Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

How To Flatten A 12" Jointer Table?

Posts

How To Flatten A 12" Jointer Table?

#1

How To Flatten A 12" Jointer Table?

Derek Arita

I have a 12" Mini Max jointer/planer that has a top that is not as flat as I'd like. In places it's out .010. Anyways, it seems like a big job to flatten the top, as I've never had to have it done on any other machine I have. I/ve heard that I can take the machine to a machine shop and have it done.

How do I find a good machine shop that can do it? Do I remove both tables and take them in? How do they flatten the top? By the way, I'm in the Sacramento, CA area.

Re: How To Flatten A 12" Jointer Table?

#2

Re: Machining caution

Ralph Lipeles

If one side is good, you should only have the shop true up the bad one. Make sure that they support it the some way as it is supported in the jointer so that it will not distort when reinstalled and tightened in the jointer.

Ralph Lipeles

Re: How To Flatten A 12" Jointer Table?

#3

Kneale Brownson

It's WOOD.  0.010 is meaningless in wood


Re: How To Flatten A 12" Jointer Table?

#4

Re: It's WOOD.  0.010 is meaningless in wood

Derek Arita

That may be, but it gives me a gap when gluing up two boards longer than a couple of feet. I have an 8" jointer that is flat and it works great, but I'm trying to make this j/p do it all. If I can get the j/p surfaces flat, I think it will work fine. Besides, I'm picky about my machines and their tolerances.

Re: How To Flatten A 12" Jointer Table?

#5

Shim stock ??.....

roger lance

could this jointer table be shimmed with brass shim stock to bring it to level ??

Re: How To Flatten A 12" Jointer Table?

#6

Re: glue gap

Kenneth Kimura

Derek, a glue gap wouldn't be caused from either in feed or out feed table being a hundreds off dead flat. Check that tables are co planer and if that's ok experiment with your feed technique. All machines have their quirks. Your 8" jointer has longer tables than the mini max so your feed pressure will be different. Your initial query on machining is a slippery slope. At some point you'll realize your throwing money in a black hole.

Re: How To Flatten A 12" Jointer Table?

#7

What does Mini Max say?


Re: How To Flatten A 12" Jointer Table?

#8

How is it supported?

John in NM

I'm not familiar with the machine. If the table is in effect twisted, you may be able to adjust it out - you'd be surprised how those things can flex over distance.

I'd agree that the problem sounds a lot like beds that are not co-planar, but to some degree you can have the same effect with both.

Re: How To Flatten A 12" Jointer Table?

#9

Re: How To Flatten A 12" Jointer Table?

Robin Corell in Atascadero CA

It sounds like you might have set up your knives level with the outfeed table in an effort to eliminate snipe. If so this is incorrect and will lead to problems such as you are describing. A small amount of snipe is esintial to getting flat boards off of a jointer. I usually set my knives flush to the out feed table and then drop the outfeed table 005"-010".

Haveing a low spot of .010" shouldn't cause noticable problems in a jointer or planer. My planer has a .030 low spot and it has absolutely no effect on the flatness of the boards it produces.

Robin

Re: How To Flatten A 12" Jointer Table?

#10

Re: glue gap

Paul Vander Woude

I think .010 inch on a jointer table might cause gaps in a joint. It seems possible to me that that kind of an error, over, say, a 6 foot long board, with multiple passes, could cause a leading or trailing edge of the board to be significantly curved.

Re: How To Flatten A 12" Jointer Table?

#11

Re: How To Flatten A 12" Jointer Table?

Barry

I'm no expert in solving jointer problems, but have had some experience in dealing with my own machines. I seriously doubt that your solution will be found in attempts to flatten the outfeed table, especially when it is out only .010. Many instruction books will tell you to set the cutterhead knives level with the outfeed table, when in actual practice, the machine will work much better with the outfeed table slightly lower than the cutterhead. Jointers can be quite finicky and every machine is different with its own peculiarities. Try changing the set-up before you start machining away at the outfeed table. Your only result might be a slightly thinner outfeed table and wallet.

Re: How To Flatten A 12" Jointer Table?

#12

Re: How To Flatten A 12" Jointer Table?

Derek Arita

Thanks for all your input. I have had the machine professionally adjusted at the advice of MM, with their reference to the adjuster. In the end, he said he did the best he could, but the tables are both cupped, so that will always have an effect on the workpiece. I bought the machine new from MM as a floor model, at a reduced price, so I felt obligated to not make a big deal about this. Had I paid full pop, that would have been different.

At any rate, I'm still happy to have a 12"j/p. It's just that...I've had less expensive jointers who's tables were nearly dead flat. I expected this higher end machine would be at least as flat...but it's not, so I'll deal with it, in order to have the capacity. Again, thanks for all your input.

Re: How To Flatten A 12" Jointer Table?

#13

Re: How To Flatten A 12" Jointer Table?

Dick Coers

Plenty of advice given, but there surely must be a sweet spot for edge work. Find it, and lay some marks on the table. The cup shouldn't be so critical for face jointing, so you may be able to get by. I consider knowing the quirks of the machine is part of machine woodworking. If not, it's going to take a pretty big machine shop that has a blanchard grinder big enough, good luck.

Re: How To Flatten A 12" Jointer Table?

#14

Re: How To Flatten A 12" Jointer Table?

del schisler

i would belive the company would want it right ever tho you got a marked down on the price, i wouldn't feal bad telling them i want it like it is sopose to be. why take it at the way it is?? get it as it should be. It isn't going to cost them to have it right, if you hadn't bought it someone else would have and i bet they would have it fixed, my 2 cents