Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

glue out at the corners

Posts

glue out at the corners

#1

glue out at the corners

eliot d

I've posted before about this, but the plot thickens a bit. I have to glue up a box roughly 1 x 1 x 2 feet, which has mitered edges all around, BEFORE (for a reason of no interest to anyone else) applying any finish to it. I posted here while still thinking that I could apply finish first; and the best advice was to spline the edges, which I did, and use wax paper and some right-angled clamping blocks. But now, on bare wood, I'm worried that I won't have sufficient access to the outside edges ( don't care about inside) to wipe off the glue squeeze-out as it appears. The wood is furniture grade birch plywood; and I want to minimize any glue seeping into the outside surface so that when finishing is applied after glue up, blotching, etc, will be minimized. I plan on doing one edge at a time. Is there some cool way to clamp it up and still have access to the entire edge for wiping off the glue? Can I wax the wood first along the edges? Will it come off easily?

Re: glue out at the corners

#2

prevention is the answer

Bill Tindall

I don't mean this to be harsh....but learn to apply the correct amount of glue. If more than a tiny bead squeezes out too much has been applied. Application with a brush helps to get an optimum amount on each surface. I buy "acid brushes" (metal handle and 1/2" stiff black bristles) for these tasks.

Re: glue out at the corners

#3

Re: glue out at the corners

Thomas Skaggs, Foothills of Mount Level

Do not wipe off the glue that squeezes out. Use only sufficient glue to minimize the squeeze-out. Let the squeze-out harden and then scrape it off. If you wipe it, you will smear it into the wood fibers around the corners.

T.

Re: glue out at the corners

#4

Re: glue out at the corners

Grant Wilkinson

I've used masking tape and Waxilit with good results.

Re: glue out at the corners

#5

Re: glue out at the corners

Bruce, a MN Galoot

if you use liquid hide glue, you get a relatively longer assembly time and clean-up can be done with a toothbrush and water.

Re: glue out at the corners

#6

Re: glue out at the corners

eliot d

Well, there may still be a trouble: the wood is furniture-grade plywood, so sanding or scraping could be a problem. I can't risk going through a layer of plywood. I certainly see your point for wood other than plywood.

Re: glue out at the corners

#7

Re: glue out at the corners

eliot d

Do you mean real, old fashioned rabbit skin stuff that you make in a pot? Or do you mean one of the new liquid hide glues that comes in a bottle? In either case, are you saying that these can be gotten rid of with a toothbrush in such a way that later application of finish will be totally uniform? If you mean hide glue in a bottle, then this appears to be the safest solution to my problem. Can you suggest a brand? ( I have heard, though. that the new hide glues in a bottle aren't so good.)

Re: glue out at the corners

#8

Re: glue out at the corners

Dick Coers

Do you really scrub plywood with a toothbrush and water? I don't use water anywhere on a furniture build, but I think todays plywood would be even worse. You would get swelling and fibers raised up everywhere. How would you sand that back smooth on the inside of the joint? If any staining goes on after a water wash, the stain will soak in differently in that area. I sweat a lot in the summer and have to constantly be aware of any drops that hit the wood. I've had dark spots show up in the staining if I miss it.

On miters, I like to brush on a thin coat of Titebond and let it sit for a short while. It's not dry to the touch, but it has soaked in a bit. Then I brush on a very thin coat and clamp. The first coat acts like a primer and fills the pores just a little. I forget if you are adding other reinforcement to the joint. A glued only miter is never very strong, but even worse in plywood. There just isn't enough long grain to hold.

Re: glue out at the corners

#9

Liquid Hide Glue *LINK*

doug f, san clemente, ca

Eliot - I've always had real good results from this stuff.

Doug


http://www.oldbrownglue.com/

Re: glue out at the corners

#10

Re: glue out at the corners

Bruce, a MN Galoot

In a mitered corner like this, I'd use a spline. And yes, I've cleaned up plywood with water. Just like any glue, you don't slather it on. Clean up isn't that much fun.

Re: glue out at the corners

#11

Re: glue out at the corners

roger lance

First, you can pre-finish these parts....just place some blue tape over the miters to protect them from the finish....easy to do....after the finishing is over, remove the tape and maybe a little lite sanding might be needed on the miter to get clear wood....then glue in a spline on one piece per corner and let cure for an hour (this helps keep your sanity) and glue up the piece.

