Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Lathe problem

Posts

Re: Lathe problem

#26

Kneale Brownson

Re: Take Pictures & put parts in order

Kneale Brownson

When I disassemble something unfamiliar, I put the parts I take off in order of their removal. For example, if it's something small, I use old egg cartons with each part put in separate spaces in the order they come off.

Re: Lathe problem

#27

Re: Lathe problem - my question

Gordon P Patnude

A-J:

What part of the country do you live in??

Perhaps there is a wood turning group in your area that has a member near you who would be willing and able to help you sort this whole problem out.

Just use Google to search for wood turning groups or woodturning groups]

Most of the guys in my group are very knowledgeable and also helpful to guys who are having problems.

Re: Lathe problem

#28

A.J. Hamler

YouTube video with motor sound *LINK*

A.J. Hamler

OK, I figured out how to post a YouTube video, which can be found at the link that should appear here.

It runs :31 seconds and starts with the lathe off. Then I click it on at the lowest RPM, then ramp it up in steps to top speed and then back down again.

Not much to see, but since the sound was the most important part I got the camera as close to the motor as I could so the camera mic could pick it up. The noise appears to be coming from the back end of the motor (right side here).


Lathe motor noise

Re: Lathe problem

#29

Re: YouTube video with motor sound

Bill Howatt

I don't have any experience with a VS DC motor like your lathe has so take my comment with a grain of salt.

It sounds like a bad bearing in the motor and perhaps the extra movement from the bearing is also causing more brush noise. Perhaps something is loose in the motor?

Sure seems noisy but then there could be influences from your recording equipment. Is it that noisy when you stand in a normal turning location at the lathe?

FWIW,

Bill

Re: Lathe problem

#30

A.J. Hamler

Re: YouTube video with motor sound

A.J. Hamler

Actually, it's louder. The tiny mic in my camera doesn't do it justice.

Re: Lathe problem

#31

AJ, I couldn't see much of the motor,

Keith Newton

but I'm wondering if there is something touching the fan blades?

Sometimes, the ends which protect the fan can get dented causing the blades to touch the cover. This is about the right pitch I would expect to hear.

For TEFC motors, there are just 3 bolts to remove to get the fan cover off. Then is is easy to beat the dent out with a hammer.

But if it is an open frame motor, maybe a wood chip got in there and is toughing the fan blades.

Re: Lathe problem

#32

Re: AJ, I couldn't see much of the motor,

Larry in NW Ohio

AJ I use to work on these type of motors years ago, and as Keith said it sounds like a rubbing sound coming from the fan housing rubbing the fan or some thing else that may be rubbing it. That sound is just the same as the fan housing rubbing something. The first thing I would try, is to take the housing off and run the motor and see if you get the sound. If you still get it, try taking the fan off and run it and see if the sound is still there. It`s not going to hurt the motor if you only run it no more than you did in the video. Good luck Larry

Re: Lathe problem

#33

A.J. Hamler

Re: AJ, I couldn't see much of the motor,  *LINK*

A.J. Hamler

There was nothing out of the ordinary to see (no dented cover or anything), so I put the camera way up close to get the best sound and didn't worry about the visuals.

I'll take that cover off and see what's inside.

Thanks!

BTW, I wrote about this whole experience on my Woodshop News blog ---


Woodshop News blog

Re: Lathe problem

#34

A.J. Hamler

Re: Lathe problem -- end "fan" cover removed

A.J. Hamler

OK. It took nearly a half hour to do it, but I finally got that "fan" cover on the end of the motor off. Again, the screws are nearly inaccessible without removing the motor, but I finally got it. (Stripped at least one screw, of course, so I'll have to replace that.)

So I get the "fan" cover off and... no fan there. No fan blades. Nothing at all what I was expecting. What's there is a short extension of the motor shaft, about an inch or so, with a wheel on the end. Attached to the end of the motor with a small bracket is a small--very small-- circuit board with a red LED or diode on it. There's a wire that runs through the cover I just removed (the cover is hanging from the wire) that attaches to that circuit board. That circuit board is mounted right near the wheel, but not touching it.

