Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

question on Delta and Biesemayer fences

Posts

question on Delta and Biesemayer fences

#1

question on Delta and Biesemayer fences

pecker

>I was looking at the new Delta contractor saws at a woodworking show recently. When I released the locking handle on the fences, they went out of square and the cursor moved an 1/8" or so.

Now all my experience has been with a Ryobi saw, but with it I can easily unlock the fence, bump it 1/32"...or less if I'm careful, and get some pretty precise cuts made.

The Delta's and Biesemayer did not seem like there was any way to do this. In fact, until the handle was locked, I could hardly tell where the cursor would end up, as it moved a bit as it squared up the fence to the rail.

Were these things just set up improperly, or is that how these type fences behave?

Thanks for any experienced answers.

Re: question on Delta and Biesemayer fences

#2

Re: question on Delta and Biesemayer fences

Tony - Memphis

>My Beis does move a little when I actuate or release the locking mechanism. My method for fine adjustment is to half-engage the lever to snug the fence and then bump it with my hand. Seems to work well. But if the lock is totally released and I move it to a spot on the ruler, when I clamp, it will move a little. It has to have a little play to be able to move well.

Tony

Re: question on Delta and Biesemayer fences

#3

Re: question on Delta and Biesemayer fences

JW

>The saw must have been set up poorly.

I have the Biesemayer on my Uinisaw and I can make tiny adjustments to the fence as small as 1/64 or just a hairline without any problems. The fence should not move at all when the fence lock is released. I can also make very repetitive cuts even after moving the fence out of position, and coming back to the same place.

That saw you saw (pardon the pun) was problably not aligned properly and tension spring not set up peoperly. You'd think yhey'd set up the saw properly since that would be their showpiece!

Re: question on Delta and Biesemayer fences

#4

Re: question on Delta and Biesemayer fences

David Hay @ Denver

>It sounds to me that the saw was either not set up correctly, or had been knocked out of adjustment over the course of the show. Most of these fences have four screws (two on top of the rail, two on the side of the rail) that adjust not only the alignment of the fence, but also have the secondary effect of changing how snug the fence is against the rail.

I have no trouble unlocking my Unifence and making small adjustments.

David

Re: question on Delta and Biesemayer fences

#5

Re:Fence too tight

Robin Corell in Atascadero CA

>Sounds like your fence is set up with too much tension in the locked position. It should take very little force to lock the knob. When set up properly the fence will not move when locking. It will also seem like it couldn't possible be snug with so little force on the locking knob, remember this is a cam lever and as such the force is multiplied.

Robin Corell

Re: question on Delta and Biesemayer fences

#6

Re: question on Delta and Biesemayer fences

Rixk L

>On the Bies you just loosen the handle and it stays true and can easily be nudged then locked in place. Lifting the handle all the way up is only to remove it from the table.

Re: question on Delta and Biesemayer fences

#7

Or to keep from walking into it…DAMHIKT____

Rod Peterson -- Ormond Beach

>

Re: question on Delta and Biesemayer fences

#8

Don't Have that Problem with Mine

Robert Hutchins

>