Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

I'm baffled, table saw cut problem.

Posts

I'm baffled, table saw cut problem.

#1

I'm baffled, table saw cut problem.

jeff

>Hi all

I have a problem here I can't figure out.

I cut a bunch of cherry today for some boxes.

This is a cross grain cut, on a jig, with the blade set to 45 degrees.

The pieces are between 3" and 5", from different boards.

Everyone of the cuts is not straight, but concave.

When I put a straight edge on the point of the 45, you can see a small gap in the center.

The boards are all flat and straight otherwise.

I've seen this when a board isn't straight and flat, or sits with a cup on it, but these are perfect.

Can anyone shed some light on this and how to correct it.

Jeff

Re: I'm baffled, table saw cut problem.

#2

Re: I'm baffled, table saw cut problem.

Rick Christopherson

>At first glance, your symptoms indicate that your miter slot is not parallel with the blade, and as a result, you are cutting across the arc of the blade. It seems hard to imagine the saw being far enough out of line for this symptom to be noticeable, but it will be most evident when beveling.

The other aspect that would magnify this problem is a low blade height. The lower the blade, the more into the arc the saw is operating. If you don't have the time to tune the saw in the middle of a project, simply raise the blade more and the symptom will be diminished.

Re: I'm baffled, table saw cut problem.

#3

Re: I'm baffled, table saw cut problem.

Robin Corell in Atascadero CA

>It is also possible for the blade to be parallel to the miter slot when at 90* and still be out of parallel when at 45* this is more problematic and the solution varies depending on if you have a contractor saw or a cabinet saw.

Robin

Re: I'm baffled, table saw cut problem.

#4

Re: I'm baffled, table saw cut problem.

Dick Coers

>Is your blade sharp? I would say that the blade is dull and is flexing or the wood is moving around because too much effort is going into the cutting. Try a different blade, or take a cut wide of the line, then take a really light cut to the line. Should help, good luck.

Re: I'm baffled, table saw cut problem.

#5

Re: I'm baffled, table saw cut problem.

Chuck in ND

>Why would you crosscut a board thats only 5 inches wide on a tablesaw ? You have alot better control of the board on a mitersaw, just make sure the blade is really sharp.

Re: I'm baffled, table saw cut problem.

#6

Re: I'm baffled, table saw cut problem.

Larry Marker

>I agree with the dull blade idea. Or maybe a cheap blade.

My first project in my first woodworking course was a walnut side table. I made the legs out of two pieces about 3/4 thick and 2.5 in wide with 45 deg bevels on one edge to make a miter joint. I ripped these on a Rockwell TS and they came out concave. The instructor was quite baffled, but after fooling around for a bit, he swapped the blade for a better quality (and sharper) blade and I recut the pieces and they came out perfect. I don't know if it was a dull blade or a blade that flexed excessively, but it was definitely blade related.

Larry

Re: I'm baffled, table saw cut problem.

#7

Lee Grindinger

I suspect the blade, but...,

Lee Grindinger

>You don't say whether the workpiece is on top of the laid over blade or above it but you may try making this cut from the other side of the blade. This could be either a blade wobble problem or it could be resulting from the force the blade exerts on the workpiece as the teeth start the cut and rear teeth exit the cut. Teeth tracks might reveal a lot, is there a nice consistent set of arcs in the cut? Or do they change direction? You might be changing the pressure on the workpiece as the blade changes it's pressure as well.

I'd suggest first trying the cut from the other side and seeing if the results are the same. If you get burn marks your blade is out of alignment and this is likely your problem. If the results are identical to what you're getting now it's a blade problem, either dull or cheap or damaged. If the problem vanishes it's quite possibly the way you're feeding the workpiece or the snugness of the jig in the mitre slot.

Lee

Re: I'm baffled, table saw cut problem.

#8

I'll test and try the suggestions today.

jeff

>The blade is a Forrest Woodworker.

I'll swap it for new one and also try a Chopmaster.

I'll get my dial indicator out and test the squareness.

Also, I'll try raising the blade some more.

As for the cut itself, it's smooth as silk with no cut marks.