With the cover off and dangling, I ran the motor as before, and the sound is still there but a bit louder with the cover off, and it's definitely coming from the area of that little wheel and circuit board. To the best I can see, nothing is rubbing. On a hunch, I switched the motor into reverse and the sound nearly disappeared. It's still there although I doubt I would have noticed it with the cover on. I went back and forth from reverse to forward a could times -- in reverse, there;s almost no sound; in forward, the sound is loud as it was before.

It's gonna take some gymnastics to get a photo of the wheel/circuit board, it but I'll give it a try and post it later.

A.J.

Re: Lathe problem

#35

Re: Lathe problem -- end "fan" cover removed

Larry in NW Ohio

Without the fan being there, I`m guessing, of course, the noise is coming from your wheel in the electronics, maybe. now that you have the cover off see if you could get a 1/4" dowel rod, maybe 12 inchs long give or take. Use it to touch the various areas around the wheel to see where the noise is coming from. Try and touch a screw around in there. Put one end of the dowel to the screw and the other end put on your thumb and your thumb tight up against your ear. That will give you an idea where it may be coming from. Good luck. Larry

Re: Lathe problem

#36

If you take any more photos, how about

Keith Newton

including one of the motor name plate.

Have you contacted the manufacture yet. They may have someone who has already had to troubleshoot this before.

Re: Lathe problem

#37

Have you Googled this issue?

Dick Coers

Lots of others out there with the same issue. Couldn't find a specific fix.

Re: Lathe problem

#38

Re: Lathe problem -- end "fan" cover removed

William Duffield

Those parts are your tachometer. It senses the rotation of the motor shaft and sends a signal to the DRO on the speed control. It is part #s 57, 58, 59 and 60.

Three of those parts are metric pan head screws, one is the mounting bracket and one is the sensor itself. The screws adjust the sensor on the bracket, to get the sensor close enough to the motor shaft to sense its speed without getting close enough to rub. You may have a loose screw or an out of adjustment bracket that are allowing the sensor to rub on the motor shaft. Adjust and retighten. If you've got it right, the whine should go away, but the speed digital readout should still display a reasonable speed. The manual doesn't give a gap spec. The parts diagram also doesn't show what the bracket is screwed to. It looks like the screw heads are #1 Phillips, but they might be allen head. Note that there is also a data cable connected to the sensor. It doesn't show where is it connected, but Figure 17 shows that it plugs into the circuit board on the speed control unit. Note that there is another similar sensor in the headstock that senses the spindle speed. Some day, you may have to adjust that one, too, if for instance you need to replace the drive belt.

Re: Lathe problem

#39

Re: Lathe problem -- end "fan" cover removed

Tony - Memphis

Most of the Hall effect sensors work with around a 1mm gap (or at least the ones I play with). I'm working on building a tach using them to attach to my DP, lathe, etc. Mainly just for fun.

Tony

Re: Lathe problem

#40

A.J. Hamler

Re: Lathe problem -- end "fan" cover removed

A.J. Hamler

OK, I checked that tachometer sensor thing out left and right. There's a gap there and NO rubbing whatsoever. I spun the shaft by hand and there's OK clearance the whole circumference. Everything is tight; no loose screws, no loose bracket.

I managed to get my head up under the lathe and ran it, and now with the cover off and out of the way, the sound seems to still be coming from that end of the motor, but from inside. I blasted some air in there from the compressor just in case there was anything loose inside that had gotten in, but the noise is still there.

I think I've ruled out that tachometer sensor, and now I'm thinking motor bearings -- are there bearings on that end? Would motor bearings make a lot of noise when the shaft is rotating in one direction, but very little noise when rotating the other?

Thanks again everyone.

A.J.