Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

John Henry versus the steam hammer

Posts

John Henry versus the steam hammer

#1

John Henry versus the steam hammer

Wiley Horne -- So. Calif.

>Hi All,

In a thread below, Bill Tindall was characteristically lucid (not to mention blunt) in saying that he hadn't seen any evidence that olde-tyme forged blades were any better than modern blades provided by leading manufacturers such as Hock Tools, Lee Valley, and Lie Nielsen. That seems fair enough as far as it goes, but then there isn't much evidence to see, in terms of side by side comparisons.

My bias is that the best smiths can do things that aren't sensible for a heat treater to even attempt. Now up front let it be said that there isn't much true handforging of individual blades going on. Anywhere. How could there be? The smith has to make a living unless he was born into money, and if he was born into money, he wouldn't be a smith. So, like John Henry, smithing has by and large lost out to machine methods. Cause how many smiths can get $200 a piece for their blades?

But there is some hand forging going on, so on that basis I think the question can be put as to whether a smith can make a steel forging which is better than the leading commercial blade makers. 'Better' meaning that for comparable toughness and sharpenability, the smithed chisel will hold its edge better.

Why do I think it is likely that the top smiths can beat professional heat treating? The reason is that the smith is guided by phase changes he can see occurring in the steel, as they happen, whereas the professional heat treater has the steel on a program which is established by the clock and by thermostats (if this isn't so, someone please correct me). F'rinstance, the smith can see the hot steel shrink slightly and change color in the orange zone as it transforms into austenite with a different crystal lattice. By responding real-time to phase changes in the steel, the smith is can shrink grain size, use higher carbon concentrations (think 'more carbides'), and manage his carbide distribution so as to optimize edge holding, toughness, and sharpenability of the steel forging.

This is my bias. I know of only one study which tackled this problem*. That particular study did find that the smithed chisels performed better, but then that was more than two decades ago, and there are new market entrants now, including all of the ones mentioned in paragraph 1 above.

I do notice that certain small companies are trying to make a business out of handforged blades. Galoot-Tools comes to mind.

Any opinions or evidence one way or the other on smithing vs. professional heat treating?

Wiley

*'Testing Wood Chisels', Bill Stankus, in Fine Woodworking magazine, March 1985, Issue 51, pp. 44-48.

Re: John Henry versus the steam hammer

#2

Re: John Henry versus the steam hammer

Stephen Shepherd in the State of Deseret

>Wiley,

I can not comment on the difference between modern heat treating and nineteenth century forging techniques because I know little about modern steels. I can comment on nineteenth century (and earlier) laid steel blades.

I apprenticed in a cabinet shop with mostly European (German) craftsmen and many of them sold me their old tools. So I was exposed to quality laminated tools, plane blades, chisels, hammers, etc and collected and used them.

I also went through a number of metal Stanley, &c. planes and didn't like the feel, the blade, nor the look. I liked the old tools they felt better and I thought the steel was better, but what did I know I was an apprentice. That was over 35 years ago and since then I have learned that the steel apparently was better, the tools work better than any attempt at a modern solid steel tool that I have encountered.

I have had a bit of experience at a forge, I can make a forge weld, I have even got a piece of steel forge welded to a piece of iron, although it burned up while re-heating it. I have a respect for what a smith can do and they can tell a lot by the color.

The brine quench is still the smoking gun for hard old 'irons'.

I just picked up a blade from Chris at Galoot Tools and am just excited that I have a brand new laminated steel plane iron in my hands. Who would have thought. I also have a lot more respect for the laminated Japanese tools.

Stephen

Re: John Henry versus the steam hammer

#3

hammer refining of steel

Larry Williams

>Wiley,

I no doubt I can heat treat more accurately by eye than when using our computer controlled furnace. The changes one can see in the steel are dramatic. My problem lies in the size of steel I can uniformly heat outside the furnace. For something like a bench plane iron, I will get more dependable results with the furnace.

