Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

1/3 hp motor question

Posts

1/3 hp motor question

#1

1/3 hp motor question

Charlie Lenz

I'll be honest right away and say that I picked up a used Dayton 1/3 hp furnace blower motor from the local heating guys junk pile. It looks in nice condition, I brought it home and wired it up to about a 3ft long 18 gauge three wire cord ( white, black, green ) Pluged it into a power strip, turned it on and it hummed, so I shut it off. Then I turned the arbor, and turned it on and it ran. So I tried it from a dead stop and it ran, the next time it didn't without turning the arbor. When I shut the power off the motor spins down and I hear a click which I know is normal, but it has kind of a grumble before it clicks. Anyway, anyone have any ideas as to if it might be an easy fix or not ? A good cleaning ? Or take it to a motor shop ? Here are the specs for the motor, Belt Drive Motor, Split-Phase, Open Dripproof, 1/3 HP, 1725 RPM, Number of Speeds 1, 115 Volts, 6.6 Full Load Amps, 48Y NEMA Frame, Service Factor 1.35, 60 Hz, Cradle Mount, Ball Bearings, Auto Thermal Protection, Rotation CW/CCW, Ambient 40 C, Insulation Class B, Shaft Diameter 1/2 In, Shaft Length 1 1/2 In, Body Dia 5 5/8 In.

Re: 1/3 hp motor question

#2

Re: 1/3 hp motor question

Bill Turpin in WNC mountains

If it has a capacitor replace the cap. Clean the non-shaft end with air. Clean the centrifical switch at that same end.

Re: 1/3 hp motor question

#3

Re: 1/3 hp motor question

Jason Waters

Charlie,

Have you worked on motors before? A good disassembly, cleaning, new bearings, maybe a capacitor, and she should work great. as long as the armature and field is good (was it permanent or not?).

I'd guess a capacitor problem, or the start disc thing (centrifugal switch) isn't contacting good, causing the start capacitor to not engage.

1/3 hp isn't too expensive new, but a motor shop could charge a lot for a small motor, and usually isn't worth it unless it's a special frame or 3/4 hp (and usually not then) or larger in my opinion. Some of them might put a test capacitor in and if that's it, sell you one, without charging much, but I kinda doubt it, those kind of places are hardly around anymore.

I have found Dayton motors to be great motors. I have a 1.5 hp I cleaned, painted, new bearings, on my bandsaw. It was $40, plus about $15 for bearings, and $6 in paint........Not too shabby.

I'd call around to a motor shop, see if they would check the capacitor for you....

Re: 1/3 hp motor question

#4

Re: 1/3 hp motor question *LINK*

Bob Entwisle in NJ

Hi Chuck,

Here's a link to some motor info which, coupled with some investigation on your part, may help you figure out whats going on.

I'd see about opening it up a bit to take a gander at the centrifugal switch contacts and mechanism, I've seen screws come a little loose and cause unreliable operation. I didn't search out that particular motor, but you may be able to find detailed specs for the motor online. If there is a starting capacitor that is switched in by the centrifugal switch, then as long as the switch mechanism is operating freely, the Cap would be the next place to look.

Hope this helps

Bob in NJ


http://www.allaboutcircuits.com/vol_2/chpt_13/9.html

Re: 1/3 hp motor question

#5

Split phase motors don't have capacitors

Bill Houghton, Sebastopol, CA

Sounds like the centrifugal switch is sticking. I've never repaired one of those, but I imagine it's a matter of cleaning things up.

Re: 1/3 hp motor question

#6

Re: Split phase motors don't have capacitors

Charlie Lenz

I haven't worked on motors alot, I've pulled a couple apart over the years , but really don't know much about them. I would say that this isn't a Capacitor start motor, there isn't a Capacitor attached to it. This motor is for a belt driven blower that sit's ontop of the blower, and not inside the blower. The motors that sit inside the blower usually have a start Capacitor attached to the exterior of the blower. I'm hopeing that it's just a dirty Centrifical switch. Maybe I'll try diging into it a little tommarow and see how dirty or lose the contact may be. Are there any tricks to takeing it apart and geting it back together that I should know ? If all else fails, a couple blocks down the road there is a electric motor shop that has been there for many years.

Re: 1/3 hp motor question

#7

Re: 1/3 hp motor question ( Bob )

Charlie Lenz

Thanks for the article, from what I can tell in the article is that it is a Resistance split-phase motor induction motor. All the other technical data goes over my head. I'm more of a mechanical guy than an electrical guy.

