Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

OT - Water hammer arrester

Posts

OT - Water hammer arrester

#1

OT - Water hammer arrester

Hoa in Alameda

We've experienced water hammer a lot recently, particularly when the sprinkler valves are switching. I wonder if I install a water hammer arrester where the faucet currently is, I can eliminate the hammering.

Please see the photo attached. The sprinkler valves are about 12 ft. from that location.

Thanks.


img

Re: OT - Water hammer arrester

#2

Re: OT - Water hammer arrestor

Barry Irby

I am not a plumber but I used to know one pretty well. I think the best place to put one is to put a vertical piece of pipe either on the line to the sprinkler valves or directly up from the incoming line. This could be as simple as a vertical piece of pipe about eight inches long with a cap on top. You can buy the devices as well, but I don't know if they work any better and they are significantly more expensive.

It is probably the sprinkler valves slamming shut that causes the hammer. The other question would be why has this started now? What changed? The principle is that the valves slam shut and the momentum of the water in the pipes causes them to buck and bang. Have the clamps come off the pipes somewhere and allow the pipe to move more than they used too? Have you changed the sprinkler valves to ones that slam shut faster? Is there a water hammer device or chamber in the system that has lost its charge of air and thus its cushion?

Does it never freeze in Alameda? That setup could not get through the first winter here.

Re: OT - Water hammer arrester

#3

Re: OT - Water hammer arrestor

Bill Turpin in WNC mountains

I would recommend that the hammer riser be longer, more like 18". Put in the short nipple where the word "To" the house is in your pic. Is the hammer in the house or out at the sprinkler valve? If it is outside, put the riser closer to the valves.

Re: OT - Water hammer arrester

#4

Re: OT - Water hammer arrester

Lee Schierer McKean, PA

The water hammer device should be placed as close to the valve or device producing the water hammer as possible. While a vertical piece of pipe filled with air may work initially, it will gradually lose air and become less effective. The captive air type never need recharging but will need to be sized for the pipe ther are to be installed in and the water pressure.

Lee

Re: OT - Water hammer arrester

#5

Re: OT - Water hammer arrester

Alan in Little Washington (NC)

In addition to adding an expansion chamber you might want to check the water pressure. Water hammer is typically worse with higher water pressure. If that is a regulator in the riser, maybe you need to check the pressure and adjust it.

Re: OT - Water hammer arrester

#6

Re: OT - Water hammer arrester

Joseph Mulherin

Hoa, I am a retired plumber and this is what I recommend: cut in a tee between the two tees listed and 90 out to a rubber diaphramed air hammer arrester which you can buy at a local plumbing supply.

Since the picture shows some sapace between the incoming and the house wall I would face the tee towaqrds the house. The arrestor I am speaking of is about 4" dia by 7" tall with a male thread on the tail.

Re: OT - Water hammer arrester

#7

Lee's right...

Mike in NC

Air chambers will only eventually lose their air and then you are back to square one. WHA's aren't that expensive - I have seen some that start about $10 for a size A and about $15 for a B, give or take a few dollars. Can't imagine you would need anything larger than a B. They are sized according to fixture units - not sure how fixture units would be figured with a sprinkler system.

I would be mindful about freeze protection as well.

Re: OT - Water hammer arrester

#8

Re: OT - Water hammer arrester

Galen Vetterick

I don't know if you mean the line marked "house" supplies the potable water to your house. How do you get by without a backflow preventor on the branch to your sprinklers? The run of tee would make a perfect injector to draw ground water or air back into your home from the sprinkler system if the heads do not shut off air tight. Even the hose connection on a branch this close to the main water flow could let contaminated water back into the line if the valve might not shut off tight.

I could see how you could get water hammer in the house if it is pulling air back in and even if it just brings air into your sprinkler line you would get a good hammer when the supply pressure returns to the sprinkler system.

Maybe that is not a union I see on the sprinkler line but hope maybe at least a check valve for only one direction of flow?

Re: OT - Water hammer arrester

#9

Re: OT - Water hammer arrester

Robin Corell in Atascadero CA

Hoa,

That little gizmo just above the main valve coming from the meter is a pressure regulator and they need periodic maintanance. What typically happens is that as they fail they stop regulating the pressure. If your water hammer problem is recent I would suspect the pressure ragulator has allowed the pressure in your whole house to get too high. Those little gizmoes arre expensive little suckers but they are rebuildable.

Most hardware stores will have a pressure guage that will screw on to a hose bib. I have my regulator set at 50psi. My main line pressure was 150psi and caused the mixing valve in the shower to crack in two. I was lucky because it could have caused a toilet valve to vail and flood my house.

Robin

Re: OT - Water hammer arrester

#10

Re: OT - Water hammer arrester

Fred Davis

Hoa , I did a lot of work on Alameda Island, if that is where you live and their Mechanical and Plumbing inspector would not have passed your current setup.

Since it is to late to have a short Air chamber on each supply line at each fixture in the house , do as Joseph suggests, but have a Plumber eliminate the extemporaneous fittings,

FredD

Re: OT - Water hammer arrester

#11

Thanks, folks.

Hoa in Alameda

Wow, there's so much info for me to digest.

The house is actually in Union City. For those who's not familiar with the SF East Bay area, it's a city along 880 Fwy, mid-point between Oakland (or Alameda where my office is) and San Jose. No, it's never freezing or snowing here.

The house was built in 1994, along with about 200 others. They must have passed inspection then.

I found a place a few feet from the sprinkler valves where I can installed an arrester. The pipe is underground, but there is an area that can be dug up. Per Robin's advice, I'll also get a pressure gauge to check if the pressure regulator needs to be replaced.

Some of you mentioned backflow prevention: there is a device at the valves. I think it is the backflow preventer. The hose bib does have a siphon breaker.

Something to do this weekend....

Thanks, folks.

-- Hoa

Re: OT - Water hammer arrester

#12

Re: Thanks, folks.

Larry in nw ohio

Hoa Take a look at the line that is going to the sprinklers, it looks to me that fitting on the bottom just above ground level is a union and then just above that looks to be a check valve. I don`t know what else it could be. Larry

Re: OT - Water hammer arrester

#13

Re: Thanks, folks.

Alex Grigoriev

I saw an arrestor (at Lowes?) sized for the garden hose thread, so you can attach it right next to the sprinkler pipe.