Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Table Saw Blade Change Problem

Posts

Re: Table Saw Blade Change Problem

#51

Re: I have a poster.....

Barry Irby

Glad you got it. Thank you Bill for posting a picture.

My thought was that the blocks be longer and bear on the table in front of the blade. That way you woudl have wood on the blade and on the table with almost no chance of damaging either of them or the clamp. Bill uses a smaller blade, leaving a longer gap to the front of the slot to the table.

Sounds like an AC in the shop might be in order. I added a little window unit several years ago. A wonderful improvement.

Re: Table Saw Blade Change Problem

#52

Re: I have a poster.....

Larry Clinton At Frankfort, (Central) Indiana

Whew, 110 Deg.! Sure glad I installed a central Air conditioner and furnace when I built my shop! I keep the shop at about 72 Deg. summer and winter. I think it prevents me having any rust issues even when I am not using it. As I super insulated the shop, the additional Gas in the winter averages about $50 a month and summer air I estimate at about $30~40. Worth that to keep the equipment rust free, and wood I have stored stable.

Re: Table Saw Blade Change Problem

#53

Final Solution

Stuart Johnson

From what I have been able to determine the thin kerf rip blade is the problem. There is just enough space between the threads and the backer to allow the blade to partially drop off to the part to the spindle that is not threaded.

I have solved the problem by using the back stabilizer which moves the blade about 1/4". Of course this throws off the tape measurements so I'll need to either remove the one on the fence guide or remember to adjust when setting up a rip cut. I remember now I originally didn't use the back one because my miter sled was calculated without it.

This is the first time I have purchased a thin kerf blade as well as a dedicated rip blade. It has made all the difference in world in my rip cuts. I was constantly trying to adjust the fence, blade height, feed rate and so forth trying to reduce the burn. With this blade there is no burn, smooth cut and no hard pushing. I can see where using the proper blade is very beneficial.

Re: Table Saw Blade Change Problem

#54

Which blades?

John K Jordan

Which blades did you get that worked well?

Re: Table Saw Blade Change Problem

#55

Ripping, burning, thin kerf

Bill Tindall, E.Tn.

A reason to use a thin kerf bade is they require less motor power to run and there is less pushing force to feed lumber past the blade which leads to more secure control. Maybe someone else will come up with other reasons.

Burning is caused by too little clearance between teeth sides and wood which can be a result of inappropriate bade design, dullness or pitch build up (which can be worsened by bade design).

For routine ripping people often get a bade with too many teeth. 24 or less on a 10" blade is optimum.

Burning is something I rarely encounter with a 10" combination blade, a 24 tooth rip blade, or a 7 1/4" x 40T combination blade.

Re: Table Saw Blade Change Problem

#56

Re: Which blades?

Stuart Johnson

The rip blade is: Freud LU87R010 10-Inch 24-Tooth FTG Thin Kerf Ripping Saw Blade with 5/8-Inch Arbor and PermaShield Coating around $38 on Amazon. I use the Freud LU85010 crosscut when cutting clean glue ready segments.

Re: Table Saw Blade Change Problem

#57

Re: Ripping, burning, thin kerf

Stuart Johnson

Burning is something I rarely encounter with a 10" combination blade, a 24 tooth rip blade, or a 7 1/4" x 40T combination blade.

I adjusted the fence every way I could using a Forrest WW II and would get burn half the time. This is suppose to be a top of the line blade so all I can say is it was probably operator error.

Re: Table Saw Blade Change Problem

#58

Re: Ripping, burning

Mark Mandell - Gone Round In New Jersey

When Memsahib discovered Stickley-in-cherry I had to upgrade both the table saw and the blades I was using. The Systematic 24-tooth "glue line" rip has been the workhorse ever since to avoid burning the sugar and pitch in cherry. I've had it sharpened twice, once by a local and once by Forrest [head-bob to Forrest!]. This ain't a thin-kerf blade, however, and I do have to keep the stock moving at an uninterrupted constant speed. I also make sure that my fence is set a Kth or two wide at the back of the blade and always have a splitter in place.

BTW I keep my blades clean with a light application of oven cleaner and a tooth brush. Makes more of a difference than many would expect. I think we get used to blades that slowly get build-up making us have to push harder.

Re: Table Saw Blade Change Problem

#59

That is the problem with Forest bladeses

Bill Tindall, E.Tn.

For some woodworkers the main thing they are concerned with is a smooth cut that doesn't show tooth marks. To get this result requires many teeth and little side clearance on the teeth. The price to pay is more friction of blade on wood and more pitch build up which leads to more rapid dulling.

