Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Working with really rich pine?

Posts

Working with really rich pine?

#1

Working with really rich pine?

Keith Newton

I mentioned a while back that I had a project coming up that I will be building a desk, using the lumber from a former AR Champion Loblolly Pine. The client"s father owned the land, and beetles killed the tree.

I have been slow roasting the wood to set the pitch. But I'm wondering about finishing. I would suppose shellac would be the best sealer coat, or is there something else a bit harder, more suitable for a desk top?

I've used plenty of pine for construction purposes, but not for fine furniture.

Also, there are some areas which are really beyond just having really rich late-wood, but there is a weird block pattern across the early wood, giving the appearance of snake wood. I'm thinking about using some of that in the small doors on the little console which rest on the back of the top.

I wish I could have gotten in on sawing this tree up, I would have ripped it with my chainsaw then put the halves on my woodmizer, and had some QS or edge grain planks, where two would have made the top. But the best now are only 5".

Any pitfalls you can share would be appreciated.

Re: Working with really rich pine?

#2

Re: Working with really rich pine?

Howard Acheson

The problem with using pine--particularly lob-lolly pine--is its softness. It will be very susceptible to damage from anyone using a ball point pen when writing on paper on the surface. The writing will be "telegraphed" into the wood.

There is really no finish that will harden the surface of the wood with the exception of a pour-on epoxy which has other problems associated with it.

A couple of suggestion:

o Use a harder wood for the top

o Buy a blotter pad to protect the surface

o Avoid a soft finish like poly or oil based varnish.

Re: Working with really rich pine?

#3

Thanks Howard

Keith Newton

I have already selected some deep dark red edge-grain for the top. Yet I might do a test to see if I can do a epoxy saturation in the soft rings.

Re: Working with really rich pine?

#4

Re: Working with really rich pine?

Robin Corell in Atascadero CA

A few years ago I made a pair of cabinets out of sugar pine. it was a special tree that was struck by lightning and about 8" of the 24" wide boards were blue with a nice sprinkling of some worm holes. I used all the rustic parts for one cabinet and all the unstained and sound parts for abother.

For the blue cabinet I used Jasco tung oil and for the other I carved the panels and then used jasco tung oil tinted with oil paint. I built a rich finish buy using 0 coats each tinted a slightly different color. The cabinet finished with the straight jasco ting oil had 3 or 4 coats and it had a nice sheen and a wonderful warm amber tone to it.

Unfortunately Jasco tung oil was a victim of bain Capital and is no longer available. I am close to getting similar results with a blend of McCloskeys spar varnish, polimerized tung oil, a dash or turp and a bit of japan drier. It isn't quite as amber as I would like.

not sure if yu are familliar with sugar pine but it is uniqe among the pines because there is almost no difference between the early and late wood, which makes it nice to carve. It is soft so it would need a blotter or a piece of glass for the top or used in a design that is intended to be rustic.

here is a pic of the more rustic of the two cabinets.

Robin


Re: Working with really rich pine?

#5

Re: Working with really rich pine?

Larry in nw ohio

WOW Robin that is a great looking cabinent and a good use of what some people would call junk lumber. Good Job. Larry

Re: Working with really rich pine?

#6

Re: Working with really rich pine?

Keith Newton

Hum, You are making me wish I had gotten some of the bug-stained wood, but the beetles that killed this one leave a lot larger holes, and I'm afraid it was a bit more decayed. I couldn't even find any usable knots in the pile, they were all too large.

Back in the seventies, I could get Sugar Pine here at a decent price, and you are right, it is a sweet wood to work with. It so fun making ribbons with my planes, I used them for Xmas wrapping.

Thanks for sharing that, nice work.

Re: Working with really rich pine?

#7

Re: Working with really rich pine?

Dave Bair, Eaton Rapids, MI

An option is to use a piece of glass for the "top coat". It'll show the wood but block surface damage. It could be too pricey, though. It depends on how much you have into the project.

Re: Working with really rich pine?

#8

Re: Working with really rich pine?

Keith Newton

I'll probably leave that up to the customer, if they want it, but the edge-grain that I plan to use for the top, is not as bad as the big broad bands on plain sawn pine. When I think about it, sometimes I see old edge-grain pine floors, where they used this rich lumber, and they look great, even after a hundred years.

Probably when they were installed, they may not have even had a finish. Back then, I think the women or their maids would get down with a scrub brush on a regular basis with soap and water.

Re: Working with really rich pine?

#9

Nice cabinet!