Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

drill press advice

Posts

drill press advice

#1

drill press advice

Bruce, a MN Galoot

I've been looking for a drill press for a very long time. I have no intention of buying new, only interested in a classic floor model, preferably some gem that others have not recognized and the owner hasn't beaten to death. For the longest time I've been convinced that only a floor model would work. However, I've not been able to find any in the central Minnesota area, at least ones that aren't completely shot.

My question has to do with a floor model compared to a heavy-duty bench model.

Does anyone have any light to shed on a comparison?

Thanks.

Re: drill press advice

#2

Re: drill press advice

John Lucas

I bought a floor model Delta as my first drill press. Still have it and love it. 95% of what I do on it I could do on a bench model. However it's that 5% or even less when it really pays off. On those rare occasions where I have to drill into the end of a spindle or sideways into a really thick board that make me glad I bought it.

It's hard to find good ones on the local sales. I've seen a lot of drill presses but in my opinion they are over priced to even far over priced. I did find a radial drill press for $100 and bought it. It needs some work but not much. Not sure where I'm going to put it but there have been several instances when it really would have been useful.

I'm looking for a really heavy duty drill press to drill large holes in steel but haven't found anything small enough to fit in my shop. Used machines of this caliber run more, $300 to $500 but they are worth probably $1500 new, I've been looking.

Re: drill press advice

#3

Re: drill press advice

roger lance

Bruce....I've never had a bench top press, so I can't offer much for comparison. I've got a Delta 17-900 which I got new 20+ years ago.....new presses have more capacity....but this is a good dp.....I will say that I use this tool on just about every project/build I make....I'm really amazed at how much it is used/needed....I think people under value the importance of this tool.....so I'm encouraging you to get a good press (floor or bench)....you'll be glad that you invested in this tool.

Re: drill press advice

#4

Re: drill press advice

Bill Howatt

I have a reasonably sized bench model and like John Lucas said, it does 95% of what I want it to do and I may even go out to 98%. But every now and then you need the extra height and it does take some bench space away or more likely the base gets used as junk storage area on the bench.

A floor model takes relatively little floor space compared to other WW tools and if I were to start over, I'd get a floor model.

Bill

Re: drill press advice

#5

Thanks, guys,

Bruce, a MN Galoot

everything you all said only reinforces my own inclinations, to get the floor model and be done with it. The project I'm working on now, fixing a chair for a friend, has three separate operations that couldn't be done without a floor model DP. That alone should have told me something.

Re: drill press advice

#6

Re: drill press advice

Ron in Sterling, CT

Bruce,

I was in the same position as you a few years back. I finally bought a good, used bench top dp and used it for a couple of years, when a used floor model came up on Craig's list that was reasonably priced. I bought it, sold the bench top dp and have been happy ever since.

Ron

Re: drill press advice

#7

top heavy

Jerry Gibbs

Floor models can be top heavy, so they need a good base. Be careful if you want to roll it around. Jerry

Re: drill press advice

#8

Re: drill press advice

Larry in nw ohio

Bruce I suppose that alot of people here are going to roll their eyes and say oh yea sure with my opinion, but here goes a

nyway. I have an old Craftsman That I got about 30+ years ago and it has done everything I wanted it to do, even with Metal every once in awhile. It`s one of the last ones that was made in the USA. If you go to Ebay they have really good ones for $200-$300. and in very good shape. If your maybe interested I`ll get the Model # for you. Good Luck with whatever you get. Larry in nw ohio

Re: drill press advice

#9

Re: top heavy

Bruce, a MN Galoot

I've heard that warning before, but it's a good one. I have no room in my shop for moving anything, so as soon as I carve out some floor space, it will stay put.

Re: drill press advice

#10

bench space is more valuble than floor space

Bill Tindall, E.TN.

I watched for a sale at Lowes and snagged a new one that I like and it was not to expensive. But, I am mostly drilling wood or thin metal.

Re: drill press advice

#11

Re: drill press advice

Butch...Mn

Here is something to consider. I needed another drill press to compliment the large one (used for metal and it has varible speed, 20" capacity, power feeds, 6"+ quill stroke and a very large verticle range) I had in my farm shop a couple of years ago. I found on CL just south of the Twin Cities, an old Walker Turner floor model that had surface rust sans a motor. I cleaned it up, repainted it, put on a 3 phase motor, and added a VFD. It is very handy to use and has speeds from zero to double the normal motor speed by merely turning a dial instead of messing with step pulleys. It is a great little unit for both me and my wife to use for our wood projects. I dare you to try buying something new like that at a reasonable cost.

