New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Face Vise Appliances for Tapered and Beveled Stock *LINK*

Posts

Face Vise Appliances for Tapered and Beveled Stock *LINK*

#1

Face Vise Appliances for Tapered and Beveled Stock *LINK*

William Duffield

If you don't have a patternmaker's vise, but need to hold tapered, beveled or round stock, or square stock at a 45° angle, there are some relatively simple and inexpensive alternatives.

I have built auxiliary jaws that drop right into the wooden chops I have attached to the metal (cast iron) face vise found on many woodworking benches. These appliances work for Record, Jorgensen, Colombian and Eclipse vises, to name a few.

For clamping tapered stock, when the taper is horizontal:


You'll need some 3/4" dowel stock and a 3/4" cove bit (core box bit) for your router. Cut a vertical half circle cove in the front chop. Cut a matching cove in the pivoting jaw appliance and glue in a section of dowel.


For clamping tapered stock, when the taper is vertical:


Cut a horizontal cove in the rear chop. Cut a matching cove in the tilting jaw appliance, and glue in a section of dowel.


Note the three notches in the bottom of this jaw. It is best to cut it a little wider than you need, so that when it rests on the vise bars, the dowel doesn't quite engage the cove, and then remove the notches with a rasp, until it rests on the bar with the lower bevel parallel to the rear chop. Thus, you need one less hand to hold it in place while inserting your tapered stock.

For clamping tapered and beveled stock, for example a tapered leg for a bow front table or sideboard:


Use both of the auxiliary jaw appliances you just made. Here''s another photo, showing the two jaws clamping tapered, beveled stock.


When making these jaws, I find it easier to cut the cove before cutting the bevels.

For clamping round stock:


For clamping smaller diameter stock, these blocks are reversible:


They drop right in, and hook on the left side. The hook keeps long, heavy stock sticking out the right side from from pulling them out of the vise jaws. In case you want to hang something out the left side of the vise insead of the right side, you can turn them around, in addition to swapping their order.

When you lay out the V-slots, make sure you leave plenty of wood at the bottom of each V, and don't line them up, back to back. I snapped in two the first pair I made. If you want to get really complicated, you can use these with one of the taper jaws to hold tapered round stock.


For clamping diamond shaped stock, for example shaping or carving a cabriolet leg:


Use the v-blocks that you made for round stock.

These appliances happen to have been made for my Loxiliary Meta-Bench, but they work just as well on any face vise on any cabinetmaker's bench.

I didn't invent these ideas. The jaw with the vertically pivoting axis was adapted from one made by Steve Latta, and his idea probably came originally from the often missing attachment to the Emmert patternmaker's vise, a reproduction of which is sold by Patrick Leach. (See link, but note that the Emmert appliance will not work with a regular woodworking face vise, because it has a center post that goes through a hole in the back jaw of the Emmert and is pinned in place so it won't fall on the floor.)

Of course, V-blocks are standard appliances for machinists. All I did was to adapt the ideas to materials I had on hand and the tools often found in a woodworking shop, and fitted them to the available vise and to the bench I was building at the time. They seemed intuitively obvious when I was building the Loxiliary Bench.

Here is a photo of Steve Latta's bench with the auxiliary jaw in place. He is laying out banding and bell flowers on a bow front Federal table leg. If the angles look a little skewed, they are. The beveled front face is up, and the leg is tapered on the bottom and inside faces. Steve only needs one tilting jaw because he is not going to decorate the side face of the leg. You can see one jaw of the F-clamp he is using to clamp the leg of his auxiliary bench to the top of one of the Hay Cabinet Shop Nicholson benches.


I have also built auxiliary jaws for my patternmakers vise that are also equipped with horizontal and vertical V-shaped grooves for holding leg posts at a 45° angle. These are very useful for carving legs that are symmetrical to the corner of the piece of furniture. I'll leave it as an exercise for the interested apprentice to figure out your own solution for the front legs of a Chippendale claw and ball chair, in which the outside side face of the post is typically at about 82° instead of 90°.

