Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Working with leather Qs

Posts

Re: Working with leather Qs

#26

Re: Working with leather Qs

Skip in Falls Church

>Hi Alan,

I hope I can add a couple of things that might be helpful. If you have a drill press you can save yourself a really sore palm. I took a crappy old plastic handled Phillips screwdriver, ground an awl point on it then broke the handle off. That can be chucked in the drill press and will make the process of punching holes much easier and neater.

Use wax on all your punching and sewing tools - bees wax is sort of traditional. It really does make the process much easier. You might also want to make a fid. A fid has a blunter point than an awl and is used to open up holes that didn't get punched well or that close up. It's better than trying to use an awl after the hole is pumched because it will only follow the hole that is there and not punch through in a different place as can happen with an awl. You can make a passable fid by putting a short awl point on an old screwdriver then blunting the point.

Rotary cutters (a round blade on a handle) works really well for cutting leather if it's not too thick. You're really limited to something less than half the diameter of the cutter because of the was the round blade is mounted. You can find them in the sewing section of any craft store and the replacable blades are fairly inexpensive are really sharp.

While saws don't work well for cutting leather, a belt sander works well for cleaning up edges if you need to.

Skip

Re: Working with leather Qs

#27

Re: Working with leather Qs *LINK*

BobStrawn

>Another leather for a tool holder possibility would be ballistol. I have never used it, but in side by side comparisons, ballistol tends to come out as the best metal preservative more often than not. There are those who consider it an ideal treatment for leather, wood, cats, people, and even guns.

Bob


Portmanteaus

Re: Working with leather Qs

#28

Re: One would think...

Stephen Shepherd in the State of Deseret

>Bob,

You Wrote:

'Pure neatsfoot oil is great stuff, but most of the stuff labeled as pure neatsfoot oil is not. Neatsfoot oil is not advised for conservation, since it will eventually harden.'

100% Pure neatsfoot oil is readily available at some espense. Many compounds and adulterated neatsfoot oil products are on the market, avoid them.

What documentation do you have that it will eventually harden, it is a fixed oil so I do not think it polymerizes?

Stephen

Re: Working with leather Qs

#29

Re: Working with leather Qs

Alan DuBoff

>Skip,

Thanks for the response, I was able to glean some things out of it. I do have a drill press, although I was thinking of using a Miller Falls #2A eggbeater, I have used it to drill holes in belts...

I have seen those circular cutters at a local fabric store, I just bought my daughter a pair of Gingher shears, which are some of the nicer shears, and while I was there I did see some of those rotary cutters. I will check those out, but I also have some exacto blades with a curved front that I used to use for trimming ping-pong paddle rubber, but the rotary blade could be more accurate.

I like the drill press idea, and I do have some bees wax, I use it on my handsaws as well.

Re: Working with leather Qs

#30

Re: One would think...

Alan DuBoff

>Stephen wrote:

"What documentation do you have that it will eventually harden, it is a fixed oil so I do not think it polymerizes?"

When I was at Tandy today, I asked about that, and the gent who was the most knowledgeable said he has never heard of that either. He mentioned that Bianchi dips their entire holsters in neatsfoot oil, and let's them drip dry. I must admit their holsters do have a nice look to them.

However, I decided to get the Fiebings white saddle soap, all of the folks there seemed to like it as their first choice, but none had anything bad to say about neatsfoot, and commented that it has been the conditioner of choice since the dirt age.

However, I do have some Lexol leather conditioner, that is the recommended choice of leather conditioner for English leather seats in both Rolls Royce and Land Rovers. I have an old '88 Range Rover Classic. I have cleaner also, but I think most of the leather I have is pretty clean...;-) They all highly recommended it also. They gave me 50% off on the Saddle Soap as it was on sale this month, so that only cost me $4.25. I think I have some neatsfoot oil actually, which I bought a few years ago for my Son's baseball mitt. I'm set on leather conditioners...:-/

Re: Working with leather Qs

#31

Progress update...no sheaths yet though...

Alan DuBoff

>Ok, this was a very useful thread for me. ThomD, Robin, Skip, DavidB, and certainly Todd, as I did learn a bunch from his post.

I did read the other thread that was pointed to about leather on WC, and noted Todd's comments on dye, punching, welt (I will use that on both knives and saws), burnishing, and most importantly the pics...what can I say, sometimes a picture is worth a thousand words...