Second, you can attach a strip of blue tape on the corners, inside and out, to catch the squeeze out.

Third, having followed the good advise to limit the amount of glue used so squeeze out is minimal, you can let that squeeze out sit for about 20 - 30 minutes and it will form a rubbery mass that can literally be lifted in one long string right off the piece....but this takes some experience to know when the glue is in this state.

Plywood will take some sanding....just not a lot of sanding.

Re: glue out at the corners

#12

Re: glue out at the corners

John McGaw

I have used the blue tape 'trick' for years for all sorts of glue-ups where cleaning after the fact would be troublesome. Works fine on the inside of virtually any joint (finger, miter, dovetail, dado, MM&T, etc) and on the outside of many with the limiting factor being how meticulous you are when applying the tape. I've resorted to applying tape to the outside of finger joints and then cutting out the interfering parts with a craft knife. The only problem with this is that tape and glue might mix at any fuzzy edge making removal more difficult than it should be.

Re: glue out at the corners

#13

Re: glue out at the corners

Jerry Gibbs

remember with ordinary pva glue you can remove the clamps after 1-2 hours. don't stress the joint and you can access the rubbery squeeze out.

Re: glue out at the corners

#14

Re: glue out at the corners

mdclor

You indicated that you will be using splines. You can rout a small V grove on both sides of the splines that will act as reservoirs for any excess glue. Of course you will need to avoid using more glue that the V's can hold.

Re: glue out at the corners

#15

Re: glue out at the corners

eliot d

Dick, are you saying that you are worried about the strength of the glue up along all mitered edges through 3/4 inch birch plywood for a box that is 1 x 1 x 2 feet ? I'm not talking about a small picture frame here. If you really think it's a problem, I could reinforce everything inside, where I don't care about looks. This project is an audio speaker enclosure.

Re: glue out at the corners

#16

Re: glue out at the corners

eliot d

As I said, I have to glue up before applying finish. I do like the idea of applying some kind of tape along the joint to , hopefully, catch the squeeze out. My concern with this approach is that glue may seep under the tape. I don't know that regular blue tape would be so hot. Perhaps, though, there is a preferred tape just for this purpose. ( I suppose your point is that blue tape IS the preferred tape.) If you are suggesting that I let the glue squeeze out onto bare wood and solve the problem by getting rid of it at that "chewing gum" stage, I don't like it because the glue will still stain into the wood before it begins to harden. So , if I understand you correctly, you are advocating tape AND "chewing gum". Do I have it right? (My wife, who is not a wood worker, likes your first idea: finish first. I like it too. but there are some logistical problems involving another person, time, travel, etc.)

Re: glue out at the corners

#17

Re: glue out at the corners

roger lance

I would not have said these things if they were not so.....get some experience of your own your way....I'll point one other thing out to you, IF you have cut a proper dado into each mitered end that runs the whole length or nearly the whole length of your mitered corners, you only have to get the proper amount of glue into these dadoes to receive the spline....if each piece is glued to a proper spline and the joint is held tight while the glue sets, you will have a glued up box with no squeeze out at all.

Re: glue out at the corners

#18

Re: glue out at the corners

David Yoho

Your best solution would be to finish first. However, if for some reason it's not possible in this case, blue painter's tape and liquid hide glue is the next best approach.

I found out not all blue tape is equal. I look for the 3M brand with an orange colored core. Carefully applied along the mitered edges, it will provide acceptable protection. Any hide glue squeeze-out will dry hard and is easy to remove with a sharp chisel and a little hot water wipe. If a little does stay in the wood it tends to hide better under finish than yellow glue.

