New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Face Vise Appliances for Tapered and Beveled Stock *LINK*

Posts

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#26

Re: What about in the olden days?

Warren in Lancaster, PA

Jigs are usually associated with machine work. In my 1880 Unabridged a jig is just a dance, but I think that this is about the time the word jig was starting to be used for a "contrivance to guide a tool". Here is what I do to taper legs.

I mark the bottom of the legs with a marking gauge. I mark the upper edge of the taper on the inside faces (doesn't show from the front) of the legs with a knife and square. Then I mark the taper with a straight edge from these two sets of marks. A pattern takes too long to make unless you are making many identical pieces. Except when it is a trivial taper, I saw with a ripsaw and then plane to the line. Then I mark the taper on the other side on the newly planed surface. There is no point in any remarking. I don't put the tapered leg in a vise.

Ripping is an art. It is a lot easier for a beginner to learn to make neat blind dovetails than to learn neat and efficient ripping. I chuckle a bit when people write that apprentices did the ripping and masters did the dovetailing. You want to saw as close to the line as you can without scarring the wood on the good side of the line. A nice job ripping will save time in planing. And the time spent using a ripsaw is not wasted. A worker who is well practiced with the ripsaw will be more skilled at sawing tenons and other precision work.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#27

The knife marks

Wiley Horne--So. Calif.

Thank you, Warren. I see now how to mark efficiently, rather than just mark everything and remark as needed.

I would not have thought of making knife marks at the top of the taper. Used pencil when I did it before, on the intuition that permanent cross-grain cuts could ruin the legs. But I can see where those marks can remain as important references for locating the lower rail (in front), the sides, and the back. And a bead or moulding or band, if used.

Very helpful!

Wiley

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#28

sawing question

Bill Tindall

do you saw from top of the leg to the bottom, or the other way around? I can think of theoretical advantages and disadvantages either way. With the band saw I go from top to bottom because I don't like to run out the side on a cut. And indeed, marks at the top of the taper are critical references.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#29

Re: sawing question

Warren in Lancaster, PA

I usually start the cut at the bottom of the leg. It is easier to get a straight start. When I get to the top end I stop when the waste falls off, which may be an inch or so from the end. I probably have done it from the top also, but it is likely easier to ease into the cut with the band saw.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#30

Re: Face Vise Appliances for Tapered and Beveled S

TomD

More is always better, but those are some pretty descriptive photos. Thanks!

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#31

more sawing question

Bill Tindall

How is the leg held? As I think about the task I can see that it would be wiggly held vertical in a vise (at least a small tapered table leg), given that rip saws usually have aggressive teeth. But I don't see how to hold it horizontal either. It doesn't seem like a difficult task to do once one figures out how to immobilize the leg. Even I can saw near a line, and since the planing is down hill, readily plane to the line.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#32

Re: more sawing question

roger lance

maybe you could invent some kind of jig to hold it.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#33

Re: What about in the olden days?

TomD

"One of the main advantages in either the band saw or table saw approach is that, if you start with a dead square blank, then the saw is keeping you square because it's square. But in the old days, this built-in squareness was not a given."

I'm no historian, but I would assume it was possible to get perfect results with hand tools, just as they made guitars, for instance, to very fine dimensions where required. Making squares square is super basic. In this particular case you only need one 90 degree surface to be super precise. You can then waste the first side with a draw knife. Keep in mind that in order to have nice looking tapered legs you have to align the grain well, or they will end up looking splayed, or bent. It works out that any of the ways you align the grain will make drawknifing easier.

Then you can line up the pieces and plane all four ramps at once. With a wider worksurface it should be easy to keep them level and similar. Same kind of thing can be done with the second sides, though they will be a little more difficult to deal with since they are already tapered on one side.

A good way to lay out the tapers is to lift one end up on a block, and use a pencil or scribe off the deck to set a level waterline.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#34

I wondered about that

Bill Tindall

for a small leg I'll bet wasting the taper with a draw knife would be quicker than sawing, at least with a straight grained wood.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#35

Re: more sawing question

Warren in Lancaster, PA

I hold the leg on a trestle with my right knee. Very secure. My trestle is 19 inches high. Here is a painting from 1816 that gives the idea. This guy looks a little awkward.


img

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#36

Williamsburg 

Warren in Lancaster, PA

Here is a picture from the Hay shop. Might be David Salisbury


img

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#37

OK

Bill Tindall

I can see how starting from the "floor" end of the leg would enable this approach. I was trying to imagine hanging the edge of the leg over something, but here the end of the leg can overhang. I think I could even do it with a sharp rip saw. thanks.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#38

Hats!?!

Bill Tindall

Why would someone in 1720 wore a hat in a shop unless it was winter?

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#39

Diderot ripping

Warren in Lancaster, PA

Here is another historic method illustrated in Diderot. This fellow is using a frame saw with the work secured to the bench with a holdfast. I think the engraver has the worker a sawing a bit too far away from the bench (too wobbly) and most other illustrations have a somewhat smaller saw.


Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#40

Top chef front and center...

david weaver

Guy in the front must be top chef. His hat's the tallest. They look like they could take a break around 9 and work in the kitchen.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#41

Gotta love that saw

Bob Hackett

For folks like me a saw like that makes all the difference between control, fatigue, and ease in following a line not to mention tylenol and a heating pad at the end of the day.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#42

Re: I dub thee "Sir Emmental" ...

William Duffield

At least, I didn't put a dog in every dog hole. I didn't even consider it. :D

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#43

Re: I dub thee "Sir Emmental" ...

roger lance

William....don't bring up the dog hole thing.... :)

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#44

Or a proper (one-bevel) hatchet