New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

CPM 3V for bits?

Posts

Re: CPM 3V for bits?

#26

Thanks, Phil

Pam Niedermayer - Austin, TX

Many thanks, Phil, very informative. I am so happy my Makita will work.

Pam

Re: CPM 3V for bits?

#27

Re: My method hasn't changed much

Pam Niedermayer - Austin, TX

No, won't use the Makita for final anything. There is now that 6000 grit stone available, but I've got finer coming out of my ears. :)

I really appreciate your taking all the time writing such a full reply. I've saved it to digest as I progress (one can hope) with the real work. I think I understand it all, but applying it will take some practice and rote.

I also like the wet grinders, but dislike hollow grinds, thus the Makita. However, the swarf doesn't all go down the drain, even if I were lucky enough to have a drain better than a bucket. Most of it seems to spray itself around the area I've partitioned off. I can follow the line around the partition and across my shirt, almost like a laser ruled line.

Pam

Re: CPM 3V for bits?

#28

Angle grinders,my experiences (long)

Bob Hackett

I`ve been thru just about all the different brands except the ones from China,I refuse to touch those for religious reasons. ;^)

Dewalt,Makita,Porter Cable and Milwuakee are some electric grinders I have had good luck with.I prefer pneumatic tools but that`s just me.The electrics I usually get as factory rebuilds as they are far cheaper and carry nearly the same warranty.A new one is going to look like it`s 10 years old before the week`s out so why pay for new,eh?

A couple of tips while grinder shopping;Get one with a guarded slide switch or a safety paddle type switch so they can`t be put down and turned on accidentally.Once you`re done grinding your focus will be on the work not how you put the grinder down,trust me on this.

Look for a body design that allows you to easily blow the dust out of the area around the brushes and bearings and do this often.

Every grinder I buy gets the gear case opened up and the factory grease replaced with a lighter grade moly grease and the gearcase gets packed full of grease.I may have to wipe the grinder down occasionally to keep the grease that creeps out off the work but if grease is working it`s way out then swarf is not working it`s way in and I`m sure that the gears are getting what they need to stay happy.

A spindle lock is far easier to deal with than 2 sheet metal wrenches when it comes to changing abrasives.A good spindle lock can many times make switching things over a tool free process.Those thin wrenches get lost too easy and are never around when you need them,especially if you put them in your back pocket and then go nuts looking everywhere for them like I do.I have no acceptable excuse for this yet it continues to happen regularly.

Even with a good spindle lock make sure your spindle has flats on it that will accept a wrench.Stuff gets jammed more than you think and that spindle lock will only stand so much torque no matter how good it is.

Look at the amp rating when you buy,higher is better and more powerful.Even if you don`t need a more powerful grinder the higher amp rating means it`ll be that much harder to stall it and burn it out.

Think about ergonomics and things like alternate placement of that add on handle.Being able to change hands and always having 2 hands on the grinder is a good thing.A threaded boss on both sides and the top for that handle is worth paying a little bit more for,an infinitely adjustable handle is even better.

An adjustable guard is also a real handy item.Better to be able to move it than having to take it off completely and then have a wheel come apart on you.

Check online reviews and pay close attention to vibration.Low vibes mean a well constructed tool and one that will probably last.It also means you won`t need a death grip to keep control of it when your hands start going numb.

I would also recommend wearing thin gloves that will protect you from sparks,offer good abrasion resistance and increased grip yet don`t completely compromise your sense of touch.Cotton gloves are NOT your friend here.Either are synthetics,they usually melt and fuse to your skin when constantly bombarded by sparks,very distracting.

I tend to go with my leather TIG welding gloves or occasionally flame proof gloves with rubber grip palms/fingers if they`re on sale.I buy at my welding supply house.If they`re good for welding then they`re good to go for grinding.

I also wear either my welding leathers or a leather apron when grinding.That cotton sweatshirt will begin to smolder and then flame up under a steady stream of sparks and those synthetic coverall will melt just like the gloves will only this time it`s your torso instead of your hands that it`ll fuse to.

Get a quality face shield with replaceable clear plastic shields and wear you safety glasses w/side shields under it.It`s way cheaper than getting metal dug out of your eye.I speak from numerous experiences about the eye thing and that`s even wearing both safety glasses and a face shield.Again I have no excuse but it still happens,usually when I take the eye protection off and all the dust that landed on it and in my hair falls into my now unprotected face.Go figure.

Dont forget your ear plugs either,grinding is LOUD!

Re: CPM 3V for bits?

#29

David Barnett

I've been waiting...

David Barnett

... for my cheapo HF grinders to die on me so I could buy a couple of those fancy sturdy high-end grinders. I originally bought four of these when they were on sale for $8.97 each. That was years ago. Spindle locks, switchable side handles, and so on. No paddle switches, though.