I'm becoming convinced there's more than just myth that the old smiths could hammer refine the steel and very effectively control grain size. I'm afraid that this art has been a casualty of "modern technology." I haven't seen any reference to this in contemporary black smithing literature but it's in the old books.

Re: John Henry versus the steam hammer

#4

Re: John Henry versus the steam hammer

Warren in Lancaster, PA

>About a dozen years ago, a Williamsburg blacksmith showed me a plane iron they had made. It was thin like many 18th century irons (the one I have is 1/8 at the thick end) and I asked him why they were so thin. He thought that 18th century woodworkers were able to handle a more delicate tool and that the thick irons of the 19th century reflected a waning of craftsmanship.

Two years ago I had a job carving white oak for 9 weeks straight. I was particularly pleased about how well my Henry Taylor tools performed and that my body held out for the job. Imagine my surprise a few months later when someone on this forum suggested that nobody used HT tools any more because they have weak steel, bend and fold, and don't hold up. Just last week a fellow told me that he had been carving white oak and his tools (did not ask the brand) got all ragged and beat up.

I think it is hard to evaluate the performance of these tools without respect to the user's techniques, both sharpening and using. A smooth and deft technique is easier on the tool than a clumsy one. The needs of an 18th century cabinetmaker or joiner were different than that of a hobbyist today, and I think that is reflected in the steels.

Re: John Henry versus the steam hammer

#5

I am a market of one

Adam Cherubini

>My opinion is that we have abdicated the requirements for edge tools to the manufacturers. They now define the requirement via their inspection/QA criteria, then publish that as marketing. The WW mags then test that criteria to see if they live up to it. It's a little like leaving the fox in charge of the hen house, except that in this case, the fox is sincerely trying to respond to his customers. Does that make us hens? Okay so I mixed up my metaphors there somehow.

Anyway, I want off the metallurgical merry go round. I want chisels that make sense for the work I do, are sized and shaped for an expert user, and don't require unobtainium to hone. Without anything on the market that compares to the full set of W. Butchers currently in my toolchest, I decided to make my own.

Hand forging does indeed give me some flexibility. One of the ways I used this flexibility was to heat treat different sized chisels differently based on their different usage. Wider chisels can be softer, which makes them significantly easier to hone. And I do prefer, though I can't measure, the finer grained steels. I've used several of the tricks in my magic (bass) bag to get there.

I'll probably offer these in comprehensive sets in the very near future. You can expect ridiculous prices. But i think these chisels really do add something new to the market that hasn't been offered in the past 150 years.

Adam

Wiley, I'd like you to test one of these when you get your $5000 microscope. I should probably send you a butcher as well or an old cam.


img

Re: John Henry versus the steam hammer

#6

want a better chisel, buy better steel

Bill Tindall, E.TN

>This smith, if there still is one, is limited to vanilla carbon steel that can be forged. In spite of the control postulated he/she is limited by the inherent properties of the alloy at hand. Why would one want to believe that carbon steel of 1850 would be the best alloy for making a chisel ever discovered?

Another route to better chisels would be to buy a better steel alloy suitable for this task and heat treat optimally for the task. I know that the better alloy will win over better heat treatment of carbon steel. This has been the case with knives and it is the case with chisels and plane irons.

Someone, maybe everyone, dismissed CPM 3V as a chisel steel when we first proposed it on Badger Pond years ago. We initially chose 3V as a chisel steel. It was an after thought that we made good performing lathe tools and plane irons from it. Well, at long last I found locally a Swan and bought it just to see how much better it was than anything else I owned. It held up better than Sorby, doesn't everything, but it was about the same as Two Cherries and not close to the 3V chisels we made. It does abrade easily but this is not a factor in my sharpening regimen.

