Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

JET Bandsaw Burned Out...electrical question

Posts

JET Bandsaw Burned Out...electrical question

#1

JET Bandsaw Burned Out...electrical question

Ed in NY

I was resawing some 8/4 oak yesterday, same wood I was inquiring about a couple of weeks ago when it bowed as soon as it was resawn, and something I've done many times before, when all of a sudden the bandsaw popped a circuit breaker. It's a JET 14" closed stand bandsaw with a 1HP motor and brand new 3/4" Timberwolf bandsaw blade. I reset the breaker and it started right up and I began to cut again and then the breaker popped again. Then I smelled smoke. I opened the cabinet and the motor was burning hot. So I removed the wood from the blade, reset the breaker and the saw ran fine. I let it run for a minute or so just to be sure. When I came back about 2 hours later it didn't start and the motor was still too hot to touch. I removed the motor and one whole side of the casing was brown! Couldn't believe it. I wasn't bogging down the motor at all and as soon as I saw it slowing a bit, I backed off. I have no idea how this happened. So now I have to order a new motor (for about $250). My question is would I get better performance in the future if I wire the new motor for 220v instead of 115V? I was never really impressed with the cutting performance of this saw but I'm hoping a new motor at 220v will make it somewhat better.

Re: JET Bandsaw Burned Out...electrical question

#2

Re: JET Bandsaw Burned Out...electrical question

Larry Clinton At Frankfort, (Central) Indiana

If your wiring is correct (large enough to carry the current required for the 1 hp motor without excessive voltage drop), there is absolutely no difference in running a motor at 120V versus 240 Volt. With proper wiring they put out exactly the same power (Watts). The advantage to using 240V is that you can carry twice the horsepower using the same size wire. IE: A 1 HP motor may use 8 amp on 120V the same motor running on 240 V will draw only 4 amp. However the wattage is exactly the same (960 watt). A normal circuit using #12 wire will carry 20 Amp for 50 foot with very little voltage drop so to answer your question NO it would not help. Your options may be to look at motor suppliers like Grainger to see if you can find a motor with a larger HP rating that will fit in your application.

Re: JET Bandsaw Burned Out...electrical question

#3

Re: JET Bandsaw Burned Out...electrical question

Ed in NY

Thanks for the reply Larry, I guess it would be a waste to convert it to 220 then, so I will skip that. I'm thinking getting a bigger, maybe 2HP motor at Grainger along with getting a mount put on it would be cost prohibitive. I might was well spend a few hundred bucks more and jsut get a bigger, better saw...

Re: JET Bandsaw Burned Out...electrical question

#4

Alternative

Mark Mandell - Gone Round In New Jersey

Find a motor shop in your area, and take the motor to them to ask what cooked. It may also be repairable, although if the windings are toast it won't be worth it.

Re: JET Bandsaw Burned Out...electrical question

#5

Re: Alternative

Ed in NY

I'm pretty sure it was the windings. The capacitor clicks on but the motor doesn't turn. Also, where I live (Long Island) is pathetic for finding shops to fix/repair anything. Plenty of nail salons and cell phone stores but not a tool or woodworking shop anywhere. It's really sad.

Re: JET Bandsaw Burned Out...electrical question

#6

Re: Alternative

Al Stokka - Cambridge, Iowa

Ed,

I used Google and the search specification "electric motor repair Long Island, New York".

A bunch of 'em popped up...even showed a handy dandy map with pushpins and everything.

Now, if someone knows someone near Cambridge who'd be interested in replacing a couple of sheets of steel roofing on my barn and a few ripped shingles on a 1½ story house....

Al

Re: JET Bandsaw Burned Out...electrical question

#7

Re: Alternative

Ed in NY

Did the same search Al and came with one...one motor repair shop in an area that serves 5 million people...pathetic. I'd probably have to take out a mortgage to pay for a rewound motor.

Re: JET Bandsaw Burned Out...electrical question

#8

Motor might just come with the right mount

John in NM

You will at least be able to determine the bolt spacing of the mount of potential replacements and see if it's the same or if you can work with it. Most tools use 3rd party motors so the mounts tend to be less of a problem than you'd think.

Of course, if you prefer to go with the bigger saw, by all means go ahead :D :D :D

In general, I've found blade choice to make a huge difference, but I also much prefer fully cast saws like the old Powermatics and General's Canadian made ones. They're just more rigid and seem to have no weird tracking problems. But you pay through the nose for that, so maybe its worth the effort to tune up a Chinese C-frame saw (I actually did use one of those that was really nice once too, it was an old, old Jet 16").

Another place to look at your blade is for chip clearing - your "underpowered" feel of the motor may be that the blade is bogged down clearing the dust. Go with a bigger gullet blade and a slower feed, and you may find a 1 HP to be plenty powerfull.

Re: JET Bandsaw Burned Out...electrical question

#9

Re: JET Bandsaw Burned Out...electrical question

AZ in Colorado Springs

I'm thinking have an electrician look at the motor to see why it got cooked ... so the same thing doesn't happen to your new motor. Some problem with the fan or blocking cooling air/ventilation? Don't want to spend the bucks to get operating again only to have the problem recur.

Re: JET Bandsaw Burned Out...electrical question

#10

Re: JET Bandsaw Burned Out...electrical question

Brian in SLO

I have the same exact saw and had the same exact occurance.

I took the motor to the nearest electric motor shop and they agreed it was toast.

They then found me a replacement 2HP motor with proper mounts. It fit right in!

I can check when I get home what make and model number I got and you should be able to look it up on the internet and pick one up. It was a few hundred bucks but far less than a new saw and now plenty powerful enough for resawing.