Déja vu? This is a repost of a response to an esoteric discussion of mechanisms for keeping jaws parallel on leg vises. It was suggested that it mightbe of more general interest, so here it is.


Leach's Tilting Jaw

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#2

Some excellent designs here


Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#3

Re: Face Vise Appliances for Tapered and Beveled S

TomD

Do you have more pics of the bench in general.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#4

Re: Face Vise Appliances for Tapered and Beveled S

roger lance

Somewhere long ago and far away, I saw the horizontal taper appliance and was impressed by it then as now. I'll be looking thru the scrap pile for stock to make this device. It will come in handy. Thanks for posting this material.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#5

Re: Face Vise Appliances for Tapered and Beveled S

William Duffield

I have lots of pictures of this Loxiliary Meta-Bench, and also a few pictures of a few others. They mostly will require a bit of processing to get them down to 100 Kb, so it would be helpful if I knew what specific details you were looking for, so I knew which ones to post.

Here's a start:



Here's an enticing photo of the undercarriage, demonstrating a method for holding it down on a joiner's bench, and hints of the vise mounting arrangement, and the back side of using a holdfast to hold a piece of wood to the front face.


HTH! I also have photos of more construction details, work holding arrangements, and accessories. If I don't have a photo or a measurement of a detail you are interested in, it's easy to go out to the shop, get it, bring it back in and post it.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#6

I dub thee "Sir Emmental" ...

Derek Cohen (in Perth, Australia)

The eyes of the Swiss cheese industry are upon you! :)

That is a bench with just one purpose in life.

Regards from Perth

Derek

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#7

Re: I dub thee "Sir Emmental" ...

William Duffield

The TransTint Honey Amber was just what the rock maple needed to complete the effect. :D

At an L-N event where I was showing it, someone quipped "a Swiss Army bench." My immediate retort was "More like a Swiss cheese bench."

Like clamps, you can never have too many dog holes.

And what would that one purpose be? I can count at least four purposes: holding any wood anywhere and any way, relieving back pain when doing detailed woodworking, taking up space on my joiner's bench, and as a serving/cutting board at wine and cheese parties. :D

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#8

Re: I dub thee "Sir Emmental" ...

Joe Rogers, Northern Virginia

Sir Will, I see you practiced on the (ahem) Black and Decker Workmate to perfect the process... :D

JR

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#9

Re: Face Vise Appliances for Tapered and Beveled S *LINK*

Paul M.

I wish I would have seen this a few months ago! I'm building a bench and need a vise that can handle tapered stock for guitar neck shaping. I wound up buying a wilton vise that has a similar horizontal tapering mechanism built in. I would rather have a wooden taper method like you have used compared to the steel one on the vise I'm building. Nice work!

Link below to the vise I bought and am currently building onto a bench...


Wilton vise with tilt face

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#10

Re: I dub thee "Sir Emmental" ...

William Duffield

The work-mutt was left out in the rain, and at the stroke of midnight the "hardwood" top turned back into termite barf, so I had to do something. If you've ever tried to clamp something with the plastic pitt bulls in the dogholes in a stock work-mutt, you know that there's never a dog hole where you need it, so (in my best Tim Allen impersonation), "I fixed it." The new jaws are 8/4 rock maple, just like the Meta-bench, and the holdfasts hold well in it. I also use it as a platform for my JET mini-lathe. To do any serious joinery on it, even with the Meta-banch on top, it needs some more ballast on the lower shelf.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#11

The scrap pile came thru....

roger lance

I'll be looking for some other pieces of scrap to make other vise aids....again, thanks William....


This device will come in handy this winter as I plan to make a dining table with tapered legs.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#12

Re: The scrap pile came thru....

William Duffield

Roger, You made my day!

How are you planning to taper the legs?