I only get burning if I cut too slow.

I'll also try cutting from the other side.

Will have more info this afternoon.

Jeff

Re: I'm baffled, table saw cut problem.

#9

Re: I'll test and try the suggestions today.

pecker

>If all else fails, try making the cut 1/16" oversized, then trimming it a second time to the final dimension. There is a lot less force exerted on the 2nd cut from the blade. So if the blade is deflecting, or the stock is shifting as you push it during the first cut, there will be much less movement the 2nd go round.

I have this problem myself, as my blade is slightly out of parallel when tilted to 45 degrees.

Re: I'm baffled, table saw cut problem.

#10

Are you SURE your wood isn't cupped?

Phil Thien

>I've experienced that problem and it turned out the wood was slightly cupped. I know you say it is flat. But even slight variations in the flatness or thickness of a piece of wood will be obvious when making a bevel cut.

Re: I'm baffled, table saw cut problem.

#11

Since You're Testing. . ..

Mark Mandell - Gone Round In Jersey

>Since you said the workpiece is straight and flat, you might as well check your jig. If there's any vertical flex or lack of flatness there, it will translate to the cut as a curve especially if you put a bit more more down-force on the workpiece during the middle of the cut than you do at the start and finish of the cut. If the curve is compound, meaning curved across the cut length as well as across the bevel, I'd suspect an issue with the jig as an contributing factor. Is there any play in the jig's run through the miter slot? Any wiggle in the slot will result in a curved cut just from the slight change in push angle. That's one reason I have my TS sled indexed to the left table edge as well as the left slot; no room for sled/slot wiggle that way.

Last thought: Are you engaging your blade tilt lock at the set tilt? A tiny bit of play in the trunnions that the lock should eliminate may be part of the issue.

Re: I'm baffled, table saw cut problem.

#12

Some more thoughts

jeff

>This happenned with 2 different jigs.

I have a third one and will also try it.

Also, will try a simple Miter guage.

Also, this happenned with 20 cuts on cherry stock, but will also try a piece of oak and mdf for testing.

I'll try all the simple tests and adjustments first.

I need to be careful and not change more then 1 thing at a time and get myself confused or make things worse.

I'll be in the shop as soon as I get finished with the office stuff this morning.

Hopefully, I'll have it nailed in a few hours.

Jeff

Re: I'm baffled, table saw cut problem.

#13

A second question

jeff

>I use a Grizzly 1023 cabinet saw.

If the saw is out of alignment on 45 cuts and not 90 degrees as was suggested:

How in the world do you fix that problem?

Jeff

Oh God, where does it end?

Re: I'm baffled, table saw cut problem.

#14

Re: A second question

Dan Donaldson

>You shim the table. On cabinet saws, they usually bolt down on the corners. You add shims to various corners, testing at 90 and 45 until you get it right at both settings. It usually takes a few iterations to get it right.

Re: I'm baffled, table saw cut problem.

#15

Re: A second question

Glenn Madsen in the SF Bay Area

>It ends with a sharp handplane and a shooting board type of bench jig. You then trim carefully to truly the right angles. And the fit is perfect. It isn't necessarily fast, though.

Re: I'm baffled, table saw cut problem.

#16

Here's an decent answer to that *LINK*

Tim Greif - West of Chicago

>I believe Denis Chenard addressed this back in 2005 in a similar thread. He indicated:

"If the whole trunnion/rod appartus is not in the same plane as the saw table top you will get a situation where the blade is parallel to the slots when vertical, but as you angle the blade it will lose its "parallelleness" with the saw top. The solution is to put shims under one end of the assembly. It's a trial and error thing, it was covered in an AWW article in 1995 or so ("supertune your tablesaw" was the title)."

The article below is a very good discussion of this and was based on observations by Steve Strickland, a wooden puzzlebuilder who was a fanatic for alignment accuracy. It's a good read.

Good luck.


Alignment article

Re: I'm baffled, table saw cut problem.

#17

Re: I'm baffled, table saw cut problem.