Ok, so the guy at Tandy was very helpful, and funny the owners had made a saw sheath that was hanging on the wall, with the lousiest saw you have ever seen, a modern Stanley square handle with ugly pruning looking teeth...was the size of a backsaw with no back. It was in this Indian style sheath with carving on it and lace around the edges, it was way more than the saw deserved...I found out who the owners were when I asked who made that nice sheath for that lousy saw...:-/

Tandy sells a "Hand Stitching Kit" with Craftool tools, and the Al Stohlman stitching book, comes with the book, a Craftool 4-in-1 Awl (exchangeable blades), a size 6 Overstitcher, Adjustable Groover, 25 yards of waxed thread, 10 needles, and a dab of bees wax. I normally don't like to buy "kits", but this $59.95 kit was on sale this month for $34.95, and the book was about $15 alone I think. The 4-in-1 sells for about $30, and $12 for the groover, $12 for overstitcher, $8 for the thread, $3 for needles, so that seemed like a pretty good deal for $35 while it's on sale! *g*

In addition, I got another book once they showed it to me, Volume 1 of "The Art of Making Leather Cases" by Al Stohlman, this is a fabulous book that shows how to make all types of different shaped tool and knife sheats, pouches, bags, etc...but most importantly the "Flash Cube Case" for those square flash bulbs on the old cameras I remember as a kid...even a film cartridge case for an Instamatic Camera film cartridges...I had one of those as a kid!!!! Seriously this is a very useful book to show how to cut various shapes and how to stitch them. Along with the other stitching book which shows the various stitches, I have the information to solve many sheath and case problems for various tools.

I also got a small container of an all-in-one dye which was recommended until I can learn more about dyes, but this will do stain and finish in one, along with edging. The white saddle soap, and some brown thread to match the dye.

I like that overstitcher, very nice to mark out the stitching, I just ran it across a piece of leather and I like it! That will make it look neater than if I did it by hand.

The stitching book linked to by David Barnett and mentioned by others, does in fact answer many questions, how to hold the needle, awl, the various stitches, etc...yes, that is spot on, and the other Al Stohlman book on cases is spot on for what I'm doing.

And lastly, it has been pretty cold in Cali for the past few weeks, and we've been getting pelted with rain, but today when I was headed up Highway 280 through Portola Valley along the outskirts of Silicon Valley, it was gorgeous...I hate to tell folks back east, but it was a beautiful day in Cali...on to work after, and a South Bay Metalworker's meeting in the eve...(although I missed the hand tool chat:-(...maybe I'll be able to catch it next week)...knew very little about leather last night, got a bunch of info, was able to get what I need, and a beautiful day on top of it. I even let some old ladies cross the street with walkers in San Mateo, and they smiled and waved at me...this is a great place on a day like today! *grin*

Re: Working with leather Qs

#32

Re: Working with leather Qs

Alan DuBoff

>Bob,

I have done a bit of googlin' on Ballistol and it's interesting, to say the least. Is there anything that it doesn't do? :-/

From the sounds of it, you could cure world hunger with it.

Would like to hear from someone that has used it. It seems to have such a wide variety of uses. It looks like it's been around for about 130+ years, but I've never heard of it before.

I have some Lexol leather conditioner also, which seems to be highly recommended for leather. I had it for the leather seats in my Range Rover, the English seats are very distinctive and Lexol is the recommended conditioner for both Rolls Royce and Land Rover, FWIW. I can honestly say that their recommendation to use Lexol has worked out much better for me than the Lucas electronics they put in English cars...*gd&r*

I did get a couple pieces cut for a small sheath, but had to change my design as the leather is so thick. I tested a small patch with dye to see how the color looks, also.

Re: Working with leather Qs

#33

Those Portmanteaus Bags look nice

Alan DuBoff

>Bob,

Those bags really look nice, I can't help but think they would make an excellent tool bag, with a few compartments to separate a couple joinery saws, a chisel roll, marking tools, shave, block plane, etc...

I currently use a DeWalt bag, my kids gave it to me, and it's pretty strong...I was looking at the amount of stitching and scratching my head, actually I was trying to scratch my head but it was spinning.;-) I am having better luck with a Miller Falls egg beater to drill the holes first it seems, but I need to use a smaller bit that what I have been practicing with. Used the speedy stitcher some tonight also, I understand the concern for failure of the lock stitch, but it seems pretty strong, IMO.

Tandy had some fairly large shoulders or double shoulders for about $80-$100, they would be big enough to do a nice bag like that. It would be possible to make a small bag out of some of the bellies they had, about 8oz, they were on sale at my local store for $2.99 sq.ft, or about $15/each. I saw some really nice looking upholstery leather, in a very antique looking stain, it was gorgeous...leather could become a jones worse than wood...*yikes*

Re: Working with leather Qs

#34

Re: One would think...

