Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Pull Stroke Sawing - Vertically?

Posts

Re: Pull Stroke Sawing - Vertically?

#51

Re: Pull Stroke Sawing - Vertically?

Bill Tindall, E.TN

>Avoiding the risk of getting Bill stirred up I'll ask by email..........

I have been fret sawing (and fretting sawing) a bizzillion holes out of a fretted gallery. I have used a power fret saw/jig saw for most of the work but there are some tiny details that are too scary for the power saw. I have 0 experience with a hand fret saw and would have had-at the task with the board vertical in the vice and the saw horizontal. Do I correctly understand that this approach is off by 90 degrees? I should have the board flat and the saw vertical and the saw gripped as you describe in the picture? I didn't have patience to follow and understand the details of the shoulder and pivots discussion. I presume I make the saw go up and down how ever it feels comfortable?

I have seen fret sawed metal and I figure anyone that can do those holes knows what they are doing (and has good eyes). Speaking thereof, son-in-lay wants a magnifying light, one of those affairs with a lens and circular fluorescent. There are dozens of brands, some of which I am sure are junk. Any recommendations?

As an aside, one thing that gets lost in these discussions is the difference between someone sawing dovetails now and then and someone sawing them weekly. Reliability and speed are regarded differently between these situations and some techniques favor one or the other attribute of a technique. I'd saw standing on my head if it ensured precision.

Re: Pull Stroke Sawing - Vertically?

#52

Magnifying lamps

Bob Hackett

>Unfortunately I`m to the point where these are the rule now,especially for grinding/sharpening.

While I can`t make any recommendations as to brands(all mine are used models at least 10 or more years old)I can say thru experience if you plan to do anything with a light like this where there is a chance of sparks then a glass lens will be trashed in no time flat.I use lamps with polycarbonate or other plastic lenes around the grinders or wherever the sparks may migrate from my metalworking.

Some models have a sliding cover for the lens and these are handy to keep dust and grit off the lens.What little dust migrates under the cover can usually be just blown off the lens without wiping and scratching the lens.Bagging the lamp while not working helps if you find one you like without a cover.

The absolute best solution for my failing eyes seems to have been a magnifying eyepiece with headband.It goes wherever I go,even outside.There are replacement lenses with different power and focal length available.Most lenses are impact and scratch resistant so they become eye protection too.I also find snapping the lens out and cleaning in the sink alot easier that cleaning a lamp lens.

I just wish I had thought of the visor before I went thru the trouble of chasing down all those mag lamps.

Perhaps my eyes aren`t the only thing failing.;^)

Mainely,Bob

Re: Pull Stroke Sawing - Vertically?

#53

fret sawing

Warren in Lancaster, PA

>Bill, we generally work over a birds mouth, a small board with a v shaped notch in the end. The birds mouth is clamped to the bench and sticks out towards where you are seated. The blade on the fretsaw cuts on the pull stroke, the handle is underneath the work, and you look at the top of the board (the show side). For this kind of work I would usually hold the fretwork on the birds mouth with my left hand and saw with my right. You might be more comfortable clamping it down for each cut. You might break a few blades before getting the hang of it.

Re: Pull Stroke Sawing - Vertically?

#54

Re: Pull Stroke Sawing - Vertically?

Dan Donaldson

>For cutting delicate items like pearl, abalone, or other fine inlay materials, I use a board that I clamp to the bench so that it is horizontal to the floor and hangs out over the edge of the bench. I drill a small hole in an inch or two and then a slot from the hole to the edge of the board. I then place the item to be cut on the board and cut with the saw vertical. The board with the hole works as a zero clearance insert and the item being cut is always supported. I also have fine control of the saw and have the blade in the frame so that it cuts on the pull stroke.

BTW, If you ever try this with pearl or bone, be sure to wear a face mask as the dust can be very bad for your lungs.

I could go out and take a picture if it is not clear and anyone is interested.

Re: Pull Stroke Sawing - Vertically?

#55

Your description much better than mine ;-)

Dan Donaldson

>