Chisel steel is easy to spec out. Unlike plane irons where wear is a factor, hardness and toughness are the only factors of importance for chisels, presuming one has gravitated to the nirvana of diamond sharpening so that abrasion resistance is not a limitation. You want the hardest toughest steel man has discovered. That said, one goes to a table of steel properties or better yet the tech service department of a high performance steel alloy vendor and asks what is best, price no object. Another component is to then have the stuff heat treated at a reputable factory where they hit the target every time and the stuff comes back flat.

This approach lacks the glamor of shade trees and forges or oriental mumbo jumbo so I appreciate it isn't for everyone. But if the goal is simply the best chisel on the planet, buy the best alloy for the task and get it reliably heat treated. If you can bury a 25 degree mortise chisel in oak with a dead blow hammer and pry out chips without fear I will take notice of forged carbon steel. I can't recall when I last sharpened my 3V chisels but it has been at least once since I made them.

Re: John Henry versus the steam hammer

#7

Re: want a better chisel, buy better steel

Bob Demers

>Interesting debate we have going on there, look like you have openned a Pandora box, Wiley :-)

From, state of the art CPM 3V, to mumbo jumbo dirt floor hand forging using old 1850 iron layering steel, referencing old standby Swan (I have and love their chisels) and etc...

This as all the hallmark of yet another classic debate on a popular WW related subject.

What I got so far is that what makes the best chisel or plane iron to each and everyone of us, is a very personal and subjective thing.

Not all of us valued the same qualities in our cutting edges.

I for one prefer spending elbow grease time honing my edges to a mirror finish in good old CS, although i'll spend more time maintaining them than on my O2 steel blades, I prefer the edge I get on them, and the way it feel and performs in my hands. A very subjective thing, and no doubt bias by my love affair with old rusty relics but notheless, that's what I prefer. Besides, I find O2 harduous to sharpen by hand, so I think we can forget CPM 3V in my future!!

I know, I know, I could always embraced another sharpening method, but im quite happy with my results, so why change?? Stick to whatever work for you.

In the end what matter most to me is the feedback i'm getting from the interaction of the cutting edge on the wood fibers: the sound a sharp blade makes, the resistance encountered, the flex (as opposed to the snap, Oooops) etc. Thats the beauty of woodcarving, one forget everything else but concentrate solely on the cutting edge bury in the wood, its location, your hands position, and the results...

Try that with a power tool, Ah!

Beyond the pure science, I suspect that the intimate knowledge of the smith with his material has an effect on the final product, one that technology could not quite reproduced.

Bob, the galoot

Re: John Henry versus the steam hammer

#8

Effects of forging on carbon steel

wilbur

>I found this article written by Sherby and Wadsworth, out of Stanford University and Livermore National Laboratory, on "ultrahigh carbon steels". This is defined as steel that has a carbon content of 1.0-2.1%, which is the range that includes the carbon steels used in Japanese chisels and plane blades. I'm assuming that this would also include the hard steel layer found in older western chisels as well (Stephen?). There is some good information here on how mechanical processing (i.e. forging, although rolling steel is also included) can affect the formation and size of the carbides and the overall properties of the steel.

Here's a salient excerpt:

"By breaking up the continuous iron carbide network at high temperature, it would result in a more forgiving, i.e. more ductile, material. And, contrary to popular belief, we knew that iron carbide is not brittle at intermediate and high temperatures. A network-free material was developed by continuously mechanically working the UHCSS (1.3%, 1.6%, and 1.9% C) as they were cooled from a white hot temperature (1200�C). This mechanical working (by either rolling or forging) broke up the iron carbide networks as they were first forming during cooling, i.e. at a point at which they were still thin and not fully continuous. In this way, the iron carbide that formed upon cooling never had a chance to grow and create the thick networks normally associated with ultrahigh carbon steels. Examples of the fine microstructures developed in a 1.5% C steel, taken by high magnification transmission electron microscopy, are shown in Fig. 4. The light-colored grains are iron and are sub-micron size, and the dark particles are iron carbide. This material is superplastic at high temperature and, of equal importance, is strong and ductile at room temperature."