BobStrawn

>One my conservator sources advised that neatsfoot oil hardened eventually. I am not sure, but if memory serves it was a naval archeology preservation recomendation list that may still be locatable somewhere on the TAMU website.

I just googled it and found such a reference in Wikipedia, so it must be absolutely true. :) http://en.wikipedia.org/wiki/Neatsfoot_oil#_ref-3

The reference that the wiki mentioned was "Neatsfoot oil, like other leather dressings, should not be used on important historical objects, as it will oxidize with time, and embrittle the leather even more.[4] It also may leave an oily residue that can attract dust." The reference is, Canadian Conservation Institute, Note 8/2: Care of Alum, Vegetable and Mineral Tanned Leather.

I also found this http://palimpsest.stanford.edu/byform/mailing-lists/cdl/1996/0875.html

it seems to defend and defame neatsfoot oil.

I would suspect that processing, adulterants, and even source breed or breed diet could give a wide range of behavior to neatsfoot oil.

As far as the science goes, neatsfoot oil has an iodine value of 75 to 85. Drying oils have values above, 130, Non drying oils are below 115. The non drying portion of oil will have a tendency over time, to leech out or pass to other materials or even evaporate. The drying portions, while not useful as drying will still tend to oxidize and become more solid.

In my own personal experience, neatsfoot oil is the best material for waterproofing leather. I would argue that if waterproofing is an issue, then conservation is probably not. I do think that the best materials suitable for protecting materials kept within a close range of temperature, and behind glass, are not always going to be the best materials for protecting tools that we use.

In use, leather is likely to contact sweat, condensation, and weather.

I just found the TAMU data, and cannot find a reference to neatsfoot oil, so who knows where I get my notions from. ;) It is however a very nice site with some great data and formula for restoration and conservation. http://nautarch.tamu.edu/class/anth605/File7.htm

Bob

Re: Working with leather Qs

#35

Re: One would think...

Stephen Shepherd in the State of Deseret

>I have no doubt that it evaporates and mechanically wears off of leather, but I do not think that it actually forms a film.

I have read the CCI stuff and what AIC has to say and what curators and conservators say but there are also other opinions within the profession.

I make a Leather Reviver that contains neatsfoot oil, turpentine, linseed oil, lanolin and glycerine. It works well to consolidate and stabilize old leather especially red rot. It does darken and will harden but remain flexible (BLO and glycerine). The neatsfoot oil and lanolin condition the old leather.

Stephen

Re: Working with leather Qs

#36

Re: Those Portmanteaus Bags look nice

Skip in Falls Church

>Hi Alan,

Bellies are good for beginners because they are relatively cheap and you can get a variety of weights to see how they work without breaking the bank. From my experience 4 oz is thin enough to shape easily if you want mold it but is a bit thin for good carving definition. 8 oz is thick enough to get good carving definition but is a bit harder to mold. Bellies lets you try things out without making a big investment. However, bellies tend to be a bit less consistent in weight than shoulders - especially around the edges. Just like with wood, the weight you use will likely depend on the purpose and your preference.

You should realize that sliding down two different slopes at one time can be interesting. :)

Skip

Re: Working with leather Qs

#37

Re: Those Portmanteaus Bags look nice

Alan DuBoff

>Skip,

I'm finding out that the 16oz is tough to work with, and I am just soaking my first piece...that makes so much difference, it starts molding after a while...or at least starting to...the Stohlman book suggest leaving it in a plastic bag overnight.

I've tried a few things, and I have a piece that I currently made which has a welt around the entire blade, so a strip sandwiched in between the edge. I used Barge on that and will try to clean it up and stitch it tomorrow. Can I soak something that has been glued with Barge? I think that is waterproof also...

I have some other scraps I have been practicing to stitch and did some double stitches tonight. The Stohlman book was very helpful, and one thing I gleaned from it was to make copper rivets out of romax wire. That looks handy if one doesn't have rivets.

Yeah, I agree on that second slope, although woodworking tools are much more plentiful and expensive. I am seeing that there are inherently more and more tools to the leather slope though (not that I need them)...gouges, edgers, strippers, folders, awls, needles, not to mention the various leathers. Yes, I did note the inconsistency in the bellies, the edges were much thinner.

Like wood, it seems you need various thicknesses, like 6-7 oz for straps, 9-10 oz for small bags/pouches, etc...I need to experiment some to see what does/doesn't work.

