Dedicated Electron Burner
Mark Mandell - Gone Round In New Jersey
I do the break-down shake-down outside with a 8" worm drive. Wet or dry, the beast blows through most anything up to 10/4 and as wide as I want to get it to manageable size.
Knowledge You Can Build On — Est. 1998
Dedicated Electron Burner
Mark Mandell - Gone Round In New Jersey
I do the break-down shake-down outside with a 8" worm drive. Wet or dry, the beast blows through most anything up to 10/4 and as wide as I want to get it to manageable size.
Re: Let the debate begin-radial arm v. compound mi
James Heaston
Brian: You're right. Just like yours mine has casters on it & is out of the way, sort of. It's great to have around to put stuff that I don't have a better place to put it.
I haven't the scrap metal guys come for it yet as I think about getting one of these for it ....
http://woodworker.com/radial-saw-mortising-attach-mssu-889-372.asp?search=ras%20mortiser&searchmode=2
Re: Anyone use the Inca RAS?
TomD
Can't say it has that friendly alumihobit feel their other tools have, but they made it, and it would be fun to run across some day. All their other tools, other than the 20" bandsaw have been through my shop.
The dust seems settled.....
roger lance
I'm impressed with the comments made involving RASs. Normally, there's just talk about how dangerous and outdated they are.....but, in this discussion, folks made some intelligent observations regarding the proper and safe use of this tool. Refreshing.....who knows, maybe we can also talk about the utility of workbench tool trays as being more than "havens for mice".....maybe not??!!.
Re: Lumber "breaking down" saw
Lars Parrington
I do almost exactly the same thing, although I just use a regular panel saw to make the cuts. Maybe it takes me 2 minutes to set up and make the cut. That time is dwarfed by the time I spend just staring at boards and scratching my head before I start cutting.
Determining how best to utilize the wood is a quiet thoughtful process, and the handsaw preserves that tranquility. It also allows a few extra seconds to realize you are about to cut in the wrong place.
Later on in a project I'll use a tablesaw sled for almost all crosscuts due for the sake of accuracy, squareness, and smoothness, and sometimes for it's speed. I have a digital readout on my tablesaw fence, and often employ it as a stop for crosscutting. It's a very fast way to dial in any length to ~0.005" accuracy.
Question
Bill Tindall, E.Tn.
First, before the question, I agree on the meditating process before the lumber is cut. A fair amount of the wood I work for interior parts is #2 common. Some though on what to cut, and where, results in little waste. But even when cutting the best lumber for tops and sides, thoughtful analysis of the lumber can lead to better matching panels. I used to use a cross cut saw for lumber breaking down. And then one day I saw the firewood saw hanging there and I thought, this may work. It did. Outstanding.
How do you use a digital fence for a stop, given one can't directly use a fence for a stop? Something needs to be clamped to the fence to provide clearance between blade and fence for repetitive length cutting. With this block clamped in place now the digital readout is off by this block thickness.
Re: And they are loveable...
TomD
Found this one online while looking up some other stuff.
Re: Question
Lars Parrington
There's a few options.
1. My fence is a delta unifence. Loosen a couple knobs, and I can pull it back so it stops before the blade.
2. Just use the fence like it is. In practice this works fine for me. In theory, the wood could bind between fence and blade causing a kickback. I try not to use this option.
3. Use the fence to locate the board, then move the fence out of the way before making the cut. Good for one-offs.
4. Use an extra block between fence and workpiece. Use the fence to locate the block, then use the block to locate the workpiece. Either remove the block before cutting, or clamp the block to the sled and then move the fence out of the way. Note that this method doubles the inaccuracy (since the blocks will not be perfectly the right length).
I usually choose #4. My sled extends about 20" to the right of the blade, so for short pieces, this is the only valid option. I have a couple blocks made up currently, one 12" and one 18" long (using 10" and 20" instead would make math easier). Blocks are easily made from scrap using option 1 or 3 above.
Note that the digital readout can be temporarily zeroed at any location without losing track of its absolute position. This comes in handy for making differential measurements / cuts.
I might love this one more if.....
roger lance
it had some safety gear around that exposed blade.....and a fence as part of the table.....just to name a couple of things at first glance. RASs shouldn't be cuddly.....more industrial maybe.
Re: I might love this one more if.....
TomD
On mine, the fence is just clamped into place with the rest of the deck. That way you can move it to whatever position best suits the blade and cut in question. Whether something looks industrial or cute really won't help your hand one way or another. It is just a mater of fashion. Sometimes safety gear will help. The main issue is not to put your hand in front of the blade, and to operate the saw with the arm braced. Not to difficult for anyone who may be let loose on the highway at other times. I would not want to operate an unguarded saw as a job since eventually you are going to screw up, but that shouldn't happen in the shop. One of my worst injuries came from dropping a Japanese plane blade on my foot. what a soaker. I guess the funny thing about a job is doing the same thing over and over, and about a hobby is never doing the same thing over.