Re: 1/3 hp motor question

#8

Re: 1/3 hp motor question ( Bob )

Bob Entwisle in NJ

Hi Chuck,

Ok, so now you know there's no capacitor involved.

As to taking it apart and investigating, just take it slow and careful is how I do it.

Keep your eye out for thin thrust washers and such as you pull the end cover and bearing off of the shaft. The centrifugal switch mechanism may have a spring or two associated with it, so keep an eye on those too.

The centrifugal switch, when the motor is off, should be in a position that the contacts are closed, once the motor revs up partway to speed, the centrifugal switch snaps open, disconnecting the starting winding while the motor is running.

There are weights on the switch that when the motor gets going, are thrown outward by the centrifugal force and cause the contacts to open. with the motor apart you should be able to move the switch parts by poking around at them to observe the operation of the switch.

Bob in NJ

Re: 1/3 hp motor question

#9

Re: 1/3 hp motor question ( Bob )

Bob Entwisle in NJ

Chuck,

I didn't mean for all the technical phase angle electrical stuff that was alos in the link. I mostly thought the link had a couple of clear diagrams of cap start, cap run, resistance etc. to help figure out what type of motor you were dealing with.

For the most part, if there's no capacitor involved, and the motor windings are good, then it more often than not boils down to a mechanical problem, bearings, centrifugal switch mechanism etc.

Bob in NJ

Re: 1/3 hp motor question

#10

Re: 1/3 hp motor question ( Bob )

Russ

I have pretty good luck by using the airhose and blow it out real good sometimes it's just debris in the contacts and the airhose will get it.

Re: 1/3 hp motor question

#11

Re: Well I opened it up tonight

Charlie Lenz

It didn't look too bad as far as dust, dirt and grime. So anyway, I played around with the centrifugal and gave it a shot of silicone spray being careful not to get it on everything, and leaving an excess to get flung around. Then fastened to the bottom of the cover was the contact, or what I think look like old fashioned car points. So being the old car enthusiast that I was years ago I had a points file that I gently filed the points with. Put it all back together, oiled the oil resevors a little and pluged it in, hit the switch and it worked for about 20 on/offs. Went out and put my tools away, came back, tried it again, and back to the same ol hum. At this point I think that there is enough resistance in a bearing or both at one spot that it doesn't have enough to giddyup to go. Or is it possible that the armature is dirty ? ( wishfull thinking I'm sure )

Re: 1/3 hp motor question

#12

Re: 1/3 hp motor question ( Russ )

Charlie Lenz

I think that blowing it out with the air hose is going to be next before hauling it off for an estimate at the electric motor shop. But anyway, thats enough for tonight, tomarrow is another day.

Re: 1/3 hp motor question

#13

Re: I opened it up again this morning

Charlie Lenz

This time I pulled the cover on the shaft side and pulled the Armature out. I noticed that there aren't any bearings in this motor, just bushings. I looked over the Armature and decided to clean it up a little with some steel wool, it didn't look too bad but decided it was worth a shot. Then I cleaned up the fan blades and the inside of the end cover and put it all back together. So far it seems to be working good. If it gives me anymore trouble about the only thing that I could think of that it would be is that the contact points are wore out, everything else looks pretty darn good. As I mentioned in the first post, the motor really does look in pretty good shape. and not all that old.


img

Re: 1/3 hp motor question

#14

Re: I opened it up again this morning

Larry in nw ohio

Charlie I don`t want to sound all smartalicy, but take a look on your plate and it says BRG Sleeve, right there it tells you that it is a non bearing motor, if you didn`t notice that. Good luck with it. Larry

Re: 1/3 hp motor question

#15

Re: I opened it up again this morning

Neal in San Jose

Just a couple of thoughts. First the good news: It is rated for continuous duty (DUTY: cont) and has a service factor of 1.35 (SF: 1.35) so it is a pretty good motor. The bad news is the bearings. Did you notice the instruction to oil once a year? What do you think the chances that happened are? My house was built in '63 with the original furnace still in place. I've lived there 15 years and have never oiled the bearings and I'd be willing to bet the previous owner didn't either.

Re: 1/3 hp motor question

#16

Re: They can have caps *LINK*

Bill Turpin in WNC mountains

They can have capacitors see link below


WW Grainger

Re: 1/3 hp motor question

#17

Jim DeLaney, Austintown, Ohio

Re: I opened it up again this morning

Jim DeLaney, Austintown, Ohio

I'd say that your experience is pretty much typical - unless you have the furnace professionally serviced every so often. I know the fan motor for my oil furnace gets lubed once a year by my service tech, but I've only lived here for eight years, and the furnace is 23 years old. From the condition it was in when I first had it serviced, I'd bet that was its first oiling, too.

