Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Table Saw Blade Change Problem

Posts

Re: Table Saw Blade Change Problem

#26

Re: Table Saw Blade Change Problem

Barry Irby

You could try to hold the shaft by holding the pulley if you can get to it. Be sure to unplug the saw. Hold the pulley or belt and use a mallet to tap the blade nut loose.

Is you new blade thin enough that the nut has locked up on the end of the threads?

Re: Table Saw Blade Change Problem

#27

Re: Table Saw Blade Change Problem

Stuart Johnson

I think I would need at least one additional hand to hold the pulley and tap the nut so I'll wait for the wrench. I had the thin blade on and off several times before it stuck. I got it off and put on the regular 1/8" cross cut that is now stuck.

I can understand things gradually going bad until they stuck or didn't work. I don't understand how something like this happens all at once. Originally I took off the blade I was using and made one rip cut in some dried walnut. Went to change back to the cross cut and it was stuck. I got it loose and replaced the cross cut and cut 16 segments. I then wanted to rip another board and I'm now stuck solid with a blade that I've used dozens of times.

I won't know until I can get the blade off but I wonder if there is a bit of junk between the blade and the arbor flange acting like a wedge. I think that would cause the blade to wobble plus make the blade wedge off center with the stabilizer and nut.

Re: Table Saw Blade Change Problem

#28

Re: Table Saw Blade Change Problem

John Veerkamp

one more suggestion. soak the nut in simple green or other solvent just on the off chance that it has gotten gunned up with sap or resin. ditto the blades.

Re: Table Saw Blade Change Problem

#29

Re: Table Saw Blade Change Problem

Dick Coers

I'm guessing it went bad because the blade has spun on the arbor. You should see some galled steel, both on the blade and the arbor. If the blade is spinning on the arbor now so you can't get the nut off, the same thing is happening when you are cutting wood. If bad enough, you will need a new arbor.

Re: Table Saw Blade Change Problem

#30

Re: Table Saw Blade Change Problem

David Yoho

For the record, I've been using a Forrest blade stabilizer with my Woodworker II on my tablesaw along with the stock washer for more years than I can count. Same thing on my radial arm saw. In the off chance your issue is the nut bottoming out, perhaps adding back the original washer between the nut and stabilizer will resolve things.

About the only time I don't use the stabilizer on the tablesaw is when I change over to my Dado King stacked dado set. Do the stabilizers help or not? I don't know but other than reduce the depth of cut, I don't see where they're hurting anything. If the need to cut deeper arises, I just remove the stabilizer and replace it when finished.

Re: Table Saw Blade Change Problem

#31

My theory

Bill Tindall, E.Tn.

....is that the stablilzers are not seating on the blade uniformly, for what ever reason.

Holding the blade fixed can you spin the arbor easily by turning the nut . If so there clearly is not normal friction between stabilizer and blade.

As far as wobble, blades are designed to stand up "at attention" when they come up to speed. A bit of wobble starting or stopping may be nothing to worry about. I see it on some of my blades. On the other hand if the blade is warped it means the stabilizer did not seat on the blade uniformly. Look into seeing why. Misenheimer, Morrristown TN, can straighten a warped plate. They typically will not charge if part of sharpening.

Do let us know how this all turns out. My curiosity is perked.

Re: Table Saw Blade Change Problem

#32

Re: My theory

Stuart Johnson

Holding the blade fixed can you spin the arbor easily by turning the nut . If so there clearly is not normal friction between stabilizer and blade.

No, if the blade is held nothing will spin. I did use the end of a wrench to really lock the blade and the arbor tried to turn not the nut. I didn't force the issue because I was afraid I would chip a tooth.

Re: Table Saw Blade Change Problem

#33

I'm confused

Bill Tindall, E.Tn.

"No, if the blade is held nothing will spin. " By damn if the blade is held something will turn. Either the nut will loosen or the blade will spin on the arbor or you are turning the nut backward and tightening it.

If the blade spins on the arbor do the stabilizer washers spin with the blade or do they stay stationary with the nut and the blade and stabilizers spin?

" I did use the end of a wrench to really lock the blade and the arbor tried to turn not the nut. " (use a wooden stick) Clarification: You have stuck a wrench through a gullet of the saw. The other wrench is on the nut and when forced the blade spins on the shaft? But the blade spins on the shaft only when considerable force is applied to the nut? And this is after just snugging the nut when the blade was installed?

Re: Table Saw Blade Change Problem

#34

You're not alone!

Dick Coers

I think we're going to need a video to sort this thing out. Not even a picture is going to be enough now.

Re: Table Saw Blade Change Problem

#35

Re: I'm confused

Stuart Johnson

Normally I use a stick to hold the blade and loosen the nut. In this case every piece of wood I have tried to use to hold the blade has in effect been cut when I apply enough pressure on the nut. Nothing turns, not the stabilizer, nut or blade until I apply enough to go through the wood. So I tried using the thin arbor wrench (soft junk) in the gullet and applied pressure to the nut. Neither the blade nor the nut moved but the arbor did turn just a bit. I was afraid of chipping a tooth if I gave a sharp whack or continue applying pressure. So I'm just going to wait until I get the proper wrench.

If I keep going I'm going to think it to death. If the chuck on a lathe isn't tightened snugly and the lathe is started with a heavy piece rather rapidly you can lock the chuck so tight it is almost impossible to get off. I wonder if the blade was too loose and when I started the saw it caused that type of lock.