Anyway, I keep Kutzall Extreme wheels on two, a cutoff and a flexy non-woven on the others. I use mine on wood and stone. Great tip on the grease. I'd try it, but it might prolong the waiting for their demise. I do wear viscoelastic anti-vibe gloves with these, though. What do you think about epoxy motor windings, btw?

Re: CPM 3V for bits?

#30

Epoxy motor windings

Bob Hackett

They smell really bad but burn really well once they get going and that plastic housing kicks in. :D

One of the reasons I like air tools is that I have two sons who feel free to help themselves to whatever they feel appropriate to the task at hand.Between the two of them they have been responsible for letting the magic smoke out of a phenomenal array of electrical tools.My friends and neighbors are pikers by comparison.

I don`t even want to think about the price tag for their continuing education.Lets just say I get cards and letters of thanks(and condolences) from most major electric tool manufacturers.The boys even get birthday cards with frequent flier points inside.Now you see why I started to buy rebuilts :^(

BTW David,those Horrible Freight angle grinders are a trick to lure you into thinking that the other things they offer may actually last more than 48 hours max.

I am currently sponsoring a bill before congress that will require a plainly recognizable likeness of Satan to be permanently embossed into any and all Chinese goods before they can be imported into the US.Sales among young people will spike but should be more than offset by the drop in sales from Christian fundamentalists once the televangelists see it.

I have absolutely no hope of sliding that last paragraph by Bill while in moderator mode but trust he will get a chuckle out of it before he launches it into the great beyond.It gave me great pleasure just to type it.

Re: CPM 3V for bits?

#31

The return of foot powered tools(may be OT)

Bob Hackett

I had an old potter`s kick wheel that I was considering turning into a large,foot powered horizontal disc sander,grinder,work holder(I was making stone bowls at the time) for a while.The post about using CI disc brake rotors as diamond substrate got me thinking about it again.

Luckily I had a ton of other things to do when I had it and allowed myself to be talked out of it by one of my potter buddies.

I may start casting around for another one.I know floor buffers were still too fast for what I wanted to do.Maybe I can trade the 3 buffers I have now for broke down old kick wheel. :D

Re: CPM 3V for bits?

#32

I will add...

John in NM

I do a lot of one hand grinding/carving, and really like a slide switch. The paddle is a pain for one handed work.

If you like to work this way another thing that helps is using rol-loc sanding discs, the holder for them makes a lot more room so you can choke up on the grinder. Guard no longer works though, just FYI.

Re: CPM 3V for bits?

#33

Re: The return of foot powered tools(may be OT)

Pam Niedermayer - Austin, TX

That would be something, maybe a little overkill. :)

Pam

Re: CPM 3V for bits?

#34

Why not make your own?

Bill Houghton, Sebastopol, CA

There are plans around for homegrown kick wheels - you could customize for your specific application.

If I were going to do that, I think I'd mount the brake rotor with the hub down, so you weren't having to work around a hub sticking up.

Re: CPM 3V for bits?

#35

Re: I've been waiting... *LINK*

Pam Niedermayer - Austin, TX

Yeah, the problem is HF is not reliable. The ones you bought some years ago may be very different quality from the ones sold today. Anyhow, the DeWalt I've tentatively settled on has a pretty low price and great reviews.

Thanks,

Pam


DeWalt 4-1/2 angle grinder

Re: CPM 3V for bits?

#36

Re: I will add...

Bob Hackett

The slide switch is also a plus when you want to put the grinder in a vise and use it as a stationary tool.I have wood jaws that wrap around the body yet do not block air flow to do this.

My sons just clamp the plastic body between the steel vise jaws and go for it till the grinder body breaks, and the grinder jumps out of the vise or the magic smoke appears,whichever comes first.Then they repeat the trick with the next one in the bin till either the job`s done or the bin`s empty.

When the bin`s empty they go find Dad who is always less than sympathetic to their plight (as far as they are concerned).Dad runs them both out of the shop,opens the windows so the smoke will clear and then when they`re not looking pulls another grinder from the hidden stash and finishes the job for them.Dad would hand them a file but he hates to see good files ruined and so far they haven`t touched the file rack(thank the Gods).

Re: CPM 3V for bits?

#37

Re: Angle grinders,my experiences (long) *LINK*

Pam Niedermayer - Austin, TX

Wow, many thanks, Bob. This DeWalt has a paddle switch, and the handle is a two-position one, but I think only via unscrewing.

I had planned to start out using hand files, hack saw and the Makita, even for initial shaping, moving to an angle grinder only if. With all your warnings about clothes and masks (thank you very much), this approach is confirmed.

Pam


DeWalt 4-1/2 angle grinder

Re: CPM 3V for bits?

