Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Cabinet Crown Molding Advice

Posts

Cabinet Crown Molding Advice

#1

Cabinet Crown Molding Advice

matt in Richardson, TX

>I am putting the final touches on a kitchen renovation (that I substantially completed a year and a half ago :)) and I have come across a problem with the crown molding. I have designed a detail that is simple, but unique, with a three bead detail and flat crown separated by a frosted glass that I will light up with light rope. This will tie in another design element across the room that utilizes the back lighted frosted glass in our glassware cabinets.

The problem is that the ceiling is not level, and in the 9' run this crown is on, the ceiling is out 5/8". There is only a 6" gap (roughly) between the top of the cabinets and the ceiling, and I originally wanted to run the crown so that it touches the ceiling. However, that will cause the frosted glass to be uneven by 5/8" across the run. Any suggestions on how to make this work? I attached a picture of a rudimenatary mock up so you can see what I'm talking about.

Thanks,

Matt


img

Re: Cabinet Crown Molding Advice

#2

Corey Megal

Re: Cabinet Crown Molding Advice

Corey Megal

>Matt, cool design. You're going to have to scribe the crown to the ceiling. I would use a piece of ply in place of the glass, scribe the fit, then replace the ply with the glass.

Corey

Re: Cabinet Crown Molding Advice

#3

Re: Cabinet Crown Molding Advice

BILL White

>Corey nailed it. My vote too.

Bill

Re: Cabinet Crown Molding Advice

#4

Re: Cabinet Crown Molding Advice

Michael Wilkins

>Another tip here. Why not make the groove that the glass is sitting in deeper. Then have the glass cut to fit the wider end of the room and the other end can be loose in its groove. You can even shim the lower end with a fat bead of silicone caulk for the glass to ride in if there are issues with fitting the glass. By the way; neat design idea. Looks like something out of a magazine.

Re: Cabinet Crown Molding Advice

#5

Re: Cabinet Crown Molding Advice

matt in Richardson, TX

>If I scribe the actual crown molding, I'll run out of material on the top of the crown before the run is finished. And if I use the glass as the element to be scribed, the gap between the bottom on the crown and the top of the triple bead will not be uniform across the run. I think this might be a lose lose, unless I change the design. Maybe I can split the difference between the two and then neither will change by more than 5/16"?

Re: Cabinet Crown Molding Advice

#6

Re: Cabinet Crown Molding Advice

Kris Lasure

>Why not put a scribe molding on top of the crown. Could be as simple as putting on a 3/4" x 3/4" strip on top of the crown and scribe that piece to fit so you don't have to scribe your crown. You have definitely come up with a very creative design so I think you have the ability to work through this little hurdle.

Show us a picture when you're done!

kl

Re: Cabinet Crown Molding Advice

#7

Re: Cabinet Crown Molding Advice

Larry in NW Ohio

>Matt I don`t understand the full concept of your design so I hope you don`t take this idea as being really dumb. Could you take yout top and bottom pieces with the glass in and make the grooves deeper and if you need to put a piece of rubber or sponge rubber in the bottom piece to hold the glass up enough to close the gap at the top. I hopr this doesn`t sound to ridiculous. Larry in Ohio

Re: Cabinet Crown Molding Advice

#8

Re: Cabinet Crown Molding Advice

Ronald

>Sounds like this is the way to go, at least the easiest.

Re: Cabinet Crown Molding Advice

#9

That gets my vote as well,

John E in SC

>

Re: Cabinet Crown Molding Advice

#10

Re: Cabinet Crown Molding Advice

Mark Rakestraw

>I agree with Chris, use a scribe molding on top of the crown. I live in an old post and beam farmhouse and had 1.25" change in ceiling height in less than 5 feet. The scribe molding is basically a wedge shape, that leaves the contact point of the crown with the ceiling level. Part of that old house charm....you notice it, but it doesn't look bad. Given your figures it will only be noticable to you and any trim carpenter friends you happen to have.

Mark

Re: Cabinet Crown Molding Advice

#11

Re: Cabinet Crown Molding Advice

matt in Richardson, TX

>I agree (and kinda upset I couldn't come up with that). Sometimes you get so fixated on your design, that a solution involving adding something to your design doesn't even cross your mind. Thanks for all your input, I'll let you know how it turns out.