Re: Table Saw Blade Change Problem

#36

Re: I'm confused

Joseph Mulherin, sr

Stuart, What make of table saw do you have? I might suggest you call the manufacturer and see what answer they might have. I really think the saw blade has come to the end of the thread and got lodged between them.

When and IF you get it loose I suggest installing a large washer on the rear and the locking flanged nut on the front, tighten lightly and just snug the nut....not go whole hog and bear down on it.

Re: Table Saw Blade Change Problem

#37

I think you've answered it.

Keith Newton

I was going to suggest that you may have started the saw with a loose nut. I did that once many years ago, while changing a blade I ran to grab the phone, expecting an important call, the came back and started the saw before I remembered that the nut was still loose. It took everything I could muster to get it loose.

Re: Table Saw Blade Change Problem

#38

An interesting hypothesis....

Bill Tindall, E.Tn.

and one that can be readily tested.

Stuart, if you ever get the blade off reinstall a light weight 7 1/4" blade from your skill saw and see if it locks up....or not. Or install what you have been installing and give it a better snug before starting the saw.

Re: Table Saw Blade Change Problem

#39

Oh!  My bad.....

Barry Irby

This seems to be a different problem. I thought the nut had locked up without securing the blade to the shaft, so that the nut was tight, but the blade was more or less free to spin without turning the shaft.

It seems now the nut and blade are so tight you can't loosen the nut. ???? You are afraid you can't hold the blade without damaging it?

What I would do is clamp a piece of wood on both sides of the blade, with the wood resting on the table. The wood will deform and cushion the teeth and not damage them, protecting them from the metal jaws of the clamp. The put a wrench on the arbor nut and give it a sharp blow with a hammer. Use "impact" to loosen the nut.

I can't remember a wrench with my saw that went on the shaft. (I have had the saw 44 years, so NEW is a dim recollection.) Somewhere along the way I found a box end wrench that fits the arbor nut and I have stuck it to the cabinet with a magnet. It's much better than the thin little wrench that came with the saw.

If you are waiting on a little thin wrench that will fit on flats on the shaft, I don't give it much of a chance. The flats are probably very small and the new wrench won't have much surface area to get a bite. I expect it will be poorly tempered and will deform.

Unplug the saw first.

Re: Table Saw Blade Change Problem

#41

Re:Nope, didn't work

Stuart Johnson

I clamped two boards front and back, gave the wrench a sharp whack. The blade cut through both boards. I guess there isn't anything to do but wait for the wrench so I can keep the arbor from turning. There is an answer but I'm starting to wish I had paid for express shipping.

Re: Table Saw Blade Change Problem

#42

Re:Nope, didn't work

Barry Irby

Wow! This must be really stuck.

It seems to me there must be a misunderstanding here. My suggestion was to put a a piece of wood in each side of the blade. As if you had ripped the wood. Clamp it tightly to the blade. It sounds like you are positioning the pieces as if you were going to crosscut them.

I am dyslexic or dis-graphic or dis-something so I had to go look at my saw. The blade nut is on the left side and to loosen the blade I pull the wrench forward, opposite of the feed direction.

I have never had to do this, but It seems to me if you clamp this tight enough you could not saw through the wood, probably could not damage the blade, but something would have to give.

Re: Table Saw Blade Change Problem

#43

Not what was suggested

Bill Tindall, E.Tn.



Make a sandwich- clamp face, piece of wood, blade, piece of wood, clamp face.

Clamp rests across table of saw preventing blade from moving.

Blocks are not optimally adjusted in picture, but you got the idea. You will get vastly more clamping force with this arrangement than an arbor wrench, if more force is what is needed.

Re: Table Saw Blade Change Problem

#44

Right/left hand thread?

Tom Dunlap

Could this be the issue? It seems basic or even non-related...but...something that hasn't been mentioned so far [I think].

Tom

Re: Table Saw Blade Change Problem

#45

Double checking.....

Bill Tindall, E.Tn.

if your nut is on the left side of the blade, judged from the front of the saw, you should be pulling on the wrench that is on the arbor nut.

Re: Table Saw Blade Change Problem

#46

Have you tried heating the nut?


Re: Table Saw Blade Change Problem

#47

Thank You, Thank You

Stuart Johnson

Thanks to everyone for all the help. Barry's suggestion is the one that worked after Bill's photo showed me I misunderstood what he said. I clamped the blade just like Bill shows and rapped the wrench with a hammer. It came right loose. I took the blade off and made sure both the flange and stabilizer were clean and reinstalled the blade. This time I finger tightened it then snugged it with the wrench. After running the saw for a bit I removing the blade. The nut turned with the normal amount of pressure.

It's 110 in shop right now but in the morning I'm going to be a glutton for punishment and lightly finger tighten the nut and see if the jam repeats. The result from the test will hopefully be the end of this thread.

Thanks once again for all the help.

Re: Table Saw Blade Change Problem

#48

A picture is always worth...

David Yoho

a thousand words!

Re: Table Saw Blade Change Problem

#49

I have a poster.....

Bill Tindall, E.Tn.

It says......"All's well that ENDS."

110 in the shop! I could not think well enough to solve any problem in that heat.

Re: Table Saw Blade Change Problem

#50

Re: I'm confused

Joseph Mulherin, sr

Stuart, turn the saw over and remove the motor entirely.e able to get the darn thing loose.... With it loose you might be able to get it loose if you still want to.

Go buy a new motor and arbor and new saw blades and make sure they are correctly mounted before starting the saw