Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Options to eliminate sanding?

Posts

Re: Options to eliminate sanding?

#51

good points, and more on mechanism

Bill Tindall, E.Tn.

In my limited experience I have learned to open wide the mouth for it mostly gets in the way of changing the shaving thickness to meet the planing need. I don't fine diddling with mouth setting worth the effort if the cap iron is properly set. Get it out of the way and leave it there.

I have studied extensive data from Kees on mouth setting and tear-out and have formed a hypothesis of how the mouth opening actually works when optimally set. The best tear-out mitigation with the tight mouth is when the opening is mall enough to squeeze the exiting shaving. The result will then be essentially the same as the result of a optimum set cap iron. The friction of the exiting shaving exerts through its stiffness the desirable downward force on the incipient shaving ahead of the blade tip.

An analysis of downward psi forces generated by the mouth area alone shows that they are piddly small and I suspect of no meaningful effect on the shaving lifting ahead of the blade tip.

Re: Options to eliminate sanding?

#52

Re: It is irrelevant here ..

Derek Cohen (in Perth, Australia)

I hope we remain friends but it is your (this) post that is "irrelevant here".

Bill, I consider that you are my friend, and sharer of many discussions over the years. I hope that I have not said anything that would appear a personal criticism. All I believe I have stated was that a discussion of BD vs BU was not in the interest of the OP, and that it was this that was irrelevant.

Regards from Perth

Derek

Re: Options to eliminate sanding?

#53

Why not?

Bill Tindall, E.Tn.

"Bill, I am not trying to convince you that the BU is better than a BD plane"

Why not? The questions I am asking should(I hope) be important to anyone making stuff. If this assumption is wrong I need to stop typing.

If there are data to show a BU #4 would serve me (or us, the mixed tool woodworkers making stuff) better, cheap as I am, I would be ordering one from LV forthwith. I'm into making stuff and willing to buy stuff that helps me. My situation is no different than anyone else facing these decisions.....I think.

Re: Options to eliminate sanding?

#54

Re: good points, and more on mechanism

William Duffield

The only reluctance I have in calling it a "cap iron" is that the terminology is not descriptive. It sounds like it is just used to hold the blade in place, and could easily be confused with "lever cap" by the novice . Of course "chip breaker" doesn't really describe what it does, either. Maybe Warren's "double bladed" is better, but doesn't keep the novice from trying to install it upside down :D .

Re: Options to eliminate sanding?

#55

we need a new name

Bill Tindall, E.Tn.

To send this tread totally spinning out of control lets begin a campaign right here on WC to properly name the thingy that holds the blade on, yet in experienced hands does so much more,( likely better pursued on the Hand Tool side). I propose "tear-out mitigator" but that is a mouthful and would translate in German to a whole sentence.

If this Forum had a sheep dog to rein in strays it would be barking furiously and running about.

Re: Options to eliminate sanding?

#56

Re: we need a new name

William Duffield

What we really need is a whole new word, but that won't happen because only teenage valley girls with huge Facebook followings are allowed to make up new words. And you may inadvertently start another new debate on the relative merits of Border Collie vs. Australian Sheep Dog vs. Bouvier des Flandres. :D

Re: Options to eliminate sanding?

#57

Re: Are other points missed?

Derek Cohen (in Perth, Australia)

The BU plane was not unknown to Stanley or the planing world for that matter. Lee Valley early on offered a wide selection of these planes to suit any planing desire. So the opportunity was there for the planing world to have another chance to gravitate to BU planes, the first being when planes got invented and then over the next few centuries. Yet to fill an unmet need LV has spent a Herculean effort to recently introduce a BD plane.

So, a skeptic might reasonably ask, if a BU plane is cheaper and more useful why do they remain a minor player in the world of planes, so much so that LV felt obligated to offer a BD plane line with much fanfare? The apparent conclusion is that the BU plane has some disadvantage(s) that the ubiquitous BD plane does not. When in doubt go where the crowd voted with their money was the route I personally took. But I remain open to data showing that the BU plane is better for what I do. Anyone care to bring one by?

Bill, firstly, the BU planes were copied first by LN and then by LV. LV, however, have produced more of these. Further, where LN copied the origonal Stanley designs - with all their foibles - LV have introduced a host of advanced features to their range.

The reason why there has been such a long gap in time between the largely unsuccessful production of the original Stanley planes and the modern LN and LV versions is twofold. One reason is the advent of durable ductile iron used in the body rather than fragile grey iron. The early Stanley were known for chipped mouths (I have one). The second reason is that the method of use changed. The early Stanley planes received a 25-30 degree bevel which, on a 12 degree bed, created a plane that had a low cutting angle. This was only good for end grain ... hence the term "block plane". In modern times the bevel angle was raised to 38 - 50 degrees, and this created a high cutting angle, one that could take on and beat interlocked face grain. Suddenly we had planes that would really preform!

Why do more BD Stanleys exist than BU LV/LN planes? Simply because the Stanley's are cheap and plentiful. Plus, my perception is that the average woodworker in the USA does not work complex grain. Walnut, Cherry, and the like are easy stuff compared with the likes of Australian hardwoods. Here many use planes with high cutting angles, such as the HNT Gordon range. Until the recent renewal of interest in the chipbreaker, only high cutting angles would hack it. BU plans made high cutting angles easier to achieve. These planes are still easier to use, but they are a lot more expensive than a vintage, multi-owned Stanley that comes out of a swap meet.

Regards from Perth

Derek

Re: Options to eliminate sanding?

#58

Funny about that....

John in NM

I never had the least trouble with the "blade-cap iron-lever cap" nomenclature... so much so that I actually get confused by these discussions.

I don't think we give novice's enough credit for paying attention and looking for definitive answers rather than the subjective "some call it this, others call it that" approach.

Re: Options to eliminate sanding?

#59

I forgot....

Bill Tindall, E.Tn.

were we once talking about sand paper? I forgot. I had eye surgery today and have nothing better I can do than rant incomprehensibly on WC. Maybe I go grind a lathe tool....no can't do that either.

Re: Options to eliminate sanding?

#60

At least you're not...

John in NM

Ranting about the computer :D

On the other hand, ranting about it here did at least prevent me from reprogramming it with a very large axe :D

Re: Options to eliminate sanding?

#61

time to take up basketweaving

John K Jordan

This discussion has been educational! I am in awe of those with so much knowledge.

I had no idea there was so much to think about concerning planes. I bought a plane 40 years ago. I don't even know what brand. I don't even know what to call the parts. I've sharpened the blade (iron?) a few times. When I push it on wood chips come out the top unless I set it for too big a bite. The wood behind is flatter.

Some years ago I bought a very nice little baby plane (block plane?) from Highland Hardware. I felt so professional with a collection of two planes! Yikes. Now I rightly realize I'm a clueless uneducated novice bumpkin woodmangler. I am so ashamed. :-) :-)

JKJ

Re: Options to eliminate sanding?

#62

I resemble that remark!!!

David Yoho

Heck, I thought I was the only one.

I bought a #5 Record plane way back and added a low angle block later on. The only difference is I also own a LV scraper plane. All three get a lot of rest in my shop compared to other tools but when the time and need are right I put them to work.

Not to worry John. I think there's still hope for us :)