Is it possible to manually split the leather without using a machine? I have seen machines, but I didn't know if it was possible to moisten it and split it by hand to get 2 x 8oz thicknesses. Can that be done? I guess you would only have one grain side on one piece and the other would have 2 sides of flesh. That would only yield one usable piece, although the double flesh would be preferred for welts. I glued a regular piece in between for the welt, so there's a grain side on one of the walls/case-side. But it seems one really needs various thickness leather for straps, tabs, loops, billets, etc...so that is very much like working wood, except that it seems we have more flexibility with wood in that we can dimension it. Leather is harder to thickness/split.

Re: Working with leather Qs

#38

Re: Those Portmanteaus Bags look nice *LINK*

BobStrawn

>I did rather like the portmateaus, heck I just like the name. I think it would make a rather fabulous tool tote. From making my own tool totes, I would strongly advise carefully putting the tools in a box about the size you are planning and feeling the weight. A well packed bag can weigh much more than will retain shape well or carry well.

Horse Butt and Pine makes a nice, relatively inexpensive tool tote and does not need a lot of leather working skill.

If you go to the site and click on the picture you will get all sorts of data on my personal favorite tool tote.

Bob


img

Tool Tote

Re: Working with leather Qs

#39

Re: Those Portmanteaus Bags look nice

Todd Hughes

>I have thinned down leather used for sheaths with a common wood body spoke shave, just shaved down the flesh side. worked good and i believe was a tradtional tool used by leather workers too. I have had two ebony spoke shaves made by Osborn a leather tool maker.

Copper boat or roofing nails make good rivets too....Todd

Re: Working with leather Qs

#40

A shave makes sense...

Alan DuBoff

>Todd,

That makes sense, I guess, just didn't realize it could be shaved like that. So, no reason any edge tools like chisels and gouges can't be used I guess, it is softer than wood.

I have seen a lot of Osborne stuff around, even used on ebay, and they had quite a few Osborne tools at Tandy also. The nicest knife they had was a small Al Stohlman that was $40, was some type of nicely grained rosewood or similar with a milled brass ferrule, and a small blade. It was a trimming knife. The rounding knive was more like $100, as I recall.

It was in fact a Osborne head/round knife that gave me the idea to make one out of the plow disc I have...I think that is the only piece of tool steel that is round which I have, so I figured it would be the least amount of work, to forge.

Can you use the shave on edges? I may try that to find out, and answer that for myself...:-/

I have a small sheath that I glued last night, it's 3 layers at the edge, 2 outer skins and the welt. Would be nice to put this in a vise and use a plane on the flat edge, so will try and see later as I don't have a vise out here, other than a saw vise. I was thinking if I dressed the edge and burnished, it might look ok, but first I want to dye it and stitch it. Maybe take the cobbler's hammer to it.

I have another I cut, and just folded it over, may put a thin welt in the edge when I stitch it. That was the one I soaked in water as you suggested...and it's uncanny how you can mold this stuff, bend it over, etc...

Good tip on the copper boat nails, that seems like it would be a bit thicker and work better than romax, but that depends on the gage wire. I don't have any rivets and was planning to use some type of copper.

Maybe I'll have a sheath pic to post soon, but not tonight and most likely not until the weekend, I've got things to do for work...Yeah, I know, sometimes people are surprised when they find out that I actually work.:-/ Trust me, I'd rather be playing around with wood and leather if I had my rathers. Some day I'll build a house, then I'll have a woodworking project to last the rest of my life...;-)

Re: Working with leather Qs

#41

That looks great!

Alan DuBoff

>I like the toolbox you built, very nice design, and I like how you used the leather inside to hold the tools. I can see lots of uses for leather in that regard, to hold tools inside toolboxes, on the wall possibly, or even to protect the edge with a piece of leather.

I didn't see anything on the Portmanteaus site, but will need to look. It sounds like they might actually make tool bags...I have thought of using leather inside of a toolbox before, but really hadn't thought about making the box out of leather itself.

Thanks for sharing, this is giving me some great ideas of how to incorporate leather with my woodworking, or for use with my woodworking tools. Say, did you make most of those tools in your box? They sure look like nice tools, I'd like to see some close-ups of them. Are those leather tools on the left side in the pic?

