Two words...
Bob Hackett(Mainely,Bob)
>Disc sander.
MB
Knowledge You Can Build On — Est. 1998
Two words...
Bob Hackett(Mainely,Bob)
>Disc sander.
MB
Got the perfect plane for that...
Dave Thompson - Champaign IL
>Eeeeeek, I hear the screech of finger nails on a chalk board....
This sounds like a perfect experiment for my possessed Stanley 12-204 anti-smoother. I never really got into making distressed faux antique furniture anyway.
Here's how I trued up my #62.
Derek Cohen (in Perth Australia)
>This #62 came to me quite pitted and the important side was a few degrees out of square.
Using sandpaper on a supported piece of flat glass plate, the plane is registered against a perfect 90 degree fence.
I clamped a board I use for cutting dados on my tablesaw against the tablesaw fence, then adjusted it with shims until it formed this perfect 90 degrees.
Apologies for the poor quality picture (taken from an old file).
With such a short piece of glass (my glass plate is now 1m long), it takes longer. The sandpaper here is held down with water only. This proved to be satisfactory, as the end result demonstrated.
Regards from Perth
Derek (presently in the early stages of building a low angle #51)
Nice work! I used angle plates and scraped...
David Barnett
>but the result is the same. Although I had a long granite angle plate to press up against, a surface plate (which so many seem to have, these days) with one of those imported iron angle plates would work, too, and not cost a small fortune. My Unifence is okay for ripping boards but I wouldn't trust it for sanding a long plane body (I can see light under a straight-edge in a couple places). I don't have an original #62 but I trued my L-N, a Bailey #5 and a #93 (yes, I'm another inexplicable fan of the #90-series, but not for shooting, of course). Totally worth doing on any plane used for shooting, in my opinion, but I used to love scraping iron during those long New England winters.
Re: I use something similar - a morso foot guillot
HC Sakman @ Victoria, BC
>Hi Andrew,
You sure got a good deal. That is a pretty serious contraption!
Chico...
Re: Nice work! I used angle plates and scraped...
paul womack
>Totally worth doing [squaring]on any plane used for shooting, in my opinion,
Well, I'm as keen (probably keener) on "perfecting" my tools as most, but if I had a plane for shooting that was causing trouble, I'd probably end up shimming (or planing!) my shooting board rather than doing that much work on the plane.
Of course, if you wish to use more than one plane for shooting, that idea doesn't work...
BugBear
Re: Nice work! I used angle plates and scraped...
Derek Cohen (in Perth Australia)
>Bub Bear
Now, would I ever use more than one plane for shooting? The very idea! :>)
Regards from Perth
Derek
Re: Here's how I trued up my #62.
Dave Thompson
>Wow Derek, that's a beautiful #62 you have. I think I might have enough gumption to polish scratches off a side, but I'm not sure I have enough to actually true it, unless it was pretty close to begin with. Nice work.
That's a pretty piece of wood you have that sitting on. What is it?
Re: I use something similar - a morso foot guillot
Andrew F in Australia
>Thanks Chico,
They're fast reproducable, accurate and powerful enough - as I said, framing shops use a manual guillotine (like this one), an air-powered guillotine and/or an accurate (Swiss-made) mitre chopsaw and an underpinner to do most of the framework.
Just repeating, if you can get one second-hand, these things are worth their weight in gold - far better than a Lion trimmer or variant at a similar(ish) price.
Cheers,
Andrew
Re: I use something similar - a morso foot guillot
Dan Donaldson
>For me, it would be very expensive because I would have to build a new shop to have room for it ;-)
Re: Here's how I trued up my #62. *LINK*
Derek Cohen (in Perth Australia)
>Thanks for the kind comments Dave. The side of the plane was very pitted, so I had nothing to lose. I did do an article on the restoration of this #62 a few years ago. Link below.
The wood is Jarrah. That picture was taken a few years ago. It is the top of a chest of drawers.
Regards from Perth
Re: I use something similar - a morso foot guillot
Andrew F in Australia
>Hi Dan,
The footprint of mine is fairly small - 18" by 18" - there's storage space under the wings and the thing is on castors so you can roll it out of the way. The wings are 4' or so long but have storage under them. On mine, the unit also collapses so that it's only two feet tall or so. Takes less than a minute to set up.