The article goes on to show that ultrahigh carbon steel can be made to have very fine grain, while remaining very hard, ductile, and strong simultaneously. In fact, later on in the article the authors write, "Clearly, ultra-fine-martensitic UHCS would be exceptionally suitable in wear resistant applications such as drill bits, industrial knives, and hand tools." (Emphasis added.)

Now, this is not to say that heat treating or cryogenic processing couldn't further affect the size or properties of the carbide particles, or that powdered metal technology couldn't give the same result, but it certainly shows a significant role for forging in the development of the properties of carbon steel, and that some very impressive results from high carbon steel can be attributed to the forging process.

Disclaimer: metallurgy is way out of my usual area of expertise, so if there is a different interpretation of what I'm reading in this paper, I'm all ears.

Re: John Henry versus the steam hammer

#9

Re: want a better chisel, buy better steel

ThomD

>We have the advantage of both the latest scientific methods, and whatever remains known or seems to have been rediscovered in the old world. On the slightly scientific front, stuff like FWW laboratory tests etc... still mostly come out with hand made and forged chisels on top. Over 30 years I have never seen a chisel test on performance that was won by anything other than a Japanese blade. Rarely are the testers even particularly competent woodworkers, they still couldn't avoid the glaringly obvious. I would point out that in some cases the wining chisel was a hand made better quality item, and in some cases the winner, or second place was taken by a lower quality Japanese chisel quite possibly made largely by mechanized processes and industrial heat treating methods.

The white and blue paper steels are basically tool steels in paper protective wrappers like O1 is sold in. In some cases, even better tools are made out of home made steels. Again what is winning out is the craftsmanship not a specific method of doing things. I have yet to see anything out there that compares to Japanese hand tools, it's the people behind the product, not some artificial criterion like hand forged or not.

An important part of the craftsmanship is the craftsmanship of the target market craftsman, as well as the maker. Japan has remnants of the original crafts of both toolmaking and woodworking, that remain intact. This raises the standard of play. In 30 years there has been a huge improvement in the quality of tools people are making here. If one looks at texts form the 70s, they were full of info on how to scab together a decent kit of tools. By and large the hobby woodworker was at a fairly low level even ten years ago. In the same 30 years the clients of the average Japanese tool maker would have been everything from existing living treasures, to folks who on day one of their apprenticeships were in a more enriching environment than the luckiest of us is in for more than a few days at a time. Of course their tools are better, but it isn't really whether the smith is hitting it with a hand held hammer or a power hammer that counts, for the most part.

There are a few myths in the thread so far:

"Now up front let it be said that there isn't much true handforging of individual blades going on. Anywhere. How could there be? The smith has to make a living unless he was born into money, and if he was born into money, he wouldn't be a smith. So, like John Henry, smithing has by and large lost out to machine methods. Cause how many smiths can get $200 a piece for their blades?"

Not if one is talking about filling Wal-Mart's shelves. There are thousands of very active smiths of very good skill level out there these days, and I can't think of a time when the realities of the craft have been as striped bare for all to see as they are today. Most of the action is in knife making where you can get 100 bucks an inch or a lot more. Still most are amateurs to some extent.

" 'Better' meaning that for comparable toughness and sharpenability, the smithed chisel will hold its edge better."

I don't see much evidence of this. Normally smiths have to also work in other criterion like durability in combat to make a case for a forging. However where it can mater is in the closeness with which a smith can work materials. Once it becomes a mass produced need and a mass produced solution, we don't need hand work anymore. I get frustrated when folks like us, nominally hand craftsmen, don't understand how a craft works. You want a plastic cafeteria chair, I can't beat a factory price. There are certain kinds of needs a charimaker alone can meet. Same deal with tools. Forging can be a very efficient way to work materials though. Rougly I would compare it to busting out wood, nothing is faster than spliting a log, riving, etc... Same thing with moving around metal. Plane blades are an easy one to make out of flat stock, but some other pieces are clearly easier to forge.

