Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

7 1/4" blade for tablesaw

Posts

Re: 7 1/4" blade for tablesaw

#26

Re: flat bottoms, splines and missed opportunity

Bruce, a MN Galoot

I don't have a chisel narrower than 1/8". I suppose I could make one, but... :D

Re: 7 1/4" blade for tablesaw

#28

Re: safety physics

Lars Parrington

warning

the following post contains lots of numbers which may only be useful to a theoretical woodworker in an imaginary shop. actual woodworkers are advised to stop reading and go build something.

introduction

i got curious about why these small blades seem safer, so i busted out some physics to see if i could find an answer. i looked at the difference in kinetic energy (KE) of various blades, as well as the KE of the motor's armature.

results

here is a list of blades and their relative KE's:

100% -- 10" full kerf

72% -- 10" thin kerf

22% -- 8-1/4" thin kerf

13% -- 7-1/4" thin kerf

however, the KE of the motor's armature is also significant, since it is directly coupled to the blade. a typical 1.5 hp would have a KE equal to ~75% that of the full kerf blade. if we look at the KE of the whole system (ignoring pulleys, belt, and arbor), the numbers change to:

100% -- 10" full kerf + motor

84% -- 10" thin kerf + motor

55% -- 8-1/4" thin kerf + motor

50% -- 7-1/4" thin kerf + motor

43% -- no blade, just motor

so how do these numbers translate into the severity of a kickback? lets look at the how fast a medium size maple board (3/4" x 4" x 48") would be thrown. here the first number is calculated from the KE of only the blade, and the second number is for blade + motor together:

53 mph -- 64 mph -- 10" full kerf

47 mph -- 61 mph -- 10" thin kerf

28 mph -- 50 mph -- 8-1/4" thin

22 mph -- 46 mph -- 7-1/4" thin

fine print

(1) i'm ignoring any electrical energy that is added to the system during the kickback. essentially i'm assuming that the kickback happens so quickly that the amount of electrical energy added would be insignificant.

(2) the first time i ran the calculation, i assumed the all of the blade's energy was transfered to the board, i.e. the blade ends up stopped. clearly this is not a good assumption. in reality the blade must retain enough energy so that it's teeth are moving at least as fast as the board. i reran the calculation so that the numbers shown here assume the teeth end up moving exactly as fast as the board.

(3) no slippage in the drive belt between motor and saw blade.

conclusion

i think the interesting result here is that the smaller two blades add a fairly insignificant amount of kinetic energy to the whole system, whereas either of the 10" blades approximately doubles the energy of the system. this does explain why the smaller blades might be safer, but i think there are probably also other factors involved, and i would be interested to head some more opinions on this subject.

Re: 7 1/4" blade for tablesaw

#29

Re: 3hp motor

Lars Parrington

i should mention that my conclusions in the last post would have been different if i had been considering a 3hp motor rather than 1.5hp. I couldn't find reliable data for a 3hp motor, but a cursory search indiates it's armature might have twice the moment of inertia of the 1.5hp motor, which translates to twice the KE.

In that case, the whole system already has so much KE, that the amount added by any blade (10" or smaller) would be fairly insignificant.

Re: 7 1/4" blade for tablesaw

#30

Re: safety physics

Bill Tindall, E.Tn.

I expect in reality that the motor is not coupled to the blade with 100% efficiency for a very short timed impulse like for a "catch". There will be some stretch in the belts and/or tighter seating in the pulley groove.

But more important is the observation that the teeth in these small blades don't throw things. There is vastly less force transferred to the wood by these blades when they are cutting or idling in the kerf. They don't seem to want to grab the wood an pull it into the teeth. This observation is probably a result of tooth size.

Re: 7 1/4" blade for tablesaw

#31

How we try to do in the mitten when cold....

roger lance

I think about winter

when I was with her

and the snow was falling down.

Warmed by the fire

I love being by her

when there's no one else around.

