Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

My Rocking Chair--LONG

Posts

My Rocking Chair--LONG

#1

My Rocking Chair--LONG

James Fox

I usually hang out (lurk???) on the turning side of WC and occasionally post photos of my turnings, but I also enjoy doing flat stuff. This is the latest of my ventures into the flat side.

It’s one of those things that most of us have on “the list.” In May I finally got the chance (with a bit—LOT—of encouragement from my wife). I spent a couple of weeks at Andy Chidwick’s School of Fine Woodworking in Stevensville, MT building this one. Then there was another month-or-so completing the sculpting, sanding, and applying the finish.

There are at least a dozen or more courses out there that will teach you to build a “Maloof-Style rocker.” Some diverge to one degree or another from Sam’s design, others stay pretty much to his original. I picked Andy’s school because I could drive there from where I live near Seattle and bring back the rocker instead of shipping it, cost, and comments by other students of his.

The rocker is made from figured maple with walnut accents. The walnut is laminated into the rockers, back-slats, and ends of the headrest. The plugs covering the screw holes are also walnut. The finish is a mixture of oils with a final coat of wax. It’s a VERY comfortable chair.

After bringing the chair home, I was sanding on it in my driveway when an unfamiliar car drove by several times with the driver glancing at what I was doing. A bit later a neighbor and the driver came down to where I was working. The stranger was visiting from California, recognized the design of the chair I was working on and asked if I knew who Sam Maloof was. Turns out he is a docent at Sam Maloof’s house (now a museum) in California. He has since sent me a poster from the museum signed by the guys in Sam’s shop. It shows one of Sam’s rockers—they are still being built there by the guys in his shop. Small world.

James Fox


Re: My Rocking Chair--LONG

#2

Re: My Rocking Chair--LONG

MikeH1

That is a beautiful rocker. It's unfortunate though that there are so many folks out there that give no thought to making money teaching people how to make something someone else designed and spend their life building. You are correct that the three 'boys' are still building his pieces full time. There are also a whole batch of people making 'Sam Maloof' style rockers for sale for far less than what the Maloof company charges, ethical? I say no but that's just my opinion. Personally, I think anyone that is making a living copying someone elses work has some real honesty issues. There is even a discussion of this on the latest Fine woodworking Shop Talk podcast, number 15 I think.

Re: My Rocking Chair--LONG

#3

Re: My Rocking Chair--LONG

Larry in nw ohio

James That is one beautiful chair, the style and the wood. How long did it take to build and what kind of wood did you use, it looks very familiar? Larry

Re: My Rocking Chair--LONG

#4

Re: My Rocking Chair--LONG

James Fox

Thank you--the wood is figured maple with walnut accents. Time??? Rough guess is about 150 hours.

James

Re: My Rocking Chair--LONG

#5

Magnificent!


Re: My Rocking Chair--LONG

#6

That Chair Rocks!

Thomas Skaggs, Foothills of Mount Level

Looks like you paid attention in class. The chair is stunning. I have had the plasure of sitting in a Maloof rocker and I'm sure yours feels just as comfy. It's a beauty!

T.

Re: My Rocking Chair--LONG

#7

Please return....often

Bill Tindall

That's one gorgeous chair and a delight to look at. Post some of your other work.

I trust you recorded the admirer's name and email. You should get a personal tour of the museum when you visit it some day.

Re: My Rocking Chair--LONG

#8

Re: My Rocking Chair--LONG

Joseph Mulherin, sr

That is exactly like the rocking chairs I am building for my 10 family members....various sizes available in plans.

If you want to get the plans from Hal Taylor go to his website: Rocking chair University.com.

Plans cost only $35 for the basic plans, and the BBHT seat drilling plans are another $35.

I have both and the first chair came out marvelous....it does sit and rock well

Re: My Rocking Chair--LONG

#9

Re: My Rocking Chair--LONG

Joseph Mulherin, sr

There is one very difference in Maloof's chair and Taylor's....the back slats are not glued in the Taylor chair, they are installed using parafin wax so they move with the back when sitting....both front to back and side to side.

Hal Taylor gave Sam one of his chairs at a seminar in Atlanta and Sam said it was of the most comfortable chairs he had sat in ever.

Re: My Rocking Chair--LONG

#10

Re: My Rocking Chair--LONG

Jesse Cloud

Beautiful chair. The sculpting is great - you really have a good eye for form.

BTW, I don't see a darned thing wrong with making Sam's chairs. When he was alive, Sam was very giving, sharing details of how the chair is made. I think its wise to make a close copy of the original for your first chair, and then start to personalize it on later chairs. I am glad there are people out there keeping the tradition alive. My 2 cents.

Re: My Rocking Chair--LONG

#11

Beautiful chair....great story....

roger lance

and on the list.

Re: My Rocking Chair--LONG

#12

Re: My Rocking Chair--LONG

Yonak

James, those curves and twists are awesome. It's a beautiful sight to behold.

Re: My Rocking Chair--LONG

#13

Re: My Rocking Chair--LONG

Philip Duffy

GLORIOUS! Philip

Re: My Rocking Chair--LONG

#14

Thanks to all

James Fox

Now that I've "recovered" from this one :D I can start thinking about the next...walnut??? cherry??? mesquite???

James

Re: My Rocking Chair--LONG

#15

Re: Thanks to all

Joseph Mulherin, sr

Hello, James, tomorrow morning I am driving down to Aguanga, CA to a timber place to buy some ALDER to start making my 10 chairs for the family members.

