Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

How do you cut your sheet goods?

Posts

Re: How do you cut your sheet goods?

#26

Re: Very Slippery

CARL BARTON

>I have an entire line of FESTOOLS, the TS55, the router, 12v drill, and jigsaw, along with the dust collection system. The previous tools I had were very old, 30 years, and had seen allot of use. So I went to my local woodcraft store thinking I was just going to buy a drill and came $2500 poorer, but man I tell you I love these tools. The LOML was very understanding, but after she saw how much dust they collected and how much better these tools she just handed me a list of projects to do. :)

Carl

Re: How do you cut your sheet goods?

#27

;-)

Falberg saw Co

>

Re: How do you cut your sheet goods?

#28

Re: How do you cut your sheet goods?

Jim-IL

>I made 2 cutting guides out of 1/2 inch ply with a 3/8 ply glued on top to run my worm-drive skillsaw against. One 8' long and the other 4' long. I put the plywood to be cut on sawhorses on top of some 2 x 4s and clamp my cutting guide on top of this. I get very accurate cuts this way. On the 3/8 piece I use the factory edge to run the saw against.

Re: How do you cut your sheet goods?

#29

Thanks for responding!!!!!!!!!!

Lee Beeden....A Brit in Canada

>

Re: How do you cut your sheet goods?

#30

Some people don't have siders?

Joe Dusel (Vista, CA)

>That's so sad! I just can't imagine cutting panels without a slider. Well, I guess you could just cut the panels on your CNC router.

I would say the Festool saws would be a good way if you didn't have a slider.

Joe

Re: How do you cut your sheet goods?

#31

Re: How do you cut your sheet goods?

John Smith

>I use the EZ Smart system, including the EZ Smart table. Very accurate system, and useful for more than sheet goods.

Re: How do you cut your sheet goods?

#32

Re: How do you cut your sheet goods?

Ray Lewis - Ohio

>I have a cut list from my computer. Ii then use a clamp on straight edge with a Porter-Cable trim saw and a panel blade to get the full sheets to a smaller size. I then go to my table saw.

Re: How do you cut your sheet goods?

#33

rigid foam weighs a lot less

Dave Morris

>Am I the only guy who uses a cheap piece of rigid foam as a sacrificial backer board? Bought a single 4x8 piece, cut into half for easier storage against the wall. I cut with a skill saw, good blade, shop-made 1/4" thick plywood saw guides for cross- and full-length cuts, and can get glue-line cuts. Beats manhandling full sheets on the TS.

Only real problem is finding enough open floor space in the shop if the weather isn't cooperating for driveway use. I'm about due for another piece of foam though, cuz the old one is looking kinda tattered.

Dave--- who has to take the low-buck route until the kids graduate from college

Re: How do you cut your sheet goods?

#34

Re: How do you cut your sheet goods?

John Stegall

>Festool circular saw with guide system. On rare occasions I will finish up on the Unisaw, but very rare indeed.

john

Re: How do you cut your sheet goods?

#35

Re: How do you cut your sheet goods?

john lucas

>30 year old Craftsman circular saw with a thin kerf carbide blade and an aluminum straight edge with clamps. Then to the table saw.

Occasionally if I really need to scrimp on the plywood I'll use a jig saw and cut close to the line. then I'll take these pieces to the table saw.

Re: How do you cut your sheet goods?

#36

Re: How do you cut your sheet goods?

Larry in NW Ohio

>Ray I have the P-C Trim saw also, to cut thin matterial. I really like it. Larry in Ohio

Re: How do you cut your sheet goods?

#37

Re: How do you cut your sheet goods?

NickB

>I actually have a (Rojek) slider, and I still cut down to rough size before I get onto the table saw, as I have little affection for handling full sheets of plywood on the table saw. I use a PC 345 combined with a power tool guide from Lee Valley. I bought one of the sliders (or whatever they call it) that rides on the tool guide, and hooked it to the saw via a zero clearance sole plate (1/4" plywood). I have to be careful where/when I put the saw down (the zero clearance plate means the blade guard can't work), but it does really, really well for rip cuts, so-so for cross cuts (but that's what the slider excels at). Before I got my Rojek, I used a framing saw and took two passes for cross cuts-the first very, very shallow (approximating the scoring blade on my Rojek) and the second the cut all the way through.

Hope this helps,

Nick