Stay tuned, because last weekend I attended another presentation given by Steve Latta. I think I mentioned it in another thread. One of the appliances he showed us was a leg tapering jig for the table saw. It is relatively easy to make, gives very precise results, and it is safe to use, unlike the gizmos sold by most of the woodworking stores. I took lots of notes and pictures, and plan to be building one of my own in the next few weeks, so will have personal insights into building it and making it work.

Until I saw Steve's, I had given up on tapering legs on the table saw, and had resorted to sawing them close on the bandsaw and finishing them on a power jointer followed by a pass or two with my #7, or doing the whole operation with the jointers.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#13

Tapering jigs......

roger lance

The first is a tapering jig for the tablesaw. The wide enclosed part sits snuggly over your saw fence. I designed this based on one by Norm Abram but added the fence enclosure for added accuracy/safety. I used a little two sided turners tape to help hold the work piece against the jig.....


The second is for the bandsaw. The problem with making a proto-type is that you may over make the thing which I did largely because I had the hardware laying about. There is a guide bar that rides in the miter slot of the bandsaw table and the jig was trimmed off by the bandsaw blade so the edge of the jig is where the taper will occur. I like this jig more than the one for the tablesaw: 1) the workpiece rides on the jig 2) the bandsaw has greater capacity of cut (6" vs 3") and 3) its safer - the cutting force is down toward the table on a bandsaw vs at you with a tablesaw. Just don't over make the thing....


Hope I got to return the favor.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#14

Re: Tapering jigs......

William Duffield

Roger, you've got some good ideas there, and also some examples for analysis and critique. I studied the photos I took at Steve Latta's presentation, and I missed some details that are important for anyone building one of their own, but that need pictorial explanation, not just text. So, I will need to take some more photos while I'm putting mine together. The problems with lack of support, especially vertical, that your TS jig illustrates are exactly the problems that keep me from using the jig I have hanging on my shop wall. Your BS jig can also be adapted to use on the TS. I agree, you should be careful not to overdesign and overbuild jigs. Steve's uses two knobs and one toggle clamp, but his toggle clamp is one of the new Besseys that self-adjusts for thickness. Steve also uses a different methodology for holding the jig against the fence, but it is necessitated by his school environment, with multiple table saws with different size fences.

Is it OK if I use your photos when I post the results of my build? I'll start a new thread, where all the info will be more easily found.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#15

Re: Tapering jigs......

roger lance

William....feel free to use these photos and I could e-mail more if you want other angles or have a jig broken down in parts for illustration. Perfection is a difficult goal to reach....even in jig making. I always had a little sense of caution with the tablesaw jig....never had a bad incident, but that style of jig is very capable of having a problem....not very much would have to go wrong and there could be a kick back etc. That was my motivation for making the second jig and turning to the bandsaw which is a safer platform for this type of cut IMHO.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#16

I never saw the need for a jig

Bill Tindall

For most applications I just taper on the jointer. Alternatively band saw the leg and plane out the saw marks if the taper involves removing a lot of wood like for a large leg. For the number of tapered legs most us will ever make in a lifetime making a jig for the table saw isn't an efficient use of time and a scary(to me) way to make legs to boot.

With my at best average hand skills I have no problem following a pencil line with a band saw. A jig for a band saw doesn't seem to offer any benefit over just free hand sawing followed by planing or jointing. Planing is always going "down hill" so even I have success at this kind of planing.

High precision isn't necessary for a tapered leg. One can't see a 1/16" difference between tapers unless the taper goes to a very slender tip.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#17

Re: I never saw the need for a jig

roger lance

that would be the contrary point of view.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#18

No, it is additional information

Bill Tindall

Nothing contrary about it. The purpose of my reply posts are rarely to argue with the original poster. Rather, their purpose is to provide additional information to onlookers.

