Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

More Tool chest pics

Posts

More Tool chest pics

#1

More Tool chest pics

Virgil Johnson

>I snapped this pic this morning while for the shop to reach working temp. I need to take a few more passes with a plane across the top edge of the front panel to make the gap even. It is still too tight now. This is a cross between a Kennedy and a Union Tool chest as they are the ones I have to measure. I need to saw the lid off at some point in the near future. I'm trying to think of ways to saw off the lid with minimal waste in the kerf. I have a 3" dia .040 carbide slitting saw but cringe at the thoughts of running it 20K RPM in my router on a shop made arbor.


img

Re: More Tool chest pics

#2

Re: More Tool chest pics

M. McNamee

>Have you thought about using one of the Whiteside slotting cutters? I use a single 1/16 inch 3 wing in the router table to saw off my box lids.

Re: More Tool chest pics

#3

Re: More Tool chest pics

Larry in NW Ohio

>Virgil First off HAPPY NEW YEAR. As for your chest, I think I would measure down to where you are going to make your cut. Then get your saw and measure fromthe edge of your saws fence to the edge of the blade. Take that measurement and add that to other measurement and clamp a fence there. then take your saw and run your saw against the fence, and do that all the way around. If I understood what you wanted to do, this should work. If that isn`t what you wanted to do, just ignore what I wrote. Good luck. Larry

Re: More Tool chest pics

#4

Alternative?

doug f, san clemente, ca

>Virgil - If it were my toolbox, and I so wish it were, I'd consider resawing it. My Woodslicer blade has a kerf of about .122 and with the bandsaw tuned up, would make short work of the top decapitation.

Just a thought.

Have fun with your project.

Doug

Re: More Tool chest pics

#5

Caution . . .

Pete in Holland, MI

>If your slitting saw is one designed for metal, it doesn't have any set to the teeth and will have a tendancy to bind, if not burn your kerf.

Re: More Tool chest pics

#6

Agree--My Method, Too

George@Colonel's Workshop-Havertown PA

>

Re: More Tool chest pics

#7

yep.

Virgil Johnson

>Its got a bit of side clearance but I'm afraid that any binding will shatter it. There is not much that scares in the shop me but this does.

Re: More Tool chest pics

#8

3 1/2"problem

Virgil Johnson

>My old school Powermatic will only resaw around 7". I'm leaning toward the Whiteside cutter mentioned earlier. I did not know such a cutter existed since I've never had to slice off a top as big as this. If I had allowed another 1/4" in the overall height I would not be concerned.

Re: More Tool chest pics

#9

thin blades

Grant in Iowa

>Go to a contractors supply store (maybe Homely Depot, or Lowe's too) and pick up a super thin kerf circular saw blade. The type used by framing contractors on circular saws is what I am thinking of. It is fine to use a 7 1/4" blade in your table saw. Find a carbide tipped one with lots of teeth and install that in your table saw. It's what we've used when milling cedar for strip canoes to minimize waste and they work fine.

If it were me, I'd put a layer of blue tape around the cut line first to help prevent tearout.

Make sure you insert shims in the slot after you make each cut. I'd set the blade just high enough to cut through your stock to achieve the best cut quality.

Regards,

Grant in Iowah

Re: More Tool chest pics

#10

Too late now

Bill Houghton, Sebastopol, CA

>but I've read recommmendations in some box articles to hot glue pieces inside the box at the lid/box joint, so that the lid and box will stay attached when run across the tablesaw, until you saw them out by hand.

Nice looking box - NICE looking box - by the way.

Re: More Tool chest pics

#11

Re: More Tool chest pics

David

>I'm not sure if this will help. I cut the lids off boxes on the table saw, thin kerf blade, raised a hair less than the thickness of the stock. Once all cuts are complete I go back with a new razor and cut the material that remains. I can control a small box top easily and cut it free with no damage, then just lightly sand the edges. On a larger top that may tend to swing free and break the last side, I'll tape the top on after inserting shims in the gap, i.e., cut one side free, insert shims and tape, repeat on next side.

Hope this helps and isn't too confusing.

DGW