Good news for the sleeve type bearings, though, is that it's them that wears, and not the steel motor shaft. The bushings are cheap and replaceable. Even my local Home Depot carries them!

Re: 1/3 hp motor question

#18

Re: The bearings are replable BUT

Larry Clinton At Frankfort, (Central) Indiana

many years ago I worked in a motor repair shop bench. Yes the bearings are fairly easy to replace but normally they must be reamed to open them up to the size of the shaft. I have probably replaced several hundred and had to ream them all for the motor to properly function. A line reamer is the best method (it aligns the reamer using a cone shaped sleeve that fits over the reamer shaft and slides into one end while you are reaming the other end) a stub reamer will work but you take a chance of making the bearing oversize before the motor shaft will rotate easily when assembled - due to the bearing ID being misaligned with the centerline of the motor. The oil impregnated bearings will run for years as noted before failure even without proper lube - with proper lube they will last practically forever.

Re: 1/3 hp motor question

#19

Re: I opened it up again this morning

Charlie Lenz

Yeah I finally noticed the marking on the label BRG as Sleeve, I'm kind of slow and I'm not a electric motor expert obviously, but no offense taken. The motor actually had oil in the reservours, but the previous owner probably filled them as a last ditch attempt at an easy fix before rep[laceing the motor. But asa I said, the motor I think looks in pretty good shape, nothing really looks worn, or any burn marks from overheating. I should of mentioned in my first post what I'm going to do with the motor. A year or so ago I bought a small 8 inch PowerKraft ( Montgomery Wards ) table saw that was missing a motor. http://vintagemachinery.org/photoindex/detail.aspx?id=11829 I cleaned it up and repainted it and put it up for sale. I never got the price that I wanted for it so I decided to get a small motor and turn it into a 8" disc sander in the hobby shop. I have done this before with another small 8 inch table saw ( AMT brand ) and it worked out well and was kind of nice to have, but I sold that last fall.

Re: 1/3 hp motor question

#21

Re: Jason thats really interesting...

Charlie Lenz

and you may have stumbled into something worth checking out. Apparently the B in the 6K778B must stand for bushings. The 6K778B seems to be really hard to find and that maybe the 6K778 which has bearings has takein the 6K778B spot. I might have to check and see if the 6K778B case can be fitted with bearings without breaking the bank.

Re: 1/3 hp motor question

#22

Re: Jason thats really interesting...

Larry in nw ohio

Charlie I don`t think a roller bearing would fit,but you might find a needle bearing. I seem to remember my father and I did something like that many, many years ago on a Go-Kart we built. IIRC we did it on a Centrifical Clutch that had a Brass bearing in it, and we new that would not last very long, so we found a Needle bearing to replace it. That`ll be a nice motor for something. Good Luck Larry

Re: 1/3 hp motor question

#23

Re: Thats really interesting ( Larry )

Charlie Lenz

I was thinking the needle bearing thing at first too Larry, but by the looks of the motor case I'm thinking that the motor cases might be the same and that ball type bearings would fit. I e:mailed Grainger lastnight and probably won't get an answer till Monday or Tuesday. Speaking of go-carts, I use to have a Yamaha cart with the 100cc two stroke motor, that machine was a pretty wild ride on a Grand Prix style race course. I can't imagine a ride in the newer 125cc water cooled shifter carts they have nowdays.

Re: 1/3 hp motor question

#24

Re: Thats really interesting ( Larry )

Larry in nw ohio

Charlie I built 3-4 carts with my Father and over time I thought about getting an old motorcycle engine and transmission and mounting that on a cart. But as time went by I started getting into bikes, we built a little scooter in school shop. Dad and I took 1" black and an old blacksmith portable firebox on wheels, I forget what they called them, and we heated and bent it around untill we got it lookin like a scooter frame.Then I took it to school and welded everything else on it and put a motor and centrifical clutch on it and believe it or not I drove it home after I finished. I really surprized the teacher when most everyone else was making saw horses and such. Larry

Re: 1/3 hp motor question

#25

Re: 1/3 hp Dayton motor ( Grainger )

Charlie Lenz

Well I got an e:mail from Grainger this morning telling me that the 6K778B motor that I have should have bearings in it, and that the motor might be mislabeled. So I called them and talked to one of their motor specialists. He told me that the older motors had bushings, ok. Then I asked him how hard it would be to get the parts to switch it over to bearings, I was told next to impossible, one reason being that the motor manufacturer isn't interested in selling parts. NICE !