Re: Working with leather Qs

#42

Portmanteaus web site designed for cell phone??? *LINK*

Alan DuBoff

>Bob,

I have to say that their website is such a tease, like the following link states, "Photo of a Blacksmith Forged double buckle attached" and there's a picture. The picture is about the size of what I would normally want to be the thumbnail. Even the pictures they do have on their site, are very tiny, and they do beautiful work. Too bad...it is more than worth what they charge me to view them *g*, so I'm not complaining per se, just pointing out that the sites leaves me wondering if they designed it for people using cell phones or something...maybe one day someone will toss them a nickel so they can get a real computer...:-/

Can you see that forged blacksmith buckle? I know I'm getting old, but geez, give an old guy a break for crying out loud...*lol*

The other interesting thing to note is that they charge $45 to hand stitch that bag. How long do you think it would take to stitch a bag like that? I bet someone that knew what they were doing could stitch a bag like that in a couple hours. You'd think that a company would need to charge at least $45/hour for their labor, so $45 seems like a bargain, I bet they do that in about 10 minutes on a machine...*g*


Dual Chamber Small Portmanteau

Re: Working with leather Qs

#43

Re: Those Portmanteaus Bags look nice *LINK*

Skip in Falls Church

>Hi Alan,

If you start looking at vintage leather tools I think you'll find that they are at least in the same class as vintage wood tools. :)

I did a Wood Central article about making a holster for a block plane that you may find of interest. You'd be surpised at all the applications you can find for leather working to compliment your wood working.

Skip


Block plane holster

Re: Working with leather Qs

#44

Re: A shave makes sense...

Stephen Shepherd in the State of Deseret

>Osborne has been around for a long time, I have seen one of those half round head knives by Osborne dated 1836.

Alan, if you are going to make one of those knives that they are dangerous, especially if they have those swept back points on the ends, requires a good touch just to pick the tool up off the bench, let alone use it.

Salaman wrote another book 'Dictionary of Leatherworking Tools' much like his book on woodworking tools. Has directions for making cat gut, a good section on shoemaking and bookbinding.

Stephen

Re: Working with leather Qs

#45

Re: That looks great!

BobStrawn

>Thanks Alan, everything but the folding rule I made. Mostly from mesquite, osage and ash. Since tools don't take a lot of wood, I figure that making tools is a good self apprenticeship. An inexpensive way to improve you skills, before you spend a lot of money mangling wood. Along with the skills, you also end up with a nice collection of hand tools.

Bob

Re: Working with leather Qs

#46

I couldn't agree more, nice looking set of tools!

Alan DuBoff

>

Re: Working with leather Qs

#47

Re: A shave makes sense...

Alan DuBoff

>Stephen,

I am amazed that Osborne has been around that long, that is very amazing that a company has been existing and/or in business for so long!

Good point on the handling of the head knife, hadn't thought about that too much. I was thinking it would be good to roll along the blade as you cut, so that you could be applying pressure and progressing the cut.

Shoes are an intriguing project, I must admit, not too many DIYers making their own shoes, that I have run across...when I was a kid, there was a place that me and my hippy friends used to buy custom made moccasins, and they would trace your foot and make them by order. They are comfortable, but don't have good arch support. They used to put some type of rubber sole on them, which was glued. I think I still have them somewhere in the garage. I should try to dig them up and look closely at how they made them...(monkey see, monkey do).

Is there reprints of the Salaman book? ('Dictionary of Leatherworking Tools')

I'll have to dig around online.

Re: Working with leather Qs

#48

Fabulous article, and very useful stuff...

Alan DuBoff

>Skip,

I have always admired leather, and it is such a nice compliment to wood. I realized last night that both are organic materials, and both are living before we use them...fascinating to me.

Such a nice material for protecting tools, and especially any edge tool.

The wild boar looks nice, and I see that you used the block technique as shown in the Stohlman book, to form the leather around. Very nice case, these type of projects do inspire me.

One question I have in regard to leather. Is there ever any problem with mold on leather being stored for instance? Any precautions needed to ensure that mold or other damage doesn't happen? I guess as long as moisture is not present there shouldn't be a problem. But often different locales will be damp, and I wasn't sure if that could present a problem. There are so many different types of hides that I can see how a person could start acquiring various types to use on projects. Various thicknesses, tanning methods, colors/dyes, etc...

I guess the best advice is, "don't wear leather soled shoes near the slope", otherwise one will have a tendency to slide down faster!*grin*

Re: Working with leather Qs

#49

My first pair of ski boots were leather.

Pam Niedermayer - Austin, TX

>

Re: Working with leather Qs

#50

Re: A shave makes sense...

BobStrawn

>The shoe place you mentioned, may well be baldmountain.net.

Bob