doing it with four.

Re: January- what are you working on?

#49

Re: Question

jack curtis

Oh, yeah, fortunately my career is now retired, so it doesn't much matter whether I understand CADD, except I'm trying to specify some major house remodeling, including doubling shop size. That would be a lot easier in CADD.

I also think this a very strange thing. I'm great at architecture and other spacial structures, simply see how it will go, and have a very logical, rational mind. And yet, every CADD I've tried is impossible. Maybe I should take a stab at inventing a CADD system I can use, may be universally applicable.

Re: January- what are you working on?

#50

Re: Trivets

William Duffield

The first picture I posted has gone missing, and I previewed it just before I posted it. Here it is again.