Re: glue out at the corners

#19

Re: glue out at the corners *LINK*

Dick Coers

Speaker boxes were built like tanks in the old days, don't know about todays work. But knowing what you are building will help me give you some advice. Before glue up, have the plywood face up. Butt the miter points tightly together, then pull a single piece of blue tape all along the miter. Carefully turn them over, add the glue, then fold up the two pieces using the tape like a hinge. No way glue will make it out to the outside. Here's a link showing basically what i said. They turned the tape 90 degrees from my technique. Test your tape on a veneer scrap to see if it will lift veneer fibers.


miter glue up tips

Re: glue out at the corners

#20

Re: glue out at the corners

eliot d

I know the tape trick for gluing up boxes, but I always thought it was for smallish boxes. And I have cut splines in all the miters. Will the method still work if there are splines? I can imagine laying it out as described, applying glue, folding it together without the splines, and then sliding the splines in from the ends. (I remember cutting the grooves and splines so that the spline fit is fairly loose. So I may get away with it.) You do see that if I put the splines in first, then I won't be able to fold the sides together.

Re: glue out at the corners

#21

Re: glue out at the corners

eliot d

Sounds great! Didn't mean to doubt your approach. Just worried. These are for a relative, so I don't want to screw it up.

Re: glue out at the corners

#22

Re: glue out at the corners

roger lance

From above, you say the splines are loose....you want snug....not tight....not loose....if you try this method....again, my advise is to glue the spline into one side only....let the glue dry....then proceed with the final glue-up....glue control is a rarely discussed topic and most of us were taught incorrectly by Norm to use too much glue with glue coming out of a joint only to be wiped away with a wet rag....excessive glue is of no benefit to the joint....getting the right amount of glue on the right surface makes for strong joints and minimal mess....make some test pieces with dado, spline, and mitered sides and see how this will work. In addition, I would remind you of a mortice/tenon technique where material is removed from the shoulder of the tenon to insure that the edge of the tenon shoulder makes perfect contact with the side of the mortice board....you get visually a real tight appearance of the final joint with this technique.....some of the material of the mitered edge could also be pared back toward the spline/dado with the edge of the miters now going together tightly.

Re: glue out at the corners

#23

Re: glue out at the corners

eliot d

I could easily remake to splines so there's a tighter fit. What I had in mind for the splines was merely to keep the mitered boards from slipping during glue up -- not so much to hold them together. But what you say seems better. ( I recently made this really neat jig for my table saw that allows cutting repeated, identical long strips that are to thin for safe cutting near the fence.) Thanks for you help.

Re: glue out at the corners

#24

Re: glue out at the corners

roger lance

Since you will be depending on the strength of the spline to hold the joint together, you do not want a thin spline....I assume your mitered stock is 3/4" thick, so have at minimum 1/4" or 5/16" thick splines....and a plywood spline would work fine....if you use regular wood for the splines, make sure the grain of the spline is running cross ways to the miters....do not make the splines by ripping them with the grain....easy to break a board (spline) with the grain....hard to break a board against the grain.

Re: glue out at the corners

#25

Ellis Walentine

Mitered plywood

Ellis Walentine

Eliot, sorry I'm late to this discussion, but here's my 2¢ anyhow. It is possible to make these joints accurately enough, but even if you do, you'll need to leave the corners dangerously sharp in order to keep from sanding through the thin (~.025") face veneer. Speakers always get beat up, and those edges are going to be very vulnerable, not to mention sharp. What I do is this: First, I miter the pieces as perfectly as I can, then I use biscuits to align the parts accurately during glue-up. To keep any glue squeeze-out from penetrating the veneer, I rub a coat of wax on the plywood in the neighborhood of the joints. You can easily remove the wax before finishing with some solvent. After glue-up, I rout a small rabbet along all the edges and glue in a thin strip of matching wood. It could be anywhere from 1/8" to 1/4" square; just make sure it is a little larger in section than the rabbet, so it sits a little proud. You can trim the excess later with a sharp block plane. Miter the strips at the corners, then glue them into the rabbets using short pieces of masking tape stretched across the strips to apply the clamping pressure. The pieces of tape should be side by side, so the entire strip is covered. Do the top and bottom four edges first and then cut pieces to fit in the other four rabbets. When the glue is dry, pane them flush or almost flush and finish them off with a piece of sandpaper wrapped around a solid block of wood or MDF. You want the block to be hard and flat. Then, you can chamfer the edges or round them gently or with a round-over bit. A slight round-over will hold the finish much better than a sharp edge.

I have used this technique many many times with great success.

Ellis