Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

band saw blade jumps off the lower tire

Posts

band saw blade jumps off the lower tire

#1

band saw blade jumps off the lower tire

Philip Duffy

Need some advise before spending unnecessary cash. Changed the blade 2 days ago and did not do any sawing after the change. But today, a few simple cuts resulted in the blade backing off the bottom wheel (Jet 14in with riser block). Several attempts to adjust the blade track and tension resulted in the same loss of the blade. Bottom wheel seems to be tight on the shaft. Is it the tires?? They are about 4 yrs old. All advise appreciated. Philip

Re: band saw blade jumps off the lower tire

#2

Re: band saw blade jumps off the lower tire

Bruce Pratt

Sounds like a bad blade. Do you have an old blade you can put back on to see if it is the blade or the tires?

Re: band saw blade jumps off the lower tire

#3

Re: band saw blade jumps off the lower tire

Philip Duffy

yes, I will try that. Tks. P.

Re: band saw blade jumps off the lower tire

#4

Re: band saw blade jumps off the lower tire

Brian Roberts

If the previous blade tracked fine....then it's a process of comparison and elimination.

Same type, size, thickness, etc. new blade?

Tires on the wheels were not disturbed, moved, etc.?

Joint/weld on new blade is correct....blade ends were cut at a correct 90 degrees at the weld?

Put the old blade back on....does it track?

Re: band saw blade jumps off the lower tire

#5

Re: band saw blade jumps off the lower tire

Jim Horsley

I suspect a defective new blade however if the bottom wheel appears tight on the shaft you may have a bad bearing. That happened to me on an older saw.

Re: band saw blade jumps off the lower tire

#6

Re: band saw blade jumps off the lower tire

Dick Coers

I've had tires last 30+ years, so age has nothing to do with it. If the tires are clean and snug on the wheel, they are okay. Do you see an oscillation of the blade near the thrust bearing? If you don't see that, doubt if it's the blade. Did you readjust the upper and lower thrust bearing with the new blade? Is the new blade the same width as the old?

Re: band saw blade jumps off the lower tire

#7

Keith Tompkins

Re: band saw blade jumps off the lower tire

Keith Tompkins

Hi Philip, I would make sure the two wheels align with a straight edge; you can see the wheels are out of alignment if the blade tracks close to the front edge on one wheel, and near the back edge on the other. If the tire came loose, it may be re-cemented, (in an emergency) but preferably replaced. The tires should never come off. Hope this helps

Re: band saw blade jumps off the lower tire

#8

Re: band saw blade jumps off the lower tire

Philip Duffy

First, let me thank all of you who gave so freely of very good observations and advise.

Now, for the lessons learned, passed because I feel a need to keep others from making the same mistakes.

1. The tires are slightly worn so I glued them back on the wheel with contact cement and then smooth it out with a stick on the wheel while running. Yes, not very safe but I was extremely careful.

2. Just by checking around I found the big bolt that holds the Riser Block in place was slightly loose but perhaps enough to cause or contribute to the loss of the upper wheel bearing.

3. The nut holding the upper wheel in place was actually loose. Not a lot but enough that the wrench turned 1/8 rev.

All this points out the need for scheduled maintenace on the usually reliable bandsaw. At the moment my upper wheel sits at a shop which will pull both upper wheel bearings and by tomorrow I should be ready to put a blade on the wheel with new bearings and watch it humm.

Check your machinery Quarterly, ladies and gents or suffer the outages like I just did. Philip