#38

Probably just as well

Bob Hackett

You will note that in 2 of the 3 in process pics in the link you posted the clueless operator/model putting the grinder thru it`s paces is intent on burning the crotch out of his(hope they`re not synthetic) pants and impressing the ladies with both the size of his (soon to be blistered)package and his break dancing style.

Just goes to show,even with all the proper whiz-bang safety gear in place nothing is truly idiot proof.That`s because idiots are just so darn ingenious!

Re: CPM 3V for bits?

#39

David Barnett

Cheap thrills in the workshop

David Barnett

"They smell really bad but burn really well once they get going and that plastic housing kicks in."

That explains why my neighbor's Dewalt smelled funny. When my grinder gets hot, I switch to a cool one.

"TW David,those Horrible Freight angle grinders are a trick to lure you into thinking that the other things they offer may actually last more than 48 hours max."

It worked. I've had good, or perhaps bad (depending on how you're looking at it) luck with my few power HF tools, like their $7.99 heat guns (I buy two whenever they're on sale), the angle grinders and the one little drill press for smallish work, bought back when they were $37. I abuse the heat guns until they smoke and burn, roasting coffee with the end embedded in the beans, using it to stir. Tends to get real hot that way, heh. At that price I consider them disposables. And I actually love the drill press, with the least runout I've seen on anything less than a thousand dollars. I've put it through its paces, although most of the stuff I do is very light.

But yes, I avoid most everything at HF. Satan? That will increase sales among the hoards I generally see dazzled by tools cheap and chinoise. From what I've seen, however, The Devil is hardly a deterrent to a true cheap tool whore. There's limits, you know.

Besides, I really like those sort-of-soft 5-piece hammer sets they sell. Easy to modify, great for texture hammering. And the punch sets are great for repurposing, too.

Re: CPM 3V for bits?

#40

David Barnett

Re: I will add...

David Barnett

"I do a lot of one hand grinding/carving, and really like a slide switch. The paddle is a pain for one handed work."

I'm used to the slide switch and think the paddle might bug me. I do a lot of one-handing, as well. Yeah, maybe I'll stick with slides.

Re: CPM 3V for bits?

#41

David Barnett

Re: Probably just as well

David Barnett

Yeah, ya gotta be careful down there. Smoke emanating from one's naughty bits is usually a bad sign. Doctor asks:

"Do you always smoke after sex?"

"I don't know. I never looked."

Re: CPM 3V for bits?

#42

Re: Angle grinders,my experiences (long)

TomD

I don't know if you would like a grinder Pam. Based on some of the things you have a preference for you might not like it. They are a finesse tool, which you would enjoy, but they are noisy and quite dangerous. You can get everything from blades shattering to nasty kick back. I have to say I have yet to be hurt. All rotating abrasive tools have the same issue with kicking so if you have that feel grinders won't be anything new. That said I have two, and two bandsaws, and I never use the 4.5" grinder on my toolsteel projects, unless I am cutting already hardened HSS bit, and then I tend to use the Dremel.

If you really want to make a bunch of blades I would get a bandsaw off Craigs. Even the small ones only cost 150 new, and resale is probably 50-80%. Bandsaws with a bimetal blade will make short work of straight and curved cuts, and you could equip a whole shop with chisels and planes from one to 2 blades. You could rough out most of the curve on tight curves like Ogees with notching and relieving, leaving little for you files to do. Files are going to be really slow.

Hand held bandsaws are also really efficient, but they are quite popular so I don't know whether you would find one as easily.

Craigslist for Austin Elgin has a vert horizontal for 150, they claim it is older quality. Found it under "band saw" Just for instance. Bandsaw performance is at least 50% the blade, so if you go to try one out. Do not be surprised if it won't cut worth... until you put a bimetal blade in it.

Look at Harbor freight under:

Power Tools - Portable Band Saws $76

Metal-Cutting Bandsaw works both horizontally and vertically for the ultimate in metal-cutting versatility

Only: $269.99

Sale: $229.99

Mostly I use mine in vertical mode, and they cut steel about as safely and comfortably as possible. These tools don't have rubber tires because theoretically one is using oil, this tends to mean the blade derails every now and then. I just accept it, but there is an online instructional on how to fix it. It is not a dramatic even when a blade comes off, it just stops cutting.

Re: CPM 3V for bits?

#43

Good heavens...

John in NM

Sounds like my never ending and losing battle to educate my surrounding world with "The Proper Way to Clean a Paint Brush"....

I don't think I've quite reached your level of philosophical acceptance of reality though, but it's something to aim for :D

Re: CPM 3V for bits?

#44

Re: And

TomD

I haven't tried the HF portable, but I would be all for it compared to a 4.5 I would not expect it to work all that long, though sometimes that stuff is still working 30 years down the road.