Rick Christopherson

>


When I put a straight edge on the point of the 45, you can see a small gap in the center.
When you said you were measuring at the point of the cut, I misread this and thought you were describing a convex shape vertically on the bevel. This is not a common problem, and that is why i was surprised by it.

After re-reading this passage again, I see that you are experiencing the much more common problem of the cut being convex across the length of the bevel.

The miter slot adjustment I mentioned above is not a cause of this type of symptom, but the low blade height can still be a cause. More often than not, this is caused by the workpiece not being flat, or for similar reasons, lifts off the table during the cut. Another common problem is allowing the workpiece to move laterally during the cut, but this typically does not result in a convex cut, but a diagonal cut.

Re: I'm baffled, table saw cut problem.

#18

BTW, this should all be in your manual

Tim Greif - West of Chicago

>Grizzly manuals address this phenomenon in a section titled.Blade Parallelism. Check your manual somewhere around page 40. It discusses what to do when you're parallel at 90 degrees but not at 45 degrees.

Re: I'm baffled, table saw cut problem.

#19

BOY, HAVE I GOT TROUBLE!

jeff

>I should have quit while I was ahead!!!

Finally got into the shop.

First, I tried a piece of flat oak to be sure of the problem.

Still had the concave cut, also tried an old piece of flat cherry that I had, and same problem.

Second, I tried raising the blade as high as it would go. The cut was concave, but less.

Third, took my blade off, cleaned the arbor and arbor flange, and gave a light sanding to the washer to be sure there was no problem with debris.

Forth, tested the arbor flange with a dial indicator for any wobble.

Tested ok (no readable error.)

Fifth, put on a Master Plate and tested the alignment of blade to miter slot. Had 2 Thou out from one side to the other, on a 90 degree cut.

Moved to 45 degee and had 25 thou out from one side to another.

Oh No, Trouble!!

Sixth, Figuring things couldn't get worse:

I put a new Forrest Chopmaster (right from the box) on and tried a test cut.

The good news, got a beautiful glass smooth, one you couldn't improve on if you tried.

The bad news, the straight edge showed a convex cut. I mean it literally rocked, it was rounded.

So, I raised the blade as high as it would go, and retried.

Again I had a ever so slight convex cut.

Now what to do?

Jeff

Re: I'm baffled, table saw cut problem.

#20

Re: BOY, HAVE I GOT TROUBLE!

Dan Mitchell

>With regard to the discrepancy between the miter slot & the blade when the blade is at 45, it sounds to me like the top may not be level front to back. I have a PDF of a very good Fine Woodworking table saw tune up article which I can email to you if you'd like, let me know.

Dan

Re: I'm baffled, table saw cut problem.

#21

Yes, please

jeff

>

Re: I'm baffled, table saw cut problem.

#22

Hold everything and try this.

Ken Dolph

>I have been watching your post. I thought that I had the answer but everyone seemed to know better.

Try this. SLOW DOWN. I cut Corian all of the time. Corian has no grain and is not reactive but I do see this from time to time. No blade is perfect. It will cut better on one side than another. The faster you push the wood through the saw, the more the blade will pust to the better cutting side, especially if you are cutting off a thin strip which offers less resistance.

The fact that the only real change that you made was to change blades and the cut went from concave to convex, confirms this, in my mind.

I know that there appear to be problems with cutting wood slow, especially with reactive wood. Please humor me, try the same cut at 30 to 40 inches per minute. This will seem like the sun setting in the west but we cut our error rate and increased blade life 11 times by taking this advice of my saw sharpening guy.

I hope this helps

Ken

Re: I'm baffled, table saw cut problem.

#23

Re: Hold everything and try this.

Dan Donaldson

>The only thing is that his blade is quite a bit out of square at 45.

Re: I'm baffled, table saw cut problem.

#24

Done

Dan Mitchell

>Let me know if you get it & if it helps.

I had the same 45 degree anomaly with my PM2000 when I 1st got it, had to shim the front of the table. If it's a slight error, you can use pieces cut from pop cans etc., mine was off so much I ended up using fairly thick washers.

Dan

Re: I'm baffled, table saw cut problem.

#25

No Help

jeff

>My manual hasn't any info or help.