Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Samantha's Dresser 11-veneering the drawers

Posts

Samantha's Dresser 11-veneering the drawers

#1

Samantha's Dresser 11-veneering the drawers

Bill Tindall, E.Tn.

Samantha’s Dresser -11 Veneering the drawers

In the last installment the veneer was sawed with a target thickness of 3/32”.

PIC 1


Next was selecting the veneer to use and where to cut it for the area to be covered. The lumber for this veneer was cut for me some time in the early 1970’s. It has been a long time to come up with a good use for it. I found that I could saw and joint this thickness just like a normal thickness board. A hand plane and shooting board was handy for adjustments of the butt joint.

PIC 2



These tools were considered for glue spreading. The Headley shop uses the paint brush and white glue. David Finck uses a credit card with notches filed in the edge. Others suggested a foam paint roller. The paint roller is a clear winner. BTW, it can be stored for days wrapped in plastic wrap and readily washed out in hot water. I used white glue for no better reason that it works for the Headley shop.

PIC3


Who ever invented vacuum bags deserves much praise from amateur veneer appliers. The price of these bags has come down a lot. I have used vinyl and urethane bags. The urethane are much easier to manipulate and seal (they are more limp).

After the glue is applied wrap the assembly with blue tape to keep the veneer from skidding. The blue tape is easily removed with little risk of grain lifting.

PIC 4



The result. Each drawer is veneered with two butt jointed pieces of veneer book matched from consecutive sawed pieces.

The next installment will describe fitting the drawer fronts and dovetailing the drawers.

Re: Samantha's Dresser 11-veneering the drawers

#2

Re: Samantha's Dresser 11-veneering the drawers

Hank Knight

Bill, that looks great! Nice job.

Re: Samantha's Dresser 11-veneering the drawers

#3

Re: Samantha's Dresser 11-veneering the drawers

roger lance

Sunlight-In-Her-Hair will keep this with her and remember you always. Another beautiful piece.....love the veneer work.

Re: Samantha's Dresser 11-veneering the drawers

#4

Re: Samantha's Dresser 11-veneering the drawers

Joanne in Point Pleasant, PA

Stunning! Nicely done.

Re: Samantha's Dresser 11-veneering the drawers

#5

PS.... butting the joints

Bill Tindall, E.Tn.

The butt joints were jointed with a low angle plane and a shooting board. As seen in the picture the joint is taped, but in a special way best done with a helper. The joint is held together while stretched lengths of tape are applied across the joint. The spring of the tape applies "clamp pressure" on the joint.

As glue is applied to the veneer the joint is opened a small amount using the tape as a hinge and glue forced into the butt joint. The joint is closed back up and glue applied to the remainder of the surface. Presumably this glue provides some bonding of the butt joint.

Re: Samantha's Dresser 11-veneering the drawers

#6

Re: Samantha's Dresser 11-veneering the drawers

Joe in a Cleveland suburb

Awesome work. Those drawer fronts are really nice looking.

Very nice.

Joe

Re: Samantha's Dresser 11-veneering the drawers

#7

Ellis Walentine

Nice job, Bill

Ellis Walentine

You're convincing me that I should proceed with my plan to resaw an outrageous piece of sapele that I've been hoarding. Talk about multiplying the effect...

Thanks for the write-up and pix.

Ellis

Re: Samantha's Dresser 11-veneering the drawers

#8

Re: Samantha's Dresser 11-veneering the drawers

Larry Clinton At Frankfort, (Central) Indiana

Beautiful work Bill! I'm sure that piece will remain in your family for many generations. I hope you "Sign & Date" the piece in an area that can be seen by future generations - like a drawer bottom or inside a drawer....

Re: Samantha's Dresser 11-veneering the drawers

#9

The provenance

Bill Tindall, E.Tn.

Usually I am building from wood where I know its history and my children knew something about where it came from or who sawed it. I like to put this information in the case using permanent fine tipped marker and then overcoat with shellac.