To someone that has yet to taper a leg their choices to consider, at least, are to make a jig, do it on a jointer, saw with a band saw and plane or joint it smooth. Given the times I see the jig approach advocated someone yet to experience the making of a tapered leg could easily believe that this was the only reliable, easy, or what have you, way to make a tapered leg. My purpose is to proclaim it is not. While it could be a reasonable way to make many legs it is neither a quicker, more reliable nor safer way to make a few (four typically).

I have made tapered legs for several tables and have never employed a jig so it is undeniably possible to make legs with out this aid. It is up to others to decide among these choices what is best for them. Personally, I would be uncomfortable jig sawing them on a table saw using the typical jig.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#19

Re: No, it is additional information

Bruce, a MN Galoot

I've made maybe 8 - 10 tables with tapered legs and have done the tapering just as you describe, Bill. The one time I really needed a taper jig was for the strips for my canoe, 80 of them. I wanted full-length strips, at least 19' long. (I didn't want to use butt joints). That meant that I had to make 160 scarf cuts. The jig I came up with to make those cuts wasn't particularly good, but it got the job done. The problem was that I couldn't figure out a way to hold the strips rigid as close to the blade as needed.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#20

Jack Guzman from Maine

Actually..

Jack Guzman from Maine

that's how I do it. I got one of those flimsy aluminum taper jigs years ago but when I tried it the process was too unreliable. I just draw my lines,rough saw and finish off with a plane. Too easy to even question.---Jack

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#21

For the record.....

roger lance

There are times I use a jig.....and times I don't. Like the horizontal taper appliance for a vise I made above.....no jig used. Use one or don't.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#22

Re: I never saw the need for a jig

William Duffield

If you just want the legs tapered, you'll get close enough that no one will ever notice using those techniques. However, if you are planning to add stringing, cuffs, bell flowers, etc., small discrepancies can show up when accentuated with precision decoration.

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#23

Amen


Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#24

What about in the olden days?

Wiley Horne--So. Calif.

Does anyone know--or have a pretty good guess--as to how leg tapering was done by busy cabinet shops in the olden times, say, circa 1800? Of course, one answer is that they got real good at sawing.

However, I doubt that 'good sawing' is the whole story. For a couple reasons. One is that for a Federal-era shop, say, every Hepplewhite-type leg was tapered. So there were many of those to make, and every day--not a 'once in a while' operation. Second, as you saw the tapers, you're progressively sawing off whatever marks were on those faces. It breaks your rhythm and it's no fun to stop and remark the face you've just sawn. And as you get further into the tapering, you've got to keep track of your reference face, too, so that the leg will close on itself square on all sides. Third, some of the legs, like on certain secretaries and worktables, had a 'bulb' (what they called a 'therm foot' in those days) located a few inches up from the ground. So they couldn't always simply saw straight through, unless that bulb was applied (glued on) after a straight-through tapering.

One of the main advantages in either the band saw or table saw approach is that, if you start with a dead square blank, then the saw is keeping you square because it's square. But in the old days, this built-in squareness was not a given.

So what did they do? I could imagine a shop using some kind of a jig, even an elongated miter box and a 30" long saw to cut those tapers. Or failing that, some kind of a fast marking jig, like a taper nailed to the wall, that you could walk over to and quickly mark your faces as you saw.

I raise this because for various reasons, I've got four legs coming up that will be done by hand. I've done it before, and with the therm foot, but it's a difficult and sometimes nerve-wracking business when you have no training.

Thanks for any ideas,

Wiley

Re: Face Vise Appliances for Tapered and Beveled Stock *LINK*

#25

Re: I never saw the need for a jig +1

TomD

Tapering jigs and circle jigs seem all the vogue on the TV shows, but I use the jointer method, or the saw and shave method, or drawknife. Whatever blows the wood off fastest. Jig storage room I do not have, and I do not make enough parts that a jig is worth it. I did make a tapering jig for little wedges for a bookcase. That was worth it even for just a dozen.