Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Question ???

Posts

Re: Question ???

#26

No. It's Bob Vila

robbcarr

I think it's suppose to be Bob Vila. He was the one that was hawking Sears/Craftsman tools.

Re: Question ???

#27

Sweet !!


Re: Question ???

#28

Still Is

Mark Mandell - Gone Round In New Jersey

Last time I looked ;)

Re: Question ???

#29

Re: No. It's Bob Vila

roger lance

Well, even though the figure has a beard and is wearing a plaid shirt (two Norm trademarks).....it's hard to believe that Jesus, who was a carpenter, would ever get perturbed with a fellow carpenter as good as Norm.....but Bob Vila is a different story.....so, maybe you're right!!

Re: Question ???

#30

Re: No. It's Bob Vila

William Duffield

No tool belt, no routah, and no measured drawings. Couldn't be Norm.

Re: Question ???

#31

Actually *LINK*

Mark Mandell - Gone Round In New Jersey

Deering has issues with Mr. Villa


Shellacing

Re: Question ???

#32

Re: Issues?

William Duffield

That's not surprising. Even I have issues with Bob Vila. He isn't nearly as good at what he does best as, say, Billy Mays. :D

OTOH, any issues I may have with Norm Abram are trivial. I do think he makes a little too much use of brad nailers. Even in that regard, a pneumatic 23 ga. pin nailer and Titebond Molding and Trim are wonderful. His minions, often referred to as Normites, can be irrational fanatics, but Norm did almost nothing to ever encourage them. The one exception may have been the NYW episode on the iconic Shaker Candle Stand, where he bragged that the only hand tool he used was a utility knife, probably a Stanley 99E.

While I'm on a rant, there is only one "L" in Vila, and no "S" in Abram.

Re: Question ???

#33

Re: Issues?

Mark Mandell - Gone Round In New Jersey

Picky ain't we? :D

Re: Question ???

#34

As I've told offenders on many occasions…

Rod Peterson—Ormond Beach, FL

…and no "S" in Abram.
Abram is a carpenter, Abrams is a tank, It's an "ah, ha" for them, every time.

Rod

Re: Question ???

#35

Re: Utility Knife? *LINK*

William Duffield

Hey, Rod,

While I've got your attention, I didn't see the utility knife on your list. Can you confirm, or correct me if I'm wrong, was it a Stanley 99, or is it impossible to make out which one he used?


http://www.normstools.com/normstools.shtml

Re: Question ???

#36

Re: Issues?

William Duffield

I didn't think I was being picky. We all make spelling errors, grammatical mistakes, and typos. If I were going around scolding people for misspelling difficult words, like "inconsequential" or using "to" instead of "too," or not using semicolons where appropriate, or not italicizing Latin words, that would be picky, to say the least. Misspelling a person's name, especially someone as important to us as Norm, and especially when the error is as widespread as it is, that is important, because it insults, or at least hurts the feelings of, the person whose name is mangled.

I think everyone would be offended if we misspelt the name of the other Carpenter represented in the cartoon.

Re: Question ???

#37

Both

Rod Peterson—Ormond Beach, FL

…was it a Stanley 99, or is it impossible to make out which one he used?
As the subject line says, I covered both bases. He did use a #99 (as has most everyone), but there were a couple of times he used a clone. No telling who made that. Heck, I have one or two like that.

It's under Miscellaneous as Utility Knife. Even though I have a Neanderthal section, I never thought of putting it there, because it's, well, utility—sort of an everyman, if you will.

Linked for your convenience.

Rod

Re: Question ???

#38

We All

Mark Mandell - Gone Round In New Jersey

deal with our varied and multifaceted OCD as best we can.

[What? You didn't know that verbosity was a symptom of OCD? Tsk Tsk}

Re: Question ???

#39

A criticism I had of Norm was..... 

roger lance

although he had just about every clamp known to man, he favored using an air nailer when he could have glued/clamped instead and saved those nail holes in his finished pieces. So I try to do the clamp/glue thing where I can....but sometimes it gets a little much....