BTW, I only use a 1/2" blade for resawing.

Re: JET Bandsaw Burned Out...electrical question

#11

Re: JET Bandsaw Burned Out...electrical question

Ed in NY

Thanks Brian, at least I'm not alone. I actually already ordered a new one, it was only $215 plus $40 shipping, so it wasn't too bad. Maybe I will try the 1/2" blade when I get the new motor and see if it makes any difference.

Re: JET Bandsaw Burned Out...electrical question

#12

Re: JET Bandsaw Burned Out...electrical question

Ed in NY

I'm guessing it was a combination of the motor working too hard, the wood being too hard and thick. It's a TEFC motor and designed for the machine but I will leave the cabinet open next time to get some airflow around the motor.

Re: JET Bandsaw Burned Out...electrical question

#13

Theory

Mark Mandell - Gone Round In New Jersey

Worst thing for a TEFC motor is to assume it's completely dust-proof. They can get clogged with sawdust, especially the centrifugal switch and the fan housing, and you wind up with a stuck start phase or a hot motor from not enough air movement through the fan shroud. Not much of an issue in exposed motors, but I blow out my cab saw TEFC motor fairly often. Just something to remember that the owner's manual doesn't mention.

Re: JET Bandsaw Burned Out...electrical question

#14

Re: Theory

Ed in NY

Thanks Mark, the old motor is sitting on the floor of my shop, I'll hit it with some compressed air tonight and see how much dust comes out of it. I have to say the inside of the cabinet of that saw reamins pretty clean but I'm thinking that could also mean it's so tight air doesn't circulate well.

Re: JET Bandsaw Burned Out...electrical question

#15

Re: JET Bandsaw upper axle assembly problem

Charlie Lenz

I know this has nothing to do with your motor problem, but the way it sounds I have the same saw as well ( cream colored ). I had a 3/4 blade in it and forgot to release the tension on it when I last used it in the fall. When spring rolled around I went to use it and it made a loud knocking noise. The axle assembly was hitting the spokes in the wheel. Moral of the story, detention your blade at the end of the day. When I bought the new axle assembly I noticed that it had been beefed up.

Re: JET Bandsaw Burned Out...electrical question

#16

Re: JET Bandsaw upper axle assembly problem

Ed in NY

Thanks for the tip Charlie. I actually went out and got one of those quick relase arm assemblies years and years ago so I rarely forget to detention or retention the blade. The ball on the end of that arm is hard to miss!

Re: JET Bandsaw Burned Out...electrical question

#17

Re: JET Bandsaw upper axle assembly problem

Charlie Lenz

The quick release would really be nice to have, and I've wanted one for sometime allready, but they were pretty pricey when they first came out. I don't use my bandsaw much, and times are tough here so I do without. But after haveing the assembly fail and haveing to buy the part, it's doubtfull that I'll forget to release the tension again. Maybe someday I'll be able to afford one, then I won't have to turn the tension knob so much.

Re: JET Bandsaw Burned Out...electrical question

#18

Re: JET Bandsaw Burned Out...electrical question

Harry Ludke

Same thing happened to me when I first got my Jet 14" band saw. Was resawing some Cherry with a new Timberwolf resaw blade. I was not forcing the wood past the blade. I was on my 4th or 5th cut when I began to get an electrical smell, the motor was toast. Fortunately I was still in the warranty period and when I called Jet to tell them what happened they replaced the motor, no questions asked. That was years ago and I haven't had any problems sense.

Re: JET Bandsaw Burned Out...electrical question

#19

Re:Charlie

Larry in nw ohio

Charlie I read your last post and you say you turn your tension KNOB, Charlie if you have a knob instead of a crank, I would change that right away. That is what I did with my saw and it is so much quicker and easier that you would wish you would have thought of it sooner. Larry

Re: JET Bandsaw Burned Out...electrical question

#20

Re:Larry

Charlie Lenz

Your right, and I think I've seen a crank on a 14" bandsaw, can't remember if it was an owner mod, or a factory setup, but if I remember correctly it would have to have an eyebolt installed in the wheel cover to stabilize the rod.

Re: JET Bandsaw Burned Out...electrical question

#21

Re:Larry

Jason Waters

I made one for my Delta using 3/8 threaded rod, a handwheel and crank from grizzly, a little drilling and tapping.

Re: JET Bandsaw Burned Out...electrical question

#22

Re: JET Bandsaw Burned Out...electrical question

Jason Waters

Sounds like you got it solved with a new motor.

I rebuilt a 14" Delta last year and picked up a 1.5hp Dayton motor used for $40, which I put new bearings in, and cleaned up and painted.

If you bought a US made motor, I think you will find it will be better than the Chinese one that came on the saw. Probably better insulation class, service factor, etc.

Re: JET Bandsaw Burned Out...electrical question

#23

Re:Larry

Larry in nw ohio

Charlie As with what Jason did is just about what I did. Mine is an old Craftsman and all I needed to do is take a 3/4" rod and drill and tap a 3/8" hole in it and weld a horizontal bar and a verical handle and bingo I had a crank. The way it sounds that you might have most everything you would need to make something to make it easier to crank it up and down. Good Luck Charlie. Larry

Re: JET Bandsaw Burned Out...electrical question

#24

Re: JET Bandsaw Burned Out...electrical question

Art Silva

I have not read all of the entries yet, but this sounds like a bad Capacitor, a big problem with motors from Taiwan or China.

Re: JET Bandsaw Burned Out...electrical question

#25

Re: JET Bandsaw Burned Out...electrical question

Ed in NY

No, it's not the cap, the windings are fried.