My first chair came out rather well and I kept it for myself, but shall do some changes in the construction methods to achieve a little better construction technique...or just the way I work.

Alder is a soft hardwood, and I am placing oak laminate underneath the rockers for the wear spot. Poplar is going to be used for the accent line in the rockers, and the back braces accents.

Re: My Rocking Chair--LONG

#16

Re: Thanks to all

Joseph Mulherin, sr

Drove and drove until I finally stumbled on the correct road to the place.

Rob Durfos, the owner, had selected out 6 boards of 8"x2"x8ft...extremely clear of any knots or cuts or breaks. Loaded them up and drove home to my shop where I shall begin laying out the patterns on the boards and start cutting on the band saw. Laminations are going to be 1/8" thick which I shall use to glue together along with the poplar and oak for the rockers. Then they will be used to make the back braces.

Now, the seats will be three boards glued up with, I think, using bisquits for alignment and strength.

I am hoping to get almost two chairs out of these boards. Intend on trying to use tung oil for the initial covering, then maybe some Deft...if I can find any... and maybe just a wax for the final finish. I want the Alder beauty to show thru forever.... no more stains for me.

Re: My Rocking Chair--LONG

#17

Re: Thanks to all

Joseph Mulherin, sr

Laid out the patterns for the chair legs and arms. Got two chairs out of just 2 boards.

Another two boards got me the chair seats cut and bisquited and glued up, and still have another 2 1/2 boards to cut and get the lamination pieces...need 24 for rockers and 14 for back slats. Have to purchase some more poplar and oak too for the rockers and braces. This next week will be busy in my shop cutting and glueing up everything. Am going to be using the dado blade to scoop out the seats like Charles Neil showed, then band saw out the legs and arm from the other boards already laid out. Then use 1/2 router to roundover the edge3s where necessary, the change the router bit to a 3/4" round over to finish the round overs. Headrests still have to be cut and glued up in same grain pattern as the seats....vertical...

in a coopering fashion to get the roundness asked for in the headrests

Thought...with the other two board I might be able to get a third chair legs and arms out of them as well as the seat, and will be using the cutouts from the band sawing to cut the lams.....will see what happens. Later, Joe

Re: My Rocking Chair--LONG

#18

Re: Thanks to all

Joseph Mulherin, sr

Today I cut out the legs and arms on three chairs. I was correct in my calculations of possibly getting three chairs out of 60BF. Hal Taylor said each chair would take 40bf, well my layout outdid his I guess.

Still have enough wood left over to cut out the 76 lams needed for the three chairs. And the cutoff pieces will allow me to cut and install the blocks for the curvature from the legs to the seats.

These three chairs are going to go to my daughter and the three granddaughters. Then I have to make a large chair and another medium chairs for the other two granddaughters. Next year I will make the four large chairs for #1 son and three grandsons.

Hal made a "reading chair" back in 1995 to have when he was reading to his children. Each arm was made into a seat similar to the chair seat and the curvature back braces also. Have a picture of him reading to his three kids in that chair.

I thoroughly enjoy making these chairs for the family members....give me something to do in my retirement years and keeps me busy. So, three chairs before Xmas sounds good.

More later..... wish I had the knowledge of how to post pics to this website. ..had them earlier but lost everything when I had a compute4r crash.

Re: My Rocking Chair--LONG

#19

Re: Thanks to all

Joseph Mulherin, sr

OK, got all three chairs cut out on the band saw...only lost two blades. Laid out the seat patterns with a small center punch so I can see where to go to when I start grinding and sanding the curvatures.

Now have to setup the table saw and use the 8" dado blade to scoop out the center of the seats...just like Charles Neil shows on YouTube...."in the workshop" is the title to type in.

New carbide router bits haven't arrived yet, but then I can do the round overs on all of the legs and arm pieces.. ... 1/2" first, then change to 3/4". Also bought some rasp bits to use in forming the curvatures

on seat/leg attachments, and the rockers when I get them laminated and glued up and attached to the legs.

3 days of good workshop time for me, but have to go to the VA a couple times this week so I think I shall wait for next week to continue with the work on the chairs.

Re: My Rocking Chair--LONG

#20

Having fun

Merle

Joe, it sounds like you are really having a great time making these chairs. You seem able to do more in a day than I do in a week. You might inspire me to make a chair someday when my current list gets whittled down. Keep up the good work!

Re: My Rocking Chair--LONG

#21

Re: Having fun

Joseph Mulherin, sr

Thank you, Merle, yes I am having a great time doing what I love in making things for the family.

And, Sir, if you too wish to make the chair O am making go to :www.rockuniversity.com and buy Hal Taylor plans for $70 for the book, the plan patterns(5 chairs included), and the BBHT board with the hole pattern to use to drill the holes into the seat and headboard for the back braces.

I finished up band sawing the legs & arms out this morning...like I said and only lost two 1/4" blades.

Moved the Shopsmith into place and am going to setup the sheet metal/plywood extension table and

scoop out the three seats on Wednesday, getting ready to use the grinder and sanding discs.

If you wish to see how Hal Taylor does the chairs go to YouTube and type in "Hal Taylor rocking chair" in the upper opening website page.

I have already done three chairs earlier in the year getting ready to do these chairs....which I want to be PERFECT!!! My working ethics and work techniques differ somewhat from others....but that is how I am...and do not make too many mistakes(I hope).