New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Squares

Posts

Re: Squares

#26

what sort of caliper do you speak of?

Bill Tindall

The statement I made was " I don't see how they are any less accurate for measuring than any alternative ruled instrument." I had in mind rulers. But, if you mean a vernier caliper, if anyone still uses one, then I concede that a high quality vernier caliper could be considered a ruled instrument and that it is 2X more accurate than the ruled square described.

Of course for precise measurements where 0.001" is relevant I use a digital caliper because I can see the measurement better than with my vernier caliper. It is surprising how often I use the digital caliper. For example, it, plus a set of number drills, results in reliable pilot holes for screws and brads.

Re: Squares

#27

Now $89 for the 4 squares.

Bill Tindall

I just checked and Galdstone is still on the internet. I think it is run by the son. The set of 4 squares I bought is now $89. And I see he has a hooked rule for a price I will pay. I was told that these squares are ruled by the same place that rules Bridge City tools, but I have no way to confirm this claim.

Re: Squares

#28

Square measuring.....

Bill Tindall

Some thought it at least strange that I measure with a square. So, I thought, next time the task comes up I will document the process to better judge how inappropriate, or not, it is to measure with a square.


I didn't recall how thick I had made the top drawers. I had within reach an assortment of tape measures (if you have 6 one can usually be found handily), a hook rule with the hook broken from dropping it on its frail hook, a folding rule I have never used, a digital caliper and various ruled squares.

The answer is 1/32" bigger than 3/8" ( that is the way I record measurements in my head). The square against the side reliably and quickly sets "zero" and reading the scale directly above it is sufficiently free of parallax to be suitable for the need at hand. I remain convinced this measurement is as handy and suits the need as well as any alternative.

Re: Squares

#29

Re: Square measuring.....

Dean J in MN

OK, but why did you need to know how thick the drawer side was as a number?

If I was making a mating part I'd just set my gauge with the drawer side itself and transfer that to the other part. Working by hand I really don't care the precise numerical representation of the size of anything. After the overall dimensions of a piece are set I rarely even pic up a rule.

Just a matter of shop practice, I just don't see the need for a ruler with finer than 1/8" marks, nor do I use a square in the way you do. It isn't a right-or-wrong, just a method of work.

-Dean

Re: Squares

#30

Re: Now $89 for the 4 squares.

roger lance

Bill....this is a fine appearing set of squares....my major interest in a square is not whether it is ruled or not but whether it is square....if I had run across this set of Gladstone squares when I bought my set of Sorbys, I might well have bought the Gladstones given both sets are equally square....as to measuring length/distance with a square, I do it as I stated with my Stanley (and other ruled squares), but other methods of measure give me more confidence in accuracy.

Re: Squares

#31

Answer.....

Bill Tindall

Because I was going to make the larger drawers a wee bit thicker. I am familiar enough with the scale on my thickness planer that given the measured thickness of this drawer side I can target the thickness of the last three off the planer scale. And before that, set the fence on the resaw. But don't get too critical of this example that the larger picture is missed. Squares are a handy way to measure when you need, or choose, to if you own ruled squares.

However, you make a point worth reinforcing. The less I measure with a rule the less I screw up making something to fit. I am in the process of learning to establish cut lengths and widths ever more by transferring such measurements from the case, for example. As a case in point, I measured with a tape the length of the false top for this case and managed to get the part too short by exactly one inch, a mistake I had previous encountered on other projects. Had I placed the roughed out top on the case and marked it, the length would have been acceptable.

Re: Squares

#32

Re: Square measuring.....

TomD

Yacht designers designated offsets, in pre-metric days (still with us) in 1/8th and pluses and minuses Like your 1/32, except less so.

I increasingly just make a wack at a measurement, like put a mark on it one way or another, then remember how the actual mark looked in relation to whatever, and just cut to that. So maybe I want an actual inch. I quickly drop the ruler on it, and mark an inch, but for whatever reason the mark is off a 64th. No problem, I just cut to the mark plus a visualized 64th. Comes out a lot more accurate than near enough.