I keep it under the sliding table on the saw when the saw isn't in use.
Basically, it's almost invisible in the shop as far as footprint goes
Cheers,
Andrew
edit: combined length of both wings is 4'
Andrew F in Australia
>
Re: I use something similar - a morso foot guillot
Dan Donaldson
>See, you are assuming that there is a place to roll it TO ;-) I couldn't even get an 18" area cleared up if I still wanted to make anything.
Shop space
Andrew F in Australia
>Hi Dan,
I knew your tongue was firmly planted in your cheek.
I'm getting close to the same space - about time for another cleanout and rearrangement (either that or to build more room, and I know whch one's cheaper.) I've got a bandsaw coming in the next month, so there's going to be even less space.
Cheers,
Andrew
Very bad!
Dean Lapinel
>Reading posts like this and seeing photos of the LANGDON MITER is unhealthy. It looks so interesting that now I want one!
;-)
Dan Donaldson
>
Re: The (almost) ultimate shooting plane
paul womack
>A dim memory has been tickling me.
A little digging in the OLDTOOL archives confirmed.
http://nika.frontier.iarc.uaf.edu/~cswingle/archive/get.phtml?message_id=75365#message
(the pictures are long gone)
Steve Knight will happily make you a close-to-ultimate miter, with a large square body (like the LN #9), added mass if you want it, moderate length. Since the body is wooden, you could add a side handle, like an old panel gauge.
But it also has the all important (IMNSHO) thick, skewed blade.
The latter is only otherwise available if ya' pony up for an infill skewed miter plane, the price of which is "a little" more than Steve's.
He used to list this tool, but hasn't for a while. A quick email confirmed that he'll still make it, he just doesn't list it!!
BugBear
to skew or not to skew?
bill tindall
>Not being an expert in these matters, what is the benefit to a skew that compensates for what appears to be greater cost in making, as well as more annoyance sharpening and adjusting?
Re: SKEW!
paul womack
>what is the benefit to a skew
In a shooting board the benefits of skew occure primarily at the start and end of the cut.
(ramped boards provide some of the same benefits, BTW)
At the start of the cut, the blade engages gradually; this decreases the "bang", which could well cause the workpiece to move.
The real benefit is at the end of the cut. Since the blade exits the cut gradually, there is MUCH less tendancy for the far edge of the workpiece to split off. In the picture, note that as the chisel passes over the back-side of the workpiece, the fibres being cut are still recieving some support from the remaining workpiece to their left.
As a minor benefit, a skewed blade also has a slightly lower effetive cutting angle, which is beneficial on end grain, but cutting end grain is easy enough that this benefit, though real, is not often of great importance.
BugBear
Re: SKEW!
paul womack
>For those that don't like theoretical considerations, I will point out that the VAST majority of dedicated mitre tools have skewed blades:
All trimmers (e.g. Lion style)
Roger Mitre plane
Stanley #51/#52
And in the 1909 Preston catalogue they list a number of dedicated "shuteing" planes, all 22" long. This topped out with a 3" wide skewed blade model, with "plated" side and sole.
Those old boys were doing a lot of shooting back then.
BugBear
Re: SKEW!
Dave Thompson
>Hi Paul, I agree with all the reasons and benifits that you list for skew, (though maybe not the magnitude). I think Bill brings up a good point, regarding more annoyance sharpening and adjusting. I'm not sure about the cost to mass produce, but for a one time fabrication, there would be an increased time cost. I think it comes down to, how much impact those benefits have, and I would imagine that will come down to each individual.
Personally, my #140 is my least favorite plane to sharpen probably followed by my side rabbet planes, and I'm not quite sure how I'm going to sharpen my newly acquired trimmer.... wait, Miller Falls #1 spoke shave is far worse than any of the above, but that would be a digression....
In the two long threads over the past two month asking about favorite chute planes, I don't recall anyone mentioning a skew plane, and some like RJ Wheeling have spent a professional life time using non-ultimate shooters.
Ofcourse, if I could get my hands on a cheap 51/52, I'd probably jump on it. ;-)
Re: SKEW!
paul womack
>In the two long threads over the past two month asking about favorite chute planes, I don't recall anyone mentioning a skew plane
I suspect that's because they're rare and expensive :-)
Nobody said the ultimate was cheap...
Someone did mention a Morso, and a Rogers.
BugBear