Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Stuck insert on SuperNova chuck

Posts

Stuck insert on SuperNova chuck

#1

George Taylor

Stuck insert on SuperNova chuck

George Taylor

I am trying to disassemble several chucks for long overdue cleaning. I got the set screws out but the inserts won't budge. I am headed to the hardware store because all I have is a set of channel locks. Tried to lubricate with some oil and still no dice. What tool(s) do I need (I am a tool junkie) and how should I approach?

Thanks in advance.

Re: Stuck insert on SuperNova chuck

#2

Re: Stuck insert on SuperNova chuck

John Jordan

It has threaded holes to jack it out if I'm not mistaken.

John

Re: Stuck insert on SuperNova chuck

#3

Re: Stuck insert on SuperNova chuck

Clifton C

A friend of mine brought his over with a stuck insert. We clamped a 3/4 inch board in a vice with about an inch or so above the jaws, then gripped that with the jaws of the nova, a breaker bar and an inch and a half six point socket and a nudge and we were done…

no muss no fuss. There is a set screw that has to be backed out, but I think what helped

the most was that the chuck was chucked to a piece of wood chucked in the vise, so no

wiggle. Plus you have two hands free to wrestle the insert. Just another angle.

cc

Re: Stuck insert on SuperNova chuck

#4

Re: Stuck insert on SuperNova chuck

Ivan Clark

What Clifton said, plus pick up some PB Blaster and let some soak into the insert threads overnight before you follow his method.

Re: Stuck insert on SuperNova chuck

#5

Re: Stuck insert on SuperNova chuck

Geoff Whaling

George,

These may help -

http://www.teknatool.com/products/chucks/supernova2/downloads/maintance%20of%20supernova2%20chuck_oct04.pdf

http://www.teknatool.com/products/chucks/supernova2/downloads/supernova2%20maunal%20full%20version.pdf

Some manufacturers suggest soaking the chuck in kerosene, mineral/white spirits before you attempt to disassemble them.

Just make sure you have removed the M6 grub screw before applying brute force.

Re: Stuck insert on SuperNova chuck

#6

Re: Stuck insert on SuperNova chuck

Steve Kniffen

George,

Had the same problem a couple of weeks ago. I read the manual as suggested above. I put a pipe wrench on the insert, held the chuck tightly with one hand and lightly tapped on the end of the wrench handle with a rubber mallet. About the 3rd tap, it came loose.

Steve

Re: Stuck insert on SuperNova chuck

#7

why take the insert out

Darryl

Are you certain you have to take the insert out to disassemble to chuck? Can't you just remove th "C" clip and remove the back. they are all bigger than the 8insert ridge.

Re: Stuck insert on SuperNova chuck

#8

Re: why take the insert out *LINK*

walta

What you need to remove the insert is an impact.

The way I do it is clamp a piece of plywood on the jaws of the chuck and put the ply wood in a vise with the insert facing up put a 24 inch Crescent wrench on the insert and tap the wrench with a hammer.

I do own the nova wrench It is handy is it will fit between the chuck and head stock.

http://www.teknatool.com/products/chuck_accessories/spanner.htm

Most any service station should have an impact wrench and socket that would free the insert in seconds.

I think a pile wrench is a poor tool for this job as it will tend to crush the thin aluminum insert. Even if the insert survives the hardened steel jaws will damage the soft aluminum.

I hope you are lucky and have a genuine Tekatool insert and not the cheap knock off sold by Woodcraft as it features rounded corners. The insert is a nut and I call a nut with round corners stripped!

Walta


horrible freight

Re: Stuck insert on SuperNova chuck

#9

Impact - did some one say impact?

Geoff Whaling

I would not recommend applying brute force to the jaws / jaw slides / scroll of a chuck. Far better to hold the chuck body in an engineers vice to remove the insert.

Damaged scrolls in chucks are bloody dangerous. I've pulled down and serviced many chucks with broken or damaged scrolls, particularly the leading edge of the scroll.

I have seen chucks which were stiff in operation in one part of their range for no apparent reason - until you open them up. How does a scroll get a small ding in the scroll itself??? My thoughts are it can only happen from "chuck abuse."

Any technique that utilizes impacting the jaws is risky and prone to cause damage that is not easily seen until you strip a chuck.

Re: Stuck insert on SuperNova chuck

#10

Bill Blasic

Re: why take the insert out

Bill Blasic

OK Walta what is a "pile wrench"? And what aluminum insert are you talking about? I'm confused as all he inserts I have for my Novas are steel. Sign me confused.

Re: Stuck insert on SuperNova chuck

#11

George Taylor

Cheap insert going in the trash

George Taylor

Finally got an appropriate wrench and was able to unscrew it from the chuck body. Used the wrench to lock the insert against the lathe and then unscrewed the body. Threads were damaged on the insert; probably Woodcraft if the telltale sign is the rounded corners as someone suggested. Thanks all, now onto cleaning.