This past weekend I was able to get all of the brick that we took off the house cleaned off, stacked, and ready for reuse on the addition of our house. The MIL is mostly all packed and we will move her when she gets everything scheduled. Her house is sold and they closed on that already. Today I get to meet with my general builder and I will tell him what parts I'm going to do and I'll find out what parts he's going to do. I just want to get this show on the road and see some real progress for once.
Well, gotta run and get ready for my builder. What did YOU do this past weekend?
My neighbor is a school teacher in one of our Valley cities and had some stucco breaking off his rented house. I had the materials in my shed that were not being used, so I gave him those and instructed him how to go about doing the repairs. He and his girlfriend patched up the missing blotches on the front exterior and he is going to paint it today after school. I also had mixed up some paint to cover some graffiti on my alley fence wall and gave him the remainder to cover the stucco patches...even the entire lower walls...about 200 sqft I think.
Used my DeWalt track saw for the first time. Cut several 97" x 3" strips. Like the saw, but need to add dust collection for that mdf! I would have had a difficult time handling the entire sheet in the table saw and keeping the sheet tight against the fence. The DeWalt seems well made, but it is the only track saw I have used. Jerry
Turned my car-hauler into self loading log trailer
Keith Newton
I have been wanting to do this for years, and finally did it.
A few weeks ago, I posted over on the turning forum how I had cut down, and loaded a ~24" walnut log, and loaded it onto this trailer single-handed, without the aid of any power equipment. Right after that I acquired a 42" D log, and needed to get it to my shop. There is a serious difference between the weight of these two, so it was time to gear up a bit. That looks like a little chainsaw on the end, but it is a 391 with a 25" bar.
Last week I bought a 9000# winch, which I mounted on the frame up front, then over the weekend, I welded up a boom, which at the base, is pinned on both sides about 3' from the back. It is guyed with a chain on each side, and can pivot fore and aft, for different functions, like loading, or off-loading. I can have it straight up, if I want to flip a lot over, or have it hanging out over the back to flip a big log after it is already on the mill.
I sure need to get the solar kiln finished. I'll be getting some 18" w x 10' L QS red oak boards out of this log. Those would make some fine looking table tops, with just two book matched, for a 36" wide top. These are rift, but the next few will be all QS.
I got out this morning and started sawing, but my last blade was starting to wander. I have some new blades on the way, and others off for sharpening.
Re: Turned my car-hauler into self loading log tra
Adam of Oakland
whoa there, those slabs will be absolutely gorgeous, Keith! and very clever hauler rig to get it home. what i wanna know is what the Makita hand drill used for in the picture next to the splitting maul :-)
Thank you, Joanne, also he wants an evap. cooler for the low humidity here in the desert to use instead of the a/c, so I went to the Home Depot and found one that will be good for his home at a reasonable cost.
I shall also install it for him.
Hey, this being neighborly is morally correct and I think we older people should help out the youngsters in situations like his. He is a good man, a good teacher, and just a good all around nice person.
I usually just mark a plumb line through the pith on both ends. I then screw a long straight board a little to one side, then saw right beside it, trying to keep my bar plumb as I move along. Sawing straight down, makes a great pile of dust just ahead of where I'm sawing, making it hard to see any kind of mark. If I don't hit it perfectly, I drive some wedges in to finish it off. I had just finished doing that before taking that pic, and thought the tools would help give perspective to the size.
Joe You are a very good neighbor. You are what all neighbors should be like. Would you be available this coming weekend to help cut some logs up, and split them. Larry
In addition to my helping out my neighbor, I am refurbishing a small bicycle that my grandson had when he was three yrs old, and am going to give it to my great-grandson in June or July. It is the same bicycle Chris had and David is his nephew.