Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

table saw sawdust

Posts

table saw sawdust

#1

  table saw sawdust

Jack Putnam

I am working on a project where I need to cut a 45 degree angle on a piece of wood on my table saw. now the wheel that you turn to do this is on the side of the table saw the make of the table saw is a RIDGID. The problem I am having is that the wheel that you turn to get the different degrees will only go to 35 degrees. It seems that the sawdust has collected on the shaft that is where the gears mesh. (I guess you call them gears) in order to make the saw blade turn to a 45 degrees some how the sawdust hast to be cleaned out.

There are no panels to take out and the only way I can see is to use an air hose to blow the sawdust away and by looking through the slots in the front metal panel even then you can't see very well what's going on. Does anybody know of an easy way to clean the sawdust out I don't even think you could grease that area on the gears it would make it worse. Thanks for any help you can give me.

Re: table saw sawdust

#2

Re:   table saw sawdust

Joseph Mulherin, sr

Turn the saw over

Re: table saw sawdust

#3

Re:   table saw sawdust

Jesse Cloud

Joseph nailed it. If you can't turn the saw over, try coming in through the blade area. Take off the throat plate, remove the blade, etc. Then use a brush (with a long handle if you have it). Use something that won't scratch the gears, a brass brush or an old tooth brush.

Blowing out with compressed air is bad for you and may be bad for the saw's bearings.

Use a dry lithium grease, an auto parts dealer will have it. Run the wheel up and down a few times and it will work like new!

Re: table saw sawdust

#4

Re:   table saw sawdust

Joseph Mulherin, sr

Thank you, Jessee, I am not that eloquent.

Re: table saw sawdust

#5

Re:   table saw sawdust

Lee Schierer in McKean, PA

You will want to lubricate the threaded shaft and the Gear with paste wax or a dry bicycle chain lube. Using a grease that remains tacky will only catch more sawdust. It is also a good idea to run the saw to full up/down and full tilt from time to time to keep the sawdust to a minimum. Some trunnions have curved slides that the saw carriage rides in and these can accumulate saw dust as well.

Lee

Re: table saw sawdust

#6

Re:   table saw sawdust

Joe shelton

Removing the gunk is important, and inverting it onto its table is the right way to do that.

That saw also has a potential problem with fouling the motor mounting plate on the rear rail. Check that, too.

Re: table saw sawdust

#7

Re:   table saw sawdust

Jerry Gibbs

I agree with what's been said. Cleaning the sawdust out will have the biggest impact.

Re: table saw sawdust

#8

Re:   table saw sawdust

Matt Robinette

I would make sure the blade clearance insert is removed before moving to 45 degrees. I have had the blade bind on the insert and not move all the way to 45. I had to drop the blade all the way down then move it to 45 degrees then move it back up cutting the clearance needed in the insert.

Re: table saw sawdust

#9

Re:   table saw sawdust

Joseph Mulherin, sr

Matt, are you using the ORIGINAL insert...or did you make another one for closer clearance for very small cuts? I always use my original except when I do need the closer clearance for when I am cutting slats on the table saw. But, I mostly cut the slats on my band saw because it takes much less kerf on the cuts.

Re: table saw sawdust

#10

Re:   table saw sawdust

Matt Robinette

I have had to cut the bevel into the insert on the zero clearance inserts on the Jet Xata Cut I had and the saw Sawstop I have now. The Craftsman contractor saw I had until 15 years ago came with wide clearance metal inserts would readily swing to 45 degrees without interference with the stops set correctly but i ended up going with shop made zero clearance with that saw also. I have not found sawdust to impeded the trunnion travel on the saws that I have owned. It was operator error on my part on not setting the saw up properly for the operation i was trying to achieve. Your experience may differ.