Re: drill press advice

#12

Re: drill press advice

Bruce, a MN Galoot

That's just what I'm looking to do, Butch. However, I've been looking for a DP on CL for three years. I've been beaten by as little as 15 minutes. I once had a conversation with a guy from Mpls who had EIGHT drill presses, just because he likes them. And I can't find one.

As far as three phase, I can't get it. The three phase feeder runs across the street (it's 14,000 volts, though, a bit much :D ), and the power company won't provide it, and I work for the utility.

I'd love a Walker-Turner. The one I just missed on was a Clausing.

Where are you located?

Re: drill press advice

#13

Re: drill press advice

Gary Smyth

Keep looking. They are out there. I see maybe 4-5 each summer. Hovering around $200. Mine are Craftsman and oldies 113. 21370 and 113.213780. Both have the bicycle chain 27587 elevator lift for the heavy table (almost a requirement for these models). Neither is beat. I've had one for a long time and the other for about three years (out of a Pennysaver ad). They delivered it too. They have done everything I wanted in wood and up to 1/4" mild steel plate. I know that two are overkill, but I use them both on most house projects. One for drilling and one usually is used for template edge smoothing or jig angled holes.. I favor the floor models by a lot. The wood cabinet can be lifted away when required and carries bits and cutters. Each is on a 3/4" plywood and ripped 2x4 "fitted" 2" castered base. House sales, Pennysaver, Craigs List, are my best places to look. Oh, and if you spy one just ask if it's for sale - even if not advertised. Some just sit there for years and if you make an offer....?

Re: drill press advice

#15

3 phase

MikeL

Butch is running his off of single phase power through a VFD which has the added bonus of variable speed operation.

Maybe put a WTB on OWWM site. There's a lot of members there from the gopher state with _very_ well equipped shops who periodically offer equipment.

Re: drill press advice

#16

Re: 3 phase

John in NM

A 3 phase drill press and a VFD would be heaven :D :D :D

No more belt changing!

Re: drill press advice

#17

Re: drill press advice

John in NM

Bruce, I have a bench top drill press, an old Rockwell from just after they bought out Walker Turner. So far, the only thing I've needed a floor press for actually worked pretty well by drilling in the lathe. Ideally, I'd have two, one floor, one bench :D But drill presses are just as scarce here as up there.

Re: drill press advice

#18

Re: drill press advice

Brad Patch

First bit of advice, stay away, far far away from import drill presses. Fit and finish is poor, the supplied drill chuck leaves a lot to be desired.

An old model american made drill press, regardless of manufaturer, will be superior to newer models, much better engineering, built to last, better fit and finish, much more good old cast iron

A table that cranks up and down is almost a must, A quill lock is a must, a lot of quill travel is desirable. What is most overrated is a tool offering 12-16 speeds If your primary focus is woodwork than I'll bet you will use only 2 speeds. I have drilled numerous holes fron 1/8 to almost 3 inches and only changed speeds once in one year.

My experiance is with old Delta drill presses and parts are plentiful. Lots of info on Vintage Machinery.com

Re: drill press advice

#19

Re: drill press advice

Butch...Mn

Bruce, send me an email moline at agwireless.net

Re: drill press advice

#20

Re: 3 phase

Jason Waters

I agree,

I did that on my Jet Drill press. I have a 3/4 hp Delta 3 phase motor (I got off my used bandsaw which I put a single phase on) and a $100 VFD that was 110 V in, 230 V 3 phase. I wish I did it years ago. Of course, you need to be handy to wire it up and such.

Jason

Re: drill press advice

#21

if you think that is grand......lathe and grinder

Bill Tindall, E.TN.

I have, for historical reasons, a 3-phase lathe, for which I added a VFD to run it. So, then I bought a 3 phase grinder. I can grind tools at 0-3600 rpm. Now that is sweet. I haven't added this capability to the drill press but it is under consideration.

Re: drill press advice

#22

Yeah... if I came across a grinder...

John in NM

I would pick one up in a minute, just 'cuz

My lathe has one of those variable pulley's, so that's not much of a pain.