Forest blades are made to tight specifications for plate and teeth, they have lots of good carbide in the teeth and lots of advertising to convince customers that they make the "best" blade. Indeed it may be the best blade if smoothness of cut is the most important requirement.

Personally, I rarely require a perfectly smooth cut. I normally am refining the width of a ripped piece on the jointer or with a hand plane. I buy Freud or CMT or about any other brand of industrial quality bade that costs 1/2 as much, or less. I just bought 2 CMT 7 1/4" combination blades from Amazon (#251.040) for $25 each. Misenheimer resharpens them for $10 and I get 1 or two resharpening from their tiny carbide teeth. I have enumerated the advantages of this kind of bade many times and will not repeat. But they never burn.

Re: Table Saw Blade Change Problem

#60

Re: Other reason

TomD

"Maybe someone else will come up with other reasons."

My main reason over the years has been reduced waste. For conventional woodworking not a big deal, but as we both make stuff like bent shaft paddles, I am sure you have appreciated this factor also. It is easy to convert more than half the wood to dust when making lams.

Re: Table Saw Blade Change Problem

#61

Re: Other reason

John K Jordan

Less waste is a great reason. Same for sawmills, bandsaw vs circular vs chainsaw mills.

JKJ

Re: Table Saw Blade Change Problem

#62

Re: Less Waste

Mark Mandell - Gone Round In New Jersey

with less sawdust being made, where would IKEA get the needed materials for its furniture?

;)

Re: Table Saw Blade Change Problem

#63

Sawdust

John K Jordan

I'll send them some from my sawmill.

Re: Table Saw Blade Change Problem

#64

Re: Final Solution

William Duffield

I'm curious regarding an important omission in this thread. You never mentioned whether your saw is left tilt or right tilt. Finally, it has become obvious that it is left tilt and your arbor is right hand threaded. If you had a right tilt saw, your arbor flange would be to the right of the blade, and your arbor would be left hand threaded instead. This may have made some difference in our diagnosing of your problem. Also, mentioning the brand and model of saw might have helped, because different saws' arbors are machined differently.

Why do I mention this now? Only because right tilt saws, when cutting using the scale or the fence to the right of the blade (the more common usage) do not have the calibration problem with thin kerf (or with dado) blades. This is because the scale is calibrated to the right edge of the kerf. On right tilt saws, since the flange is also to the right of the blade, changing the blade thickness usually* does not appreciably change the position of the right side of the kerf. On the much more common left tilt table saw, the arbor flange is to the left of the blade, and installing a different thickness blade can appreciably change the scale calibration.

*except in dado and finger joint blade sets.

I partially solved my problems with this issue when I upgraded from a right tilt contractor's saw to a left tilt cabinet saw by replacing my thin kerf blades. All the rip, crosscut and combo blades I use now cut a 1/8" kerf. This strategy is only a good idea if your new saw is at least 3 hp., and it's not useful for dado blades or for extreme thin kerf blades you might use for sawing up packs of inlay banding or otherwise saving valuable wood.

If you do a Google image search on "arbor flange" you should find all sorts of interesting info pertinent to this discussion.

Re: Table Saw Blade Change Problem

#65

Ellis Walentine

Re: Ripping, burning, thin kerf

Ellis Walentine

As Bill mentioned, the low side clearance of the Forrest blade means it will clog and burn much sooner than a standard industrial blade.

Ellis

Re: Table Saw Blade Change Problem

#66

Re: Chipper

TomD

I just chipped about 100 trees today, mostly birch, maple, and oak. It was not as much fun a I had imagined. Hard work also, but it made no terribly visible impact on the property, so I think there is still material out there. :)

Re: Table Saw Blade Change Problem

#67

Re: Final Solution

Stuart Johnson

I'm curious regarding an important omission in this thread. You never mentioned whether your saw is left tilt or right tilt. Finally, it has become obvious that it is left tilt and your arbor is right hand threaded. If you had a right tilt saw, your arbor flange would be to the right of the blade, and your arbor would be left hand threaded instead. This may have made some difference in our diagnosing of your problem. Also, mentioning the brand and model of saw might have helped, because different saws' arbors are machined differently.

Grizzly G1023, right tilt, left hand arbor thread

This is because the scale is calibrated to the right edge of the kerf. On right tilt saws, since the flange is also to the right of the blade, changing the blade thickness usually

I agree, the stabilizing set has two discs, one for each side of the blade. As a result the right side of the blade is moved 1/4" to the left changing the calibration. I had the left side installed when I calibrated my miter sled but not the right. Installing the right stabilizer took care of the sticking blade but has messed up calibration for both the fence and miter sled. Both can be easily handled.