"Why do I think it is likely that the top smiths can beat professional heat treating? The reason is that the smith is guided by phase changes he can see occurring in the steel, as they happen, whereas the professional heat treater has the steel on a program which is established by the clock and by thermostats (if this isn't so, someone please correct me). F'rinstance, the smith can see the hot steel shrink slightly and change color in the orange zone as it transforms into austenite with a different crystal lattice. By responding real-time to phase changes in the steel, the smith is can shrink grain size, use higher carbon concentrations (think 'more carbides'), and manage his carbide distribution so as to optimize edge holding, toughness, and sharpenability of the steel forging."

I would tend to put this down in the myth department myself. Some of the stuff good smiths know how to do is process related where going along a particular path allows them to get somewhere a good heat treating cycle gets to automatically. I have recipees for heat treating that basically get you your hardness despite the fact it is hard to do the soak properly in an open flame. Where the smith does great work is by being close to the requirement and being relentless in testing to ensure he is getting the particular results he wants. I enjoy reading Ed Fowler's stuff because as a western rancher he has a real idea of what he personally wants in a knife, and he has been unterly relentless in getting it, and taking it to new levels. Though his objective is somewhat personal. His quest is similar to what John Alexander has tried to do with fitted wooden seating in ladder rungs.

"Any opinions or evidence one way or the other on smithing vs. professional heat treating?"

Toolmaking smiths are professional heat treaters!!

"hammer refine the steel and very effectively control grain size"

If we are in the area of "packing" here that appears to be contrary to what science tells us about steel, and many/most smiths don't seem to feel the need to cling to that. There are things smiths can do to reduce grain size through heat treating, and other choices.

"I think it is hard to evaluate the performance of these tools without respect to the user's techniques, both sharpening and using. A smooth and deft technique is easier on the tool than a clumsy one. The needs of an 18th century cabinetmaker or joiner were different than that of a hobbyist today, and I think that is reflected in the steels."

+10, I would just add that wood has quite a bit to do with it also. There is a correlation between the tools and the wood available in quality and species at a given time.

"Why would one want to believe that carbon steel of 1850 would be the best alloy for making a chisel ever discovered?"

I'm with you on that to an extent, but:

- Steels aren't always discovered, they may well be crafted for the intended use, then it becomes easier to believe they are better, when handled by experts, than something we may have today.

- So much modern stuff is crap, and may explain why the cross slide on a 100 year old lathe doesn't snap in half like it's replacement today. I'm starting to worry where our structural steel is coming from. I don't think 19th century gun barrel steel is better than the modern stuff, we care about guns. If you can find me a modern steel that is designed for making chisels alone on a similar scale to the ones we press into service...

"I know that the better alloy will win over better heat treatment of carbon steel."

That isn't always the case today. Lots of knives remain made in simple carbon steels, are better regarded as such, and that is even with the popularity of stainless to contend with. There are some non-performance reasons for this, but performance is also a part of it.

"This has been the case with knives and it is the case with chisels and plane irons."

Not universally so. There are a lot of serious users out there who don't agree. No way you are flogging the alphabet soup to the Japanese classically trained guys. Adam, crushingly, wants softer steel! These are common responses in the knife biz also.

"If you can bury a 25 degree mortise chisel in oak with a dead blow hammer and pry out chips without fear"

Then you're obviously a newbie (speaking of the person in the image)

"Chisel steel is easy to spec out... comes back flat."

You would have to admit though that this approach is glaringly obvious. To some extent this kind of approach works for wood turning... Just isn't working for me on the other wall of the office. I would tend to agree that there has to be a use for even "better" steels, it just doesn't seem to be all that important.

An example of a different sort is bicycles. Bikes made of chromo tubing remain popular, even in forms that would scandalize a traditionalist. Super materials like carbon should have taken over long ago, but they can't and probably won't for many reasons. Similar issue in golf club shafts. Sometimes the obvious answer is just wrong. However Carbon has been dominant in sports like fishing for decades. In archery where both bows and arrows seem obvious candidates for carbon, it is used most widely only on the harder to make and more easily broken arrows. The world is a complicated place.

