Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Weight on a floor

Posts

Weight on a floor

#1

Weight on a floor

Dustmaker Mike

howdy all. well I have slowly been moving into my new shop area. As I move along in the next year or so I am going to be replacing a few of my tools for bigger and better. When I retire in a few years I want all my tools paid for so I won't have to worry about them. So here is my question. My shop floor is set up like this.

2X10 x 16 long on 16" centers

3/4 4x8 OSB T&G

1/4 Masonite with a flooring on top.

If I replace the Jointer with an 8 or 12 inch version that weighs in at say 800 pounds will I need to strengthen the floor under it if it does not sit on the floor joist but in between them?

I am just looking right now and will be buying in the next year but want to get ahead of it if I need to beef up the flooring.

Thanks

Re: Weight on a floor

#2

Re: Weight on a floor

John in NM

If you're concerned about the give in the flooring, I think you have nothing to worry about. If you don't end up with a clear answer, remind me next Thursday when I'm home and I'll look it up in the book - there's a table or two concerning floor sheathing vs. load as I remember.

The joists themselves do seem like kind of a long span for that load however - might want to check it with a load calculator. That would be considered a live load, though I've always had my doubts about where the line between the two lies when it comes to heavy machines - they often stay put for years.

If you can add a post below the location, that would be the most simple solution to the span question, if if does turn out to need a bit of help.

Re: Weight on a floor

#3

Re: Weight on a floor

Bill Houghton, Sebastopol, CA

Your immediate question was the strength of the floor membrane (the 3/4" ply subfloor and whatever strength the flooring itself gives). One solution to that would be a "pad" of 2x stock, long enough to span between joists, under the machine. This would locally make the floor thicker. If you're taller than the average height to which the machine was designed, it may be easier on your back, too.

Re: Weight on a floor

#4

The answer is YES and NO......

Barry Irby

The answer is somewhat complex. To calculate the strength of the floor we would also need to know the grade and species of lumber.

As rule of thumb, yellow pine is substantially stiffer than spruce. In my building days I considered yellow pine to adequate for a 15' span on sixteen inch centers. Even that was pretty loose. It took into account the Dead Load (weight of the structure) and a live load of something like 40 pounds per square foot. It turns out that a refrigerator or a water bed are too heavy for most floors. An 800 pound jointer certainly would be, since it has a fairly small foot print. OTOH, my gut instinct is that there is no chance it will punch through the floor. If the jointer is near mid span and not over a beam or near a support wall below it will probably cause the floor to sag over time. I would want a support below.

The idea of putting a pad of two-by material under it and spreading the load over two or three joists would be good. If you don't want a post below, you could double two or three joists. If you have the room, 2 x 12's would be better. Better still would be Microlams or some sort of engineered timbers.

Re: Weight on a floor

#5

Re: Weight on a floor

roger lance

Mike....find a local contractor that you trust to come over some evening and look at your situation....so much of the answer depends on what you have and how it was built....if you have an accessible area under the floor, then ideally you could place a beam or two with proper support of those beams (cement footings and steel coluums to carry the beam)....now you are looking at an effective span of 8' in the case of one beam....which should be adequate in terms of the joists....OSB is better than wet cardboard but I would not have much faith in it for load carrying ability....undoubtedly you will park a heavy tablesaw in the middle of your shop and you will probably use some mobile bases under your other heavy machines like that jointer....planer...etc....and one night while you're moving things around you'll test that OSB....I'd do it right now and spend some bucks on beefing up that floor so I didn't ever have to worry about it....with planning, this could be an opportunity to incorporate some dust control lines and electrical lines under the floor....etc...etc....but it all depends on what you have....we can only speculate....get that contractor's opinion.

Re: Weight on a floor

#6

Re: Weight on a floor

Keith Newton

Mike your cheapest and easiest solution to your question, is to get under there and add some blocking / bridging between joist. When they go in there tight, they tie a bunch of them together, so a point load on one is shared by several each way.