Re: 7 1/4" blade for tablesaw

#32

Re: 7 1/4" blade for tablesaw

Lars Parrington

well, i figured out why my 7-1/4" blade was making rough cuts. i had made a zero clearance insert with splitter for it back in the summer sometime, but hadn't used it again until very recently. since then, the insert had shrunk, which caused the sawblade to rub on one side and widen it's slot in the insert. the result was a misalignment of the blade and the splitter.

without the custom insert, the 7-1/4" blade cuts a lot smoother, though it's still nothing to write home about. i've got the 8-1/4" CMT on order, and made up a batch of new inserts out of baltic birch. they are tightly fit to the hole in the saw, which i suppose will cause me trouble when the humidity rises.

what do you guys make inserts out of? the slots in my plywood inserts seem to widen over time, presumably from expansion/contraction of the plywood. i thought about using some 1/4" acrylic for its dimensional stability, but decided it might fail in an explosive fashion should the blade tried to eat a scrap of wood.

Re: 7 1/4" blade for tablesaw

#33

Re: 7 1/4" blade for tablesaw

John M in Mid Mich

I use MDF. Have not had a problem with swelling/shrinking. My slots tend to widen as a result of the jump my blades takes when I start the motor. 3 hp Jet, don't know if this is same for other saws. Wish it was a soft-start motor (and while I'm wishing - wish it had an electric brake).

Re: 7 1/4" blade for tablesaw

#34

Re: 7 1/4" blade for tablesaw

Bill Tindall, E.Tn.

If an ultimately smooth cut is essential you will need to use a blade with little side clearance for ripping such as the Forest, and others(and pay the price in $, and more rapid dulling) or use a multitooth cut off blade for end grain cuts.

I make inserts out of what ever is handy- acrylic, nylon, UHMW, plywood, etc.I screw set screws into the bottom for jack screws for leveling. The slots gets chewed on, fact of life.

Re: 7 1/4" blade for tablesaw

#35

Re: 7 1/4" blade for tablesaw

Kelly Craig

I stop by counter top fabricators and buy sink cut-outs made of Corian or composites by other names. One cut out gives me several inserts and none of them seem to care horribly much about humidity.

Re: 7 1/4" blade for tablesaw

#36

Re: corian

Lars Parrington

interesting idea. i assume it comes thin enough and is easily cut with a tablesaw? my saw takes ~1/2" thick insert.

Re: 7 1/4" blade for tablesaw

#37

Re: corian

Kelly Craig

I use the composite sink cut out material for inserts on my Unisaw. I have just enough room to install [four] screws over the tabs for leveling.

I'm heading off for the weekend, but I'll try to remember to measure a piece. On a wild guess, it's at or near 1/2". If so, you may not have to add the height screws. It a smidgen too thick, a course belt on a sander would make short work of thinning it.

Here is a quote from a search on the web:

"Thickness and weight of a solid surface countertop - Solid surface countertops come in a wide range of thicknesses and weights. Much of a solid surface countertops durability and lifespan depends on the thickness and weight, so take extra care in making your decision. There are three standard thicknesses available: quarter-inch, half-inch, and three-fourths of an inch.

Re: 7 1/4" blade for tablesaw

#38

Re: corian

Lars Parrington

thanks. sounds like a useful material to have around in general. i suppose if it's easy to cut on a table saw, then the initial thickness is not too critical anyway.

i actually make my inserts out of 3/4" plywood since that's what i usually have scraps of. i just cut 1/4" rebates on the underside to make it fit. i also have to cut a notch in the middle where the saw's arbor would hit if i were to raise the blade all the way.

my saw is an old delta too, but a contractors saw. well, at it's core anyway. it seems to be expanding to fill all the available space around it. it has 2 craftsman cast iron table extensions as well as a plywood extension wing, and i just finished adding two maple outfeed tables. it also has a unifence with a digital readout, and a homemade dust shroud that encloses most of the arbor assembly.

Re: 7 1/4" blade for tablesaw

#39

Re: corian

Kelly Craig

I have a Merlin splitter, so have to cut notches in the end, as well as grind reliefs on the back side to allow the arbor to tip without it or the splitter mount pushing the plate out.

My first saw was a Delta contractors saw. I was able to afford a Unisaw, so went that route. I believe my contractors saw could have been turned into something just short of a Rolls, but hey, I like toys. Had I kept the contractor saw, like you, I would have added a Unifence and larger tables, or extensions. Too, I would have installed a Merlin splitter, or, better yet, the Riving knife add-on, as well as an Excalibur dust extractor-guard and a 3hp motor. Finally, I'd enclose the base and add dust pick-up). It was a damn excellent machine.