Dremels will cut steel very effectively. The cut blades last about 30 seconds. The glass reinforced ones don't wear anywhere near as quickly. I would not consider one for bigger projects but if you have one already, it is worth knowing about.

Finally a pitch for O1. CPV makes sense these days. But i will give you a recent example of my tool lust. I was watching Bogdonovitch's Guitar DVD, and he did a lot of cuts with a double bevel straight edge chisel. It seemed real handy. In my shop I stock 3/16" O1, which is just perfect for that tool. At some point I will go out there, and in a few minutes saw off a piece of stock Because I invested 150 in a bandsaw, I can cut from wider O1 stock, which is much much cheaper than size specific stock, both in yield and retail price. I was put onto this. Almost all steel is sold on volume/weight basis, if you know the square inch price/weight, that is pretty much all you need to know. But with O1 the savings on wider stock are really significant so the saw pays for itself twice.

Anyway, a few minutes of sawing, and grinding, in the shop, and an hour or so finding the stuff and unearthing it, and I would have a finished blade as good as any I can buy. Virtually no skill required, no drama. For your smaller planes like the hollows and rounds your heat treating would be freeish for the cost of a brick, assuming you have a propane torch.

I figure on a one-off basis, the cost of heat treating is at least 8 bucks, and the same both ways for postage, or bout 10x what an O1 blade would cost me. Overlay Canada as a starting point, and the cost is likely much higher still. So at least for one offs, I am happy to have the option of O1.

Re: CPM 3V for bits?

#45

David Barnett

An alternative, at least short-term... *LINK*

David Barnett

... to Tom's bandsaw suggestion, which is really the way to go once you know what you're doing and what you want, is the hand tool route, of course. Easy pace, quiet, safe.

I'd add to files, though, a good jeweler's saw frame. I know you already have a hacksaw. When I made my first knives, I cut out the O1 with a jeweler's saw, which was not as slow as you might imagine. It was great practice for later piercing, enameling, and so on, too. I'd split the scribed line (Dykem Blue) and clean up with files. Worked great.

Besides a bandsaw, another power tool worth every penny in my shop is the 1"x42" belt sander with 8" disk. The knock-offs of the Wilton (expensive) are totally usable. The old Delta was cheap (less than $100) and at 62lbs, solidly built. Grizzly's H8192 is $159. The Jet (also expensive), is prettier and white. You can often find the Delta models on eBay and craigslist. I've been told the Delta will again be in production, but it's wait-and-see.

Anyway, these are terrific multi-use tools with all manner of belts for sanding, grinding, sharpening, stropping (leather), polishing (linen, nonwovens, felt), and more. I've used mine on nearly every blade I've made.


Truing briar on the disc

Re: CPM 3V for bits?

#46

It's like weeds and gardening

Bill Houghton, Sebastopol, CA

The idiots will always outdo the safety folks because they work at it full-time - like weeds in gardens. Also, stupidity takes less time than designing and testing safety features.

Re: CPM 3V for bits?

#47

Workin with "old scratch"

Bob Hackett

I bought an old rusty foot adze and while cleaning it up I found a trademark stamped into it that says "Hack Devil".Don`t know if it`s a warning or just a tool I owned in a past life coming round again.

Good steel,glad I bought it even if the maker`s mark is a little creepy. :)

Re: CPM 3V for bits?

#48

Re: Good heavens...

Bob Hackett

The wife taught me how to properly clean a paint brush.Apparently it begins before you even dip it in the paint.She was a fiend for keeping then clean,wrapped and properly stored.I`m a roller man myself and let me tell you you can sling paint laden water pretty far with a heavy nap roller and a pro type brush spinner.That`s a trick I shouldn`t have tried while my boys were watching let me tell you.

She could get 6 months of everyday use out of a good Purdy copper ferrule brush and still have it looking near new.Fabric softener and an old crock pot were her secret weapons to clean the brushes the boys used.They both worked for her for about a year before she couldn`t deal with it anymore.Luckily the older one got his attitude on and left to become a paratrooper in the 13th Airborne.

My youngest boy is a pretty fair plasterer and airless spray hand and knows how to keep those tools spotless.He`s not the fastest hand at plastering or drywall but he`s got a good eye and is wicked picky about how he works things like corners.The joints are straight and dead flat when he gets done with them.

His brother is a graduate of the slather it on and then sand it back off school of drywall. I caught him with a cigarette poked thru a hole in his dust mask more than once. :^(

Re: CPM 3V for bits?

#50

Um Bill...

Scott Burr in Ben Lomond CA

Stupidity takes less time Not necessarily...

Test and safety issues are mostly brought on by stupidly. There's over a million data points out there. That's a lot of dumb.