Then again, doing a drop girder beam under the joist is another good way to strengthen a floor span.

But I would start with the blocking first. Even if it is only between a couple of joist right under the tool base. That is a lot of weight for just PB and masonite.

If the joist spans start to sag from this dead load, it probably will take a while, but you can always come back later, and bring them back up with bottle jacks and a new footing later. I helped some friends level their floors in a 90 year old house a few years back. The rooms were big, and floors were down 1.5" out in the middle. Dishes would rattle when the kids ran, but they were straight and solid after I got through.

Re: Weight on a floor

#7

Your joists are undersized *LINK*

Lee Schierer McKean, PA

According to what I know, your joists are undersized for a 16' span. The nominal height of the joist dictate the length of span allowed for a normal floor loading on 16" centers. 2 x 10, should only span about 10 feet. They should be at least 2 x 12's or on 12" centers for that span. Here's a link to a chart that might help.


Floor Joist Allowable span

Re: Weight on a floor

#8

Re: Your joists are undersized

Joseph Mulherin Sr.

Mike, are you able to get to under the floor and work on the joists? If so, I would recommend doubling up on the joists which will be having the extra weight...liquid nails and thru screws..... and maybe a deadman post underneath them for extra insurance.

Re: Weight on a floor

#9

Re: Your joists are undersized

Larry in nw ohio

Mike As said in another post, putting a deadman post under the joist may held and I think I would do a couple of them on each one while you can still get at them. IIRC I read that you can get at them yet. I`d get the cement post things that is put under a post to hold up the deadman post. I do not know what they are called, if I find out I`ll post it. But I would do two of them under a 16` joist just to be on the safe side and while I can still get at them. I think I`d do that under where you are going to put the heavy machinery and maybe every other one the rest of the room. You never know where you may move things. Good Luck and have fun in your new building. Larry

Re: Weight on a floor

#10

Re: Your joists are undersized

John Verkamp

Or,

position a cross beam made home made consisting of 2 2X10's sandwiching a 10" strip of 3/4 ply, glued and screwed together. Center the beam at the 8' mark. Position footings and posts or blocks at each end and the middle. This assumes you have enough clearance to add the beam at least a couple of inches above dirt. Add 2 sets of cross blocking at the 4' and 12' marks. Should significantly stiffen the floor.

Re: Weight on a floor

#11

The building inspector

Dustmaker Mike

Never said a thing about them being undersized. So now I will have to watch and see if I need to make a knee wall under it.

Re: Weight on a floor

#12

Thanks

Dustmaker Mike

The floor under the shop is poured concrete hand floated. The crawl space is about 5'6" when I get the new tools I will strengthen the floor under them as needed. I store all my lawn equipment under it.

Re: Weight on a floor

#13

Re: Thanks

Larry in nw ohio

Mike I think I would keep a very close eye on the floor when you put heavy equipment in there. Also where ever you place the heavier stuff and have it set where you pretty well want it, I would put a single brace under it and maybe clamp it with a clamp so it`s temporary and mark it at the top so you can watch it if it starts to sink. Good luck Mike. Larry

Re: Weight on a floor

#14

tool placement and posts

Joseph Mulherin, Sr.

Mike, when you get the heavy tools and decide where you want them situated

and you say the floor underneath the shop is poured concrete, I would go to

the Home Depot or Lowes and purchase those cement post holders and some

framing metal clipps they sell for houses; Anchor the cement posts holders to

the concrete floor with some angle clips And the 4" deadman post anchored to

the floor joists with screws. Space several out as needed and to allow you yard

equipment room to maneuver around. You can always remove the screws and

clips if you decide to move the equipment and reinstall at another place.

Re: Weight on a floor

#15

Re: Thanks

AZ in Colorado Springs

Since you have a cement floor in the crawlspace you ought to measure the height (now) between the floor the joists in several places. Write the measurements on the joists. Then you can measure later and see how the floor is changing -- where, how fast, etc.