"This approach lacks the glamor of shade trees and forges or oriental mumbo jumbo so I appreciate it isn't for everyone."

These kinds of comments tend to devalue input, and open up to dismissal for reasons that I imagine would be as unfair as they would be unflattering. Talking about oriental mumbo jumbo would probably strike them as rich when we are far more prone to idle talk than they are.

There are certainly Japanese tools that are made for the tourist trade as I like to call it, but there are also a large range of very impressive, "real" tools. I really have difficulty understanding how anyone who is a serious craftsperson could fail to see it. It is a long way from saying that to saying everyone should use them. I have a lot of Japanese tools, but I don't really know if they have advanced my personal cause that much. They almost become an end in themselves. But that is wholly different than saying they aren't good tools, or worse. At the end of the day, I want to make things that excel in function and beauty, and I can see it when others achieve that end.

"He thought that 18th century woodworkers were able to handle a more delicate tool and that the thick irons of the 19th century reflected a waning of craftsmanship"

I don't know about that, though I have often felt the same way about infill planes...

Re: John Henry versus the steam hammer

#10

Different versions of tools

Pam Niedermayer, Austin, TX

>Warren, it could also be that tools from a given manufacturer vary from time to time; so perhaps your HT chisels are very old, and the new ones aren't nearly so good.

Pam

Re: John Henry versus the steam hammer

#11

Re: want a better chisel, buy better steel

Warren in Lancaster, PA

>"hardness and toughness are the only factors of importance for chisels"? I don't know who agrees with this notion. I cannot imagine a long time worker thinking something like this. To me the qualities I like in a chisel are hard to describe and hard to define, let alone quantify.

Imagine a guy setting himself up as a violin appraiser and proclaiming there are only two qualities that matter. Both easily quantifiable, of course. "Buy our machine and become an instant appraiser!" This kind of talk would be quickly dismissed by someone who could actually play the violin.

Re: John Henry versus the steam hammer

#12

Re: Different versions of tools

Warren in Lancaster, PA

>Yes, Pam, I agree this happens. I do have some HT carving tools bought in 1977 and some bought in April of this year. But what I am suggesting is that different people, with different skills and different habits, will have different reactions to the same tool. I think you would agree with this.

Re: John Henry versus the steam hammer

#13

3V tools

Pam Niedermayer, Austin, TX

>Bill, IIRC you don't forge tools made from 3v, instead you buy appropriate thicknesses and hacksaw/grind to appropriate shapes, then send them out for heat treating. If this is correct, do you grind the bevels before heat treating?

Pam

Re: John Henry versus the steam hammer

#14

Re: Different versions of tools

Pam Niedermayer, Austin, TX

>Certainly I agree, thought it intuitively obvious. :) BTW, I tend to be a reductionist, so when I respond, typically I agree with everything said by all except the particular items addressed in my response.

Pam

Re: John Henry versus the steam hammer

#15

Re: want a better chisel, buy better steel

Pam Niedermayer, Austin, TX

> Imagine a guy setting himself up as a violin appraiser and proclaiming there are only two qualities that matter. Both easily quantifiable, of course. "Buy our machine and become an instant appraiser!" This kind of talk would be quickly dismissed by someone who could actually play the violin.

This is why I only consult Consumers' Report for those items for which I'm a general, amateur consumer, say washing machines. For anything I know about, say cameras or computers, they give very bad advice. I do this knowing I probably should learn more about anything I buy, but there are limits.

Pam

Re: John Henry versus the steam hammer

#16

Nice summary, Thom.

Pam Niedermayer, Austin, TX

>

Re: John Henry versus the steam hammer

#17

tool making process

Bill Tindall, E.TN

>Tool is rough shaped including bevel while it is soft and easy to grind and saw. Because heat treating alters the outer few thousandths of an inch I only rough out the bevel and refine it after heat treating.

Re: John Henry versus the steam hammer

#18

I remain waiting to be convinced

Bill Tindall, E.TN

>It seems the application of these hand forged products is for things like swords and knives, items where the aura of the process of fabricating the item can become more important to its owner than the item's performance.

I have great faith in the ability of business to find and utilize superior technology. If someone can show me that this steel is being used in the Phoenix mars lander or some such industrial application demanding the highest performance materials I will concede that indeed there isn't a better modern alternative alloy. But if the only market for this steel is in products where the story of how it is made becomes the main selling point, then I remain skeptical that there isn't a modern steel with equivalent performance.

The argument that these hand forged steels are too expensive for industrial application won't hold water. If the performance is there this hand forging would be done in 3rd world countries. In fact it would seem to be an ideal industry for such countries if there was a market.

Keep in mind here that the discussion is not whether hand forged carbon steel is better than generic carbon steel; I agree it may not be. Rather, can the performance of hand forged carbon steel be matched or exceeded by modern alloys which seem to have displaced these hand forged materials in all but some specialized consumer markets.

Re: John Henry versus the steam hammer

#19

Re: want a better chisel, buy better steel

Adam Cherubini

>I like the whole idea of CPM. I guess what I don't like about it is that you need to hone it with diamonds, it's expensive, and difficult to form. I think if someone were casting CPM chisels in shapes I like, I would buy them. And that's never going to happen until folks demand chisels like that. So you're the market of one too. But I think that's what it takes, Bill. And that's why, like you, I'm making chisels at the moment.

So let me be clear:

1) I have a whole long laundry list of what I want in a chisel. Edge holding is one item on that list and it's not the first item.

2) If it wasn't for Bill Tindall, I don't think many people on this list would know what CPM-3V is. There's no question in my mind that future woodworkers will be using it more and more. I can't help wonder if that would be true if Bill Tindall was killed by a bus 5 years ago.

Adam

Re: John Henry versus the steam hammer

#20

Re: I am a market of one

Andrew Lunn

>Hey Adam, what are the chisels in your photo, one old one and then one new one you forged yourself? Or two old ones? Do you laminate your blades, and do you create bolsters? If so, how do you form your bolster? I had an interesting conversation with one of the smiths at Williamsburg about how they do their bolsters. I'm also into blacksmithing, but more into carving tools than chisels.

Re: John Henry versus the steam hammer

#21

Thanks.

Pam Niedermayer, Austin, TX

>

Re: John Henry versus the steam hammer

#22

Killed by a bus?!

Pam Niedermayer, Austin, TX

>How about a simple "were he not doing woodworking?"

Pam

Re: John Henry versus the steam hammer

#23

Re: I am a market of one

Dean J in MN

>I'm with Adam and Warren on the chisel issue. There seems to be a focus on the metal, rather than the chisel. I've all but abandoned my LN's due to the A2 steel. IMO A2 was a huge mistake for a chisel.

I've been using #1 sweep single bevel carving chisels for a while now as my daily chisels, rehandled them with my favorite handle. They come close to what I am looking for in a tool. I still wish they were thinner. Looking at the chisels at Wmsbrg or the ones listed from the Seaton chest and one thing sticks out -- thin. Warren mentioned a tool fit for the craftsman using it. I grant you, a thin chisel in the wrong hands may result in bent/broken chisels. But, I will trade "strength" for ease of use.

So, specing steel for a chisel may be easy, but forming that tool to be useful is more difficult. As we can see, there are those of us who can not find one in the current market.

-Dean

Re: John Henry versus the steam hammer

#24

Re: I am a market of one, make that two...

Pam Niedermayer, Austin, TX

>And that's partly why I love the Tasai ultra thin paring chisels.

Pam

Re: John Henry versus the steam hammer

#